Please draw a ladder diagram (plc) for this question Experimental Procedure:You are requested to use SIMATIC S7-300 PLC to control a production line (minimechatronics trainer) with a traffic light signal.Write a Step 7 program to control the following operations:(1) Use a push button to initiate the system and turn the conveyor on and another push button toturn the system/conveyor off, then using 3 LEDs to simulate a traffic light operation as follows:a- Turn on the green light for 5 s; while all the other lights are off.b- Turn on the yellow light for 5 s; while all the other lights are off.c- Turn on the red light for 40 s; while all the other lights are off.d- Repeat the sequence for infinite time as long as the system is ON.(2) When green turns on, eject a workpiece from the feeder magazine; the conveyor transfers it tothe stopper, which opens the way to the container, then closes again. Eject a piece each timegreen turns on.(3) Use the inductive sensor to count the number of metal workpieces in the container.(4) Use the capacitive sensor to count all workpieces in the container.

Answered: Image /qna-images/answer/3940c2ac-9868-4074-b308-a263586b3029.jpg

Answered: Experimental Procedure: You are…

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter53: The 555 Timer

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

How many DOF do the following have in their normal environment ? a. submerged submarineb. An earth-orbiting satellitec. A surface shipd. A motorcyclee. The print head in a 9-pin dot matrix computer printerf. The pen in an XY plotter
For a 1-degree-of-freedom robot arm, it is needed to use a DC motor. Draw a blockdiagram for a mechatronic system that controls the position of this robotic arm forgripping objects. Suggest a sensor system and clarify the flow and nature of signals inyour block diagram.
Where the aim of this machine is to receive two liquids, A and B, where when liquid A reaches sensor 2, it should stop flowing and then activate valve X1 to flow liquid B until the whole liquid in the tank reaches sensor 1, then it should stop the flow and turn on the steering motor and open the output valve Y0. Design a PLC Ladder Diagram + Visualization to solve the following problem. Explain how the diagram works and explaining the logic behind it step by step.
The automatic washing machine system is an example of ........... loop system.
I want you to draw a ladder logic diagram of a garage door to control it by PLC. In my case we have different inputs and outputs and all of them gotta be used in the diagram. I can perfectly interpret the diagram so no need to explain it, I will just require you to draw it. INPUTS : open push button ( OPB ) - close push button ( CPB ) - open limit switch ( OLS ) - close limit switch ( CLS ) - obstacle detection sensor ( ODS ) - safety sensor ( SS ) - emergency stop push button ( ESPB ) - reset button ( RB ) OUTPUTS : motor starts ( MS ) - motor stops ( MSTP ) - motor forward ( MF ) - motor reverse ( MR ) - Error display ( ER ) OPERATİNG MODES : automatic mode ( AM ) - manual mode ( MM ) NECESSARY TIMERS : T1 ( delay door movement after obstacle detection ) - T2 ( delay door movement after reversing ) Here is my excercise for today. Please I am requiring a good logic diagram taking into consideration all what was mentioned before. so to sum up, I want you to write a logic ladder diagram…
Write an AVR program using the timer to generate a square wave at a frequency of 50KHz knowing that the main frequency of the microcontroller XTAL is 5MHz
An industrial robot performs a machine loading and unloading operation. A PLC is used as the cell controller. The cell operates as follows: (1) a human worker places a part into a nest, (2) the robot reaches over and picks up the part and places it into an induction heating coil, (3) a time of 10 sec is allowed for the heating operation, and (4) the robot reaches into the coil, retrieves the part, and places it on an outgoing conveyor. A limit switch X1 (normally open) is used to indicate that the part is in the nest in step (1). This energizes output contact Y1 to signal the robot to execute step (2) of the work cycle (this is an output contact for the PLC, but an input interlock signal for the robot controller). A photocell X2 is used to indicate that the part has been placed into the induction heating coil C1. Timer T1 is used to provide the 10-sec heating cycle in step (3), at the end of which, output contact Y2 is used to signal the robot to execute step (4). Construct the ladder…
Using "Subjective Digital Design", please develop the Boolean equation for the problem statement given: This CNC machine controller allow operation (represented by O) of the machine if there is a part in the vice (determined by a sensor P) and the spindle is fully retracted (determined by another sensor R) or a manual override (M) button is pressed by the operator.
Design a digital lag compensator for the position control system below to meet thefollowing specifications:ess = 0.0062 in response to a unit ramp reference input, andMp ≤ 0.095 for a unit step reference input.
A proportional controller is used to control the height of water in a tank where the water level can vary from 0 to 4.0 m. The required height of water is and the controller is to close a valve fully when the water rises to 3.9 and open it fully when the water falls to 3.1 m. What transfer function will be required? source : Mechatronics: Electronic Control Systems in Mechanical and Electrical Engineering 6th Edition by W. Bolton question 22.4
Design a PID controller for this system.
18- A)Define the following(i) Sensitivity (ii) Transfer function of closed loop control system

SEE MORE QUESTIONS

Recommended textbooks for you

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

SEE MORE TEXTBOOKS