Exp. No. 11: SHIFT REGISTERS Logic Laboratory Discussion: 1. Generally, what is the difference between a counter and a shift register? 2. What two principle functions are performed by a shift register? 3. How many clock pulses are required to enter a byte of data serially into an 8-bit shift register? 4. What are the differences between SISO and PIPO shift registers.

Exp. No. 11: SHIFT REGISTERS Logic Laboratory Discussion: 1. Generally, what is the difference between a counter and a shift register? 2. What two principle functions are performed by a shift register? 3. How many clock pulses are required to enter a byte of data serially into an 8-bit shift register? 4. What are the differences between SISO and PIPO shift registers.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Assume r1 = 2, r2 = 3, r3=8. Write an ARM assembly code to calculate 2 * r1 + 5*r2 - r3/2using logical shi le/logical shi right/arithmetic shi right. Store this result in register r6.
Q#02) Explain Direct Memory Access (DMA), and Input/output timing diagram with clock synchronization.
a) In a 32-bit register array, what would be the selection bits to read a data from $17? b) What kind of problem can variable sized instructions can create? In which type ofarchitecture, it is used? Give 2 examples of that architecture.c) Why do you think adding more transistors in a single chip is not possible?
Please use Logism and please show your work Design a 4-bit ALU that performs Arithmetic (add, subtraction), and Logic operations (AND, OR). • R/W: read/write signal (0:read, 1:write) .Simulate your design. The details of each control signal (Unit) are as follows Design three 4-bit parallel registers to hold A, B, and C where C keepsthe output of the ALU. The registers have a R/W control signal that indicates that theyare being written to or read from.
Show an image of the completed 8 BIT ALU The most important and possible most difficult component to implement is the arithmetic logic unit. Thefunctions of the ALU are shown in Table 1. The ALU should have 5 inputs (A-input, B-input, F0-input, F1-input, Finput) and 1 output (C-output). You will need to determine how many bits each input and output should have.Remember, you are designing an 8-bit microprocessor! To achieve the specified ALU functions, think aboutwhich digital logic component(s) you can use to accomplish the task. For example, to add the value on the A-bus8-bit ALUto the value on the B-bus, you can simply use an 8-bit adder. Explore the components in Logisim! Additionally,you can think about using a multiplexer to determine which ALU function will be performed
Look at the figure, can you explain to me from the figure the following special registers in the CPU: IR, Imm, A, B, C, NPC, LMD? Tell what they're doing.
What are the bits of register DI that have been set in the instruction, OR DI, 1234H?MULTIPLE CHOICESA. all 16 bitsB. bit 2, 3 ,4, 9,12C. bit 2, 4, 5, 9, 12D. bit 1, 2, 4, 5, 12
A1 a)Explain how 8051 interrupts operate in a microcontroller. b)To prove the statement, use a diagram or analogies to aid your description.
a) Write a program in 8051 to copy the contents of registers R0 to R7 into internal RAM addresses40H to 47H respectively using PUSH instructions. Assume Register Bank 0 is selected. b)Observe the timing diagrams given in Fig. A and Fig. B below and identify the mode of operationwhen these kind of waveforms are produced on the OUT pin of the IC. Also, name the IC and explainthe mode during which the following output waveforms were produced.
Differentiate between the function of the following 8086 IC pins: HOLD and HLDA INTR and INTA (active low) A0-A15 and AD0-AD15 Mx/Mn RQ/GT0 and RQ/GT1 (active low) B) How the clock generator chip (8284A) is used to provide the clock for the microprocessor?
What memory address range is NOT represented by chip 1 and chip 2 in figure? A0 to A15 in this figure are the address lines and CS means Chip Select. (Gate 2005) Explain the program memory structure of 8051 microcontroller. Write an ALP using 8085 online simulator tool to perform logical XOR operation for two 8 bit data. Load the accumulator with 34 H and load the B register with 1AH.
1.How many shift pulses are required to serially load a 16 bit word into a 16 flip-flop shift register? 2. How could you reset an 8-bit serial in-serial out shift register? 3. A binary number is shifted 4 positions to the left. What is the number?