L | P, 8 C B X- -L-x- (а) B L-x C 2 d A (b)

Q: Tsup 3 m 7m Tamb KA Ke

A: GIVEN DATA-

Q: v (m/s) 10 t(s) 15 60 90

A:

Q: For 602.28 kPa Evaporator (8) temperature and degree superheat leaving the compressor (h) mass of va...

A: Given data Standard refrigerating cycle withEvaporator pressure = 602.28 kPa ≈ 6 barCondensing Press...

Q: A square tube section has side dimension of20 in. and thickness of 0.5 in. If the section is used fo...

A: Given Thickness = 0.5 in Length = 10 ft = 120 in Torque = 1250 kip in= 1250000 lb in G = 11600 ksi =...

Q: Describe the environmental impacts of wind power systems and explain how the negative impacts of win...

A:     Solar energy comes in the form of wind. The method of generating electricity with wind energy (o...

Q: If a material had a modulus of elasticity of 2.1 × 106 kgf/cm² and a modulus of rigidity of 0.8 x 10...

A: From the data given in question, Modulus of elasticity = E = 2.1 x 106 kgf/cm2 Modulus of rigidity =...

Q: b) Determine the energy transport rate for the system shown in Figure below. Fuel flow Epe15,000 Btu...

A:

Q: A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which ...

A:

Q: (c) work on compressor in kW (d) work on compressor per ton of refrigeration (e) coefficient of perf...

A: Given that: The refrigerant is R22. Refrigeration capacity = 82 kW. Compressor suction pressure = 35...

Q: Air enters an air - standard Otto cycle with a pressure and temperature of 1 bar and 15" respectivel...

A:

Q: Determine the speed of block A after 1 second, if the rope drawn towards M at a speed of VM = (5t3/2...

A:

Q: If the stream function is y = 2xy, then the velocity at a point (1, 2) is equal to:

A:

Q: Two random particles X and Y were being studied by a bored individual. Upon observing, he defined th...

A:

Q: A rigid vessel as shown in figure below contain three different gases separated by diaphragms. If di...

A: Given that, CO2:m=24 kg,T=77 °C,P=1.5 bar,N2:m=6 kg,T=52 °C,P=0.5 bar,O2:m=12 kg,T=27 °C,P=2.0 bar,

Q: ME. BOARD FEBRUARY, 1951 In a certain diesel- alactric power plant, dieset generator set has the fol...

A: Given Datadiesel fuel consumption =109495kgP=518000kWT=596hrsηg=90% ***As per our company policy we ...

Q: Reqd: Determine e of A relative to D Gs = 12 x 10° psi MN Ib ft 1000 Ib ft 900 Ib ft 2-in. diame SN ...

A: The simplified diagram of the shaft is as shown below,

Q: A mechanical part is made up by the union of two triangles, as illustrated in Figure 3. Both triangl...

A:

Q: Find Tension T and the components Rx and Ry of the force R exerted by the pivot.

A:

Q: A vessel contains at 1 bar and 20°C a mixture of 1 mole of CO2 and 4 moles of air. Calculate for the...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: Shown in the figure is a gear-driven squeeze roll that mates with an idler roll, below. The roll i d...

A:

Q: A car is traveling around a circular track of 780-ft radius. If the magnitude of its total accelerat...

A:

Q: Given a system as shown in the following figure. Calculate the water level difference between two ta...

A:

Q: ) A large pipe with a cross-sectional area of 1 m' descends 5 m and narrows to 0.5 m2, where it term...

A: To solve this problem, we have used bernoulli's equation and equation of continuity, speed of the wa...

Q: The diagram below shows a composite wall 1 m deep. The first layer of thickness LA is made of specia...

A: GIVEN DATA- A COMPOSITE WALL GIVEN WE HAVE TO FIND THE THICKNESS OF WALL A

Q: Q1/ Find the resultant (R) and the direction (N) of the two forces show in Figure below ? The angle ...

A: It is required to determine resultant force and it's direction

Q: 3. Identify the process in Fig. 2 and write down the conservation equations. m What process? w, w, T...

A:

Q: (a) mass flow rate of refrigerant in kg/s (b) mass flow rate of refrigerant per ton of refrigeration...

A:

Q: An arm ABC lying in a horizontal plane and supported at A (Figure 4) is made of two identical solid ...

A: Given that, Length of bar, LAB=LBC=0.5 m,Principal stress in bar, σ=6.40 MPa, Let 'G' be the centroi...

Q: F2-3. Determine the magnitude of the resultant force and its direction measured counterclockwise fro...

A: Answer: (a) The magnitude of the resultant force is 721.110255 N. (b) It's direction measured counte...

Q: Q9. A 24-kg box was thrown onto a 35-kg cart with a speed of 7 m/s in the as shown. The cart was ini...

A:

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the...

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m 

Q: 9. A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of ...

A: Given Data P=50 kN D=20 mm L=600 mm ∆=1.4 mm D'=19.9837 mm

Q: The velocity of the particle that travels along a straight line is v = (12 - 3t2) m/s, where t is in...

A: Given Data

Q: Q4/ Using three different ways, compute the the moment of the force 400 N about O? 400 N 100 mm 60 1...

A:

Q: A reducing bend has a linear velocity at section 1. See Figure 4. The flow is uniform at sections 2 ...

A:

Q: How does resonance occurs in a dynamic system? What must I take into account from preventing this fr...

A:

Q: 2- Assume that the outside air temperature is 32°C with a relative humidity p = 60%. Use the psychro...

A:

Q: An ideal gas at 27 oC is heated at constant pressure till the volume becomes three times. The temper...

A: From the given data, Initial temperature = T1 = 27 oC = 300 K   Let us take, Initial volume = V1 Fin...

Q: 3. Determine the normal force, shear force, and moment at a section through point C. Take P = 8 kN B...

A:

Q: if a weldment is heated to correct distort from welding, the maximum localized he

A: if a weldment is heated to correct distortion from welding, the maximum localized heat shall not exc...

Q: QI Compute the angle (Theta) for the member (A), the resultant force of FA and FB is directed horizo...

A:

Q: Q1/ Find the resultant (R) and the direction (N) of the two forces shown in Figure below ? The angle...

A: It is required to determine resultant force and it's direction

Q: A simply supported beam ABC is loaded at theend of a bracket BDE (see figure). Draw axial-force,shea...

A: Draw the free-body diagram of beam ABC.

Q: For the joint shown in the figure, if F = 28 kN and dp = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm ...

A: Answer: (a) The largest bearing stress is 182.29 MPa (Option b). (b) The average shear stress is 108...

Q: Q4/ Using three different ways, compute the the moment of the force 400 N about O ?

A:  According to the details provided in the question, we need to calculate moment about 0 due to force...

Q: Determine the pumping power (in kW) required, if water at 30°C is flowing through a pipe length of 1...

A:

Q: Problem 6 A projectile is fired from ground level with an initial speed of 100 m/sec and an angle of...

A: Problem 6

Q: Buoyancy 1. An iceberg having specific gravity of 0.92 is floating on saltwater of SG 1.03. If the v...

A: Answer: The total volume of the ice is 9364 m3.  

Q: the velocity (C,) of steam (in m/s) at the nozzle exit

A: Given: Steam flows through a nozzle at  mass flow rate: m=0.1 kg/sHeat loss of: Q=5 kWThe enthalpies...

Q: Calculate the maximum def lection δmaxof a uniformly loaded simple beam if the spanlength L = 2.0 m,...

A: Given   Load, q = 2 kN/m Length, L = 2 m              E = 70 GPa Find  Maximum deflection

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.