Explain about PI Control of the Integrating Pumped Tank Process
Q: A 50 MVA, 11 kV synchronous generator has internal reactance of 0.8 Q. The generator is connected to…
A: In this question we have to find out per unit impedance of generator when connected to new power…
Q: What are the poles according to their duties?
A: The function of poles is to support the conductors. poles should be capable to carry the load due to…
Q: The sum of the armature reactance and.............reactance is the reactance of the synchronous…
A: ARMATURE REACTANCE AND LEAKAGE REACTANCE The armature reaction reactance and the leakage reactance…
Q: ix. What is the purpose of surge tank in hydro electric plant?
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: 1. List out how does a priority method varies from dynamic programming method in Unit commitment…
A: NOTE: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…
Q: What is the Continuity Test?
A: A continuity test is one of the fundamental tests to check whether the circuit is complete or…
Q: 2. When a large shunt capacitor is suddenly connected in parallel with the load bus in the…
A:
Q: Ex. 318. Determine the closed-loop steady-state error given a R(s) ----->0-----> G(s) + E(s) C(s)…
A: The solution is given below
Q: Draw the circuit diagram of single phase cycloconverter. Consider the output voltage frequency fo =…
A:
Q: Explain about PI Control of the Integrating Pumped Tank Process
A: The main objective for PI control of integrating pumped tank process is to maintain liquid level at…
Q: The value of symmetrical short circuit current is ___________________ at time t=0. Zero Minimum…
A: In this answer let us discuss the concept of short circuit current and try to find its value at t=0.
Q: What is the edge of using Phase Locked Loop Demodulator rather than other FSK demodulator circuits?
A: Lock section lock, PLL is a very useful RF building block. PLL uses the concept of minimizing the…
Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system
A: RTD (Resistance Temperature Detector) is an electronic device used to detect the temperature by…
Q: The X/R circuit ratio of an automatic reclosure is inversely proportional to the asymmetrical factor…
A: Automatic recloser: It a type of switchgear that is used in overhead electrical distribution system.…
Q: in a tie-bus arrangement as shown in figure. the reactances of the generators and reactors are 0.2…
A: We redraw the circuit on per phase per unit basis: In the circuit the fault point is connected to…
Q: The unit step response of a second-order open-loop LTI system is shown below Calculate approximate…
A: The 2nd order function is defined by the equation Transfer Function=ωn2s2+2ζωns+ωn2where ωn is…
Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system).
A: Thermistor is a special type of Resistor whose resistance changes with the change in temperature.…
Q: Explain the computational procedure of load flow by "fast decoupled load flow" method
A: Fast decoupled load flow method - ALGORITHM- Step 1: Assume a suitable solution for all buses…
Q: estigate the stability of the system using Routh Criterion method.
A:
Q: Q3. In a % differential scheme, figure shown below, the two CTs have nominal ration of 100:1. The CT…
A: Given relay diagram is - Given values are -' Given ratio error of both CTs are same and that is…
Q: a) Explain the principle operation of synchronous generator.
A:
Q: Duestion of Write down the construction alternatOx with the an of diagram of operation. and write…
A: The alternator is also called the synchronous generator is an electrical machine that is used to…
Q: Find the effect of ‘clearing time’ on transient stability. Using the equal area criterion method…
A:
Q: Explain FIVE (5) iterative conditions of stopping criteria, that are considered in load flow…
A: In load flow analysis, the repetitive process of converging on the solution is referred as iterative…
Q: A system contains three non-identical 30 MW generating units each with a 5% FOR and one 50 MW unit…
A:
Q: synchronous generator operating under steady conditions supplying a load current I0 to the bus at a…
A: Although equivalent circuit of synchronous generator under steady state condition is given by Where…
Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring System)
A:
Q: Research on "Power Outage Detection and Locating Methods", roguirod nribo ito
A: Power outage is also called as the cutting of power or the power out,the blackout of power, the…
Q: Give information about this Transient stability of multi machine power system using UPFC
A:
Q: Draw and explain working of pumped storage power plant. What is flow duration curve? What are the…
A: A labeled diagram of the pumped-storage power plant is shown below: A pump-storage plant is a…
Q: Comment on the possible industrial application of cumulative compound generator types, series,…
A:
Q: Q5 (a) State assumptions to represent the multimachine equations with a single machine infinite bus…
A: The solution is given below
Q: block reduction method,
A: for block reduction, here 3 block rules r used:
Q: How do shunt capacitor banks are protected against following abnormal conditions. i. Over-current…
A: Shunt capacitor banks are commonly used to improve the power factor of a network. They also aid in…
Q: Another name of driving-point admittance is O Self admittance O Mutual admittance O Leakage…
A: In this question we will write another name of driving point admittance and slack bus...
Q: ineed conclusion for this topic( improvement of transient stability by using turbine fast valving…
A: Turbine fast valving method : Fast valving is a means of reducing turbine mechanical input power…
Q: 6.1. A power system network is shown in Figure 47. The generators at buses 1 and 2 are represented…
A: The power system network is shown below,
Q: Which compressor type uses tapered, machined gear components to trap the gas for compression
A: The screw compressor are the replacement of the piston compressor where the large volume air at high…
Q: Q5 (b) A synchronous generator and a motor are both rated at 30MVA, 2kV and both have transient…
A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…
Q: Two generating units rated for 500 MW and 400 MW have governor speed regulation of 6.0 and 6.4…
A: Here speed governor is given and we need to find new speed governor at 1000MW base
Q: why is there a phase shift in rc cct?how do we make it exactily 90 degree?
A:
Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system).
A: RTD's working principle is that the electric resistance of a metal changes due to change in…
Q: Problem 4: Consider an interconnected 50-Hz power system that contains four turbine-generator units…
A: The solution can be achieved as follows.
Q: 6- Why it is possible to short circuit the differ tia generator and not the cumulative compound…
A: Compound generator consists of both series and shunt filed windings. If the flux produced by both…
Q: I. Stability: Tell if the system is stable, marginally stable or unstable using Routh Hurwitz…
A:
Q: 1.Static synchronous compensator (STATCOM) for power factor improvement. 2. What are the…
A: 1.Static synchronous compensator (STATCOM) for power factor improvement. 2. What are the constraints…
Q: A 100-MVA, 20-kV synchronous generator is connected through a transmission line to a 100- MVA, 20-kV…
A:
![Explain about PI Control of the Integrating
Pumped Tank Process
( type by keyboard
3 pages )](/v2/_next/image?url=https%3A%2F%2Fcontent.bartleby.com%2Fqna-images%2Fquestion%2F7899cd0b-cabf-4b7f-b24b-4976a45aeff2%2F90c7298e-65d8-42ae-b2bc-3ea34c6be9a6%2Fgtd9ciw_processed.jpeg&w=3840&q=75)
![](/static/compass_v2/shared-icons/check-mark.png)
Step by step
Solved in 3 steps with 2 images
![Blurred answer](/static/compass_v2/solution-images/blurred-answer.jpg)
- ASAP How reverse bias operates in: a. Depletion region B. Majority carrier C. Minority carrierExplain the application of Diac, Triac, SCR and IGBT in industrial and power electronics based on its operating principleWhat are ASICs (Application-Specific Integrated Circuits), and in what scenarios are they preferred over general-purpose microchips?
- A common objective when manufacturing printed circuit boards (PCBs) is O a. maximizing the number of drill bit changes. O b. maximizing the number of holes drilled. c. minimizing the total distance the drill bit must be moved. O d. minimizing the number of holes drilled.Define FACTS and write it’s necessity and Benefits. With neat diagrams briefly describe different types of FACTS controllers. Describe SVC and STATCOM and compare their performanceA diode is an example of ___ switch. A. SPDT B. passive C. active D. DPDT
- By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choiceii. Describe the role of the process reaction curve ( Figure 3 )and the Ziegler-Nichols PID tuning rules (Table 1) in control system design. Tangent line at inflection point Figure 3 Table: 1 Zeigler-Nichols PID controller Tuning rules Type of Controller K, T T P. 00 0.95 125 PI 0.3 PID 2L 0.5L Imnortant Note:a) Buses are the conductive channels found in the circuitry of a microprocessor. This means that there is potential for current to flow among the various parts. Expertly classify these buses according to their function and describe how they interact with microprocessors.b) In a microprocessor, what is the distinction between data and instructions?
- Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripplesDiscuss the importance of "manufacturing processes" in achieving higher densities and better performance in microchips.TTR 300 , what are the features (specifications) of the device ?
![Electricity for Refrigeration, Heating, and Air C…](https://www.bartleby.com/isbn_cover_images/9781337399128/9781337399128_smallCoverImage.gif)
![Electricity for Refrigeration, Heating, and Air C…](https://www.bartleby.com/isbn_cover_images/9781337399128/9781337399128_smallCoverImage.gif)