Explain three reasons why MOSFETs are typically used in computers instead of BJTs.

Q: Explain why it is important to minimise VCM - Vg, even if the instrumentation amplifier has…

A: Op amps, in-amps, and difference amps provide common-mode rejection. However, in-amps and diff amps…

Q: Explain how the ac gain of a transistor can be controlled by a dc AGC level.

A: AGC (Automatic gain controller): Automatic gain controller is a mechanism where the overall gain of…

Q: Type your question here Derive the relation between output signal to noise ratio and input signal to…

A: to derive the relation between output signal to noise ratio and input signal to noise ratio for…

Q: a) Draw the AC equivalent circuit for the common emitter amplifier shown in Figure 1. b) Draw the…

A:

Q: Draw block diagram /circuit diagram of the ff. FM circuits and discuss the operation.   c.…

A:

Q: 3) Draw the Input and output Characteristics of BJT for CE configuration

A: The above question is related to the topic of Electronics Devices And Circuits Input output…

Q: Compare a BJT with a MOSFET regarding their transconductances and current efficiencies.

A:

Q: State why CE configuration is the most widely used connection for large signal BJT class A…

A: CE is most generally utilized on the grounds that it gives the voltage gain needed to a large…

Q: What are the advantages of FET devices over BJT?

A: Question 1 : What are the advantages of FET devices over BJT?

Q: List three conditions need to be considered to choose a MOSFET for switching applications.

A: Following are the most important conditions to be considered when choosing a MOSFET for switching…

Q: 2. Draw the equivalent circuit model and switching characteristics of the device which is used for…

A: The device which is used for low on state loss and high switching frequency operation id MOSFET. The…

Q: A) What does VCO stand four? Show by drawing the relationship between its input and output signals.…

A: VCO stands for Voltage-Controlled Oscillator This is an oscillator whose output frequency is…

Q: Analyze a basic JFET transistor circuit ?

A: Fig 1 Fig 2

Q: Power MOSFET Operating modes

A: MOSFET is a semiconductor device used for the purpose of switching and amplifying electronic…

Q: 1. Differentiate E- MOSFET and DE- MOSFET.

A: A D- MOSFET is called depletion type mosfet and a channel is present in this type of mosfet whereas…

Q: The parameter which acts as a control for switching a MOSFET is

A: The MOSFET (Metal Oxide Semiconductor Field Effect Transistor) transistor is a semiconductor device…

Q: narrow band FM

A: we known the frequency of FM wave equation fi=fc+kfx(t) x(t) is modulating signal here kf shows the…

Q: Discuss and analyze the biasing methods of E-MOSFET and D-MOSFET.

A:

Q: circuit diagram with a load ,for the Power MOSFET

A: Mosfet is a voltage controlled Device on which pulse switching frequency and their magnitude decide…

Q: use bjt to control mosfet as a switch?

A: Bipolar junction transistor (BJT) is a current controlled device. It will be used as a switch to…

Q: Draw block diagram /circuit diagram of the ff. FM circuits and discuss the operation.   c. RATIO…

A: According to the question, we need to Ratio detector

Q: The dc voltages at the bases and emitters of the tr

A:

Q: In your own words, briefly describe the difference between the basic operation of a pchannel…

A: P-Channel Enhancement MOSFET: It is also known as PMOS, where the very low doped semiconductor of…

Q: Draw the symbol of enhancement and depletion N channel MOSFET.

A:

Q: The parameters of MOSFET circuit

A:

Q: Compare FET amplifiers over BJT amplifiers?

A: Consider few of the difference  between the FET and the BJT are listed in the table.

Q: compares as points and try to make the answer short b) Explain the main differences between BJT…

A: In this question, we have to differentiate between BJT, MOSFET and IGBT..

Q: Explain the use of Metal Oxide Varistors MOVs

A: MOVs (Metal oxide varistors) is a variable resistor whose resistance is changed with respect to…

Q: Q2- Compare briefly between BJT and MOSFET. (In terms of characteristics, applications, merits and…

A: Comparision between BJT & MOSFET:

Q: 3) Draw the Input and output Characteristics of BJT for CB configuration

A:

Q: 1. Draw AM modulator Block Diagram 2. Draw all the signals 3. Write the equation for Modulating…

A:

Q: ) Differentiate between JFET and MOSFET transconductance curves

A:

Q: 4. What are the advantages of MOSFET over JFET?

A: Dear student please find the attachment.

Q: b) Design a MOSFET NOR circuit

A: MOSFET: Metal-oxide-semiconductor field-effect transistor (MOSFET) is an acronym for a…

Q: Q 2(a) Give three classifications of stability and give an example of each type. Q 2(b) How is…

A: Given :   Here in the question they want to know the classification of the stability of a system.…

Q: I want presentation about mosfet / Jft

A: It is needed to explain the basics about about MOSFET.

Q: How to use bjt to control mosfet as a switch with detailed circuit diagram

A: Bipolar junction transistor is act as a switch if it operates in cutoff and saturation mode of its…

Q: Draw the equivalent circuit model and switching characteristics of the device which is used for low…

A: MOSFET is a device which is used for low on state loss and high switching frequency operation.…

Q: Explain in broad the theory about Common Emitter Amplifier

A: A common emitter amplifier is the type of BJT configuration in which there are three terminal that…

Q: range of frequencies over which the VCO

A: PLL (Phase locked loop)- This is one which is used in broad range in communication circuit for…

Q: For the Depletion-type MOSFET n

A:

Q: The figure shows the AM modulated signal. What is

A:

Q: A BJT amplifier configuration in which the base is the common terminal to an ac signal or ground.

A:

Q: Q#1: Explain Bipolar Junction Transistor (BJT) also explain how BJT work as an Amplifier.

A: Introduction: A bipolar junction transistor, or BJT, is a solid-state device in which the amount of…

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.