f an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?

f an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 14RQ: The compressor amperage of a 3-ton system operating on 230 V is approximately -A.

See similar textbooks

Related questions

Q: Two Carnot engines A and B are operated in series between a high temperature reservoir at 1200…

A: Given Data QHA=600 kJ TH=1200 K TL=450 K

Q: n basic terms, briefly explain the following cycle 1. Topping

A: introduction: here we have to explain 1. Topping cycle 2. Incomplete expansion cycle 3. Binary cycle…

Q: Considering air standard values, calculate for the net work in HP given that the suction of the…

A: Given: Let us consider the given data, Volume flow rate=0.04 cfm Mass flow rate, m˙=62.43 lbmin…

Q: A four-cylinder gasoline engine has a cylinder diameter of 20 cm and a stroke of 40 cm. The…

Q: A diesel engine with a compression ratio of 14 is being designed such that the pressure and…

A: 956 K is the correct answer.

Q: A gas turbine power plant has specific heat ration of 0.72 with compression ratio of 0.12 Calculate…

A: Given: Specific heat ratio for gar turbine power plant→γ=0.72 And compression ratio →r=0.12 Because…

Q: A 1,500 six-cylinder 23- by 28-in. 225-rpm four-stroke diesel has a fuel consumption of 0.38 lb per…

A: Given data, Here some data is missing. Take cylinder's brake power as 1500 hp Brake power=1500…

Q: The % clearance of an Otto cycle is 0.186. If the initial pressure is 33 kPag, determine the final…

A: Given data: ● The clearance of an Otto cycle: C = 0.186 ● The initial pressure in the Otto cycle:…

Q: A Carnot engine operates between temperatures of 1000°K and 300°K. The engine operates at 2000…

A: Question belongs to subject IC ENGINE. Can be solved using formula's of carnot engine efficiency and…

Q: Represent the Carnot cycle as a square on the T-S plane. Now inscribe within the square of a circle…

A: Given question: Represent the Carnot cycle as a square on the T-S plane. Now inscribe within the…

Q: A single-acting, four cylinder, 4 stroke cycle diesel engine with a bore to stroke 21.59 cm x 27.94…

Q: A four-stroke gasoline engine runs at 1800 RPM with a total displacement of 3 L and a compression…

A: Given data: r=10k=1.4N=1800 rpmPm=600 kPaVd=3 L Need to determine the cycle efficiency and power…

Q: An Otto cycle has a clearance of 8 % and heat added of 1000 kJ. Find the heat rejected. ANSWER:…

A: Clearance= 8% Heat added, Qadded= 1000 kJ To find: Heat rejected, Qrejected

Q: It is required to feed an industrial ventilation system at a rate of Q = 23,000 ft3/min that demands…

Q: Determine the air standard efficiency of an engine operating on the diesel cycle when the suction…

Q: Which of the following is an example of an external irreversibility associated with a power plant?…

A: Irreversibility: It is the process in which heat is transferred through a finite temperature. It…

Q: he power requirement of a 3-stage compressor (in kW, two decimal places) in order to supply air at…

A: Given:T=20° CQ=250 m3/hrP=100 psig =689.47 KPaη=60%

Q: The name plate data of three-phase induction motor has the following data: 25 H.P., P= 4, 50 Hz, Y ,…

A: The given values are:…

Q: 13. In a steam turbine plant, the initial pressure and temperature of the steam are 3 MN/m² and…

A: P5=1MPaT5=20 Solution: Using steam table we will find the following state properties, At state 1…

Q: . just need the graph or figure of it. An air-standard Compression Ignition cycle has a compression…

Q: A Carnot engine requires 35 kW from the hot source. The engine produces 15 kW of power and the…

A: Given Heat supplied, QS = 35 kW Power produced, W = 15 kW Find Heat rejected, QR

Q: A generating unit of 10 MW capacity supplies the following loads: Domestic consumers with a maximum…

Q: An automobile engine consists of a number of pistons and cylinders. If a complete cycle of the…

A: Non flow process- the process in which no mass interaction across the boundaries of system during…

Q: kg/sec of steam enters the condenser at 0.12 mpa and 10% mosture. what should be the mass of the…

A: Given:ms=9 Kg/secP=0.12 MPax=0.10Ti=32°CTf=42°C

Q: n experimental UAV (or Unmanned Aerial Vehicle) is to be equipped with two engines with ideal cycle…

A: Given:η1=40%η2=95%W=1300 W-hrs

Q: In an oil engine working on dual combustion cycle the temperature and pressure at the beginning of…

A: Given: The dual cycle is shown below: P1=1 barT1=90°CV1V2=13 Total heat supplied is 1675 j/kg.

Q: An oil engine has a swept volume of 55 l and compression ratio of 12:1. The pressure and temperature…

A: Given dataSwept volume VS = 55L = 0.055m3Compression ratio r V1V2= 12:1Pressure P1 =…

Q: 2.) A room air conditioner has a coefficient of performance of 2.9 on a hot day and uses 850 W of…

A: Given, Electric work rate (Power) = W' = 850 W Coefficient of performance = COP = 2.9 Let us take…

Q: temperature of 800°C and pressure 12MPa. Calculate the network output in kW of an electric generator…

Q: A four-cylinder gasoline engine has a cylinder diameter of 20 cm and a stroke of 40 cm. The…

A: Given, Diameter of cylinder,D=20cm=0.20mLength of cylinder,L=40cm=0.40mSpeed, N=150rpmMean effective…

Q: A diesel cycle has a compression ratio of 8 and an initial temperature of 34oC. If the maximum…

Q: Problem No 1 A Carnot engine operates between temperatures of 1000°K and 300°K. The engine operates…

Q: Q 14. A two-stroke engine has a speed of 600 rpm. A four-stroke engine having an identical cylinder…

A: Keeping All the parameters constant Power out of engine is directly proportional to speed of…

Q: The conditions at the beginning of compression in an Otto engine operating on hot-air standard with…

A: Explanation: ,K=1.35 Clearance is 8%. Heat added=15 KJ We know that the compression ratio…

Q: A single stage double acting air compressor of 150KW power takes air in at 16 bar & delivers at 6…

A: Given: The power acting compressor, P = 150 kW The pressure at inlet of compressor, P1 = 16 bar The…

Q: Thermodynamic Properties of HFC-134a Refrigerant (1,1,1,2-tetrafluoroethane) CH2FCF3 molecular…

A: Case1: when the refrigerator is placed in household air, TH= 70°F= 294.26 K TC = 0°F= 255.372 K…

Q: A diesel engine has a bore of 0.1 m, a strike of 0.11 m, and a compression ratio of 19:1 running at…

A: Answer: Engine Power = 121 kW or 162 hp

Q: Gas is compressed in a reciprocating compressor from 33 kPa to 89 kPa. The FAD is 14 dm3/s. The…

Q: A diesel engine operating on an air standard condition has a net work output of 300kJ/kg if the heat…

Q: Determine the air-standard efficiency of an engine operating on the diesel cycle with a clearance of…

Q: If a diesel engine working on an air standard condition has a net work output of 300kJ/kg and the…

Q: The shop test of a single-acting, 8" x 12" engine whose record is hereby reported was made for the…

A: Excess air is given to combustion chambers to ensure full burning of the fuel. Excess air boosts the…

Q: What is the final temperature after compression of a Diesel cycle if the initial temperature is 32°C…

A: clearance ratio is the ratio of clearance volume to that of swept volume. Clearance volume is the…

Q: A diesel engine compresses air whose temperature is 27°C and pressure is 95 kPa. At the end of the…

Q: A nuclear-power station with a life of 25 years produces 750 MW per year as useful energy. The…

Q: A two-stroke, 12-cylinder diesel engine produces 2440 kW of effective power at 550 rpm. Since the…

Q: 24 - The specific volume of the refrigerant R-134a entering an adiabatic emitter is 0.028371 m³/kg…

A: The above question is a case of continuous flow of fluid which can easily be solved by using the…

Q: Temperature and pressure of air at the start of isentropic compression in a Dual Combustion Engine…

Question

100%

If an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A jet engine is bolted to a stationary test stand and run at full thrust. Air enters the engine at a rate of 80lbm/sec and fuel enters the engine at a rate of 0.8 lbm/sec. Additionally, the following values are known:Pinlet = 13 psi Pexhaust = 14.7 psiVinlet = 500 ft/sec Vexhaust = 1500 ft/secAinlet = 4 ft2 Aexhaust = 3 ft2Find the reaction force required to hold the engine in place on the test stand.
A steam turbogenerator delivers 750,000 KW when the steam flow is 2,250,000 kg./hr. Calculate the work done per kilogram of steam.
An 850 KW, 2-stroke, 6-cylinder diesel engine, 370 mm x 450 mm x 257 rpm uses 257 liters per hour of 24 deg API fuel at 21 C. The efficiency of the generator is 93%, while the mechanical-electrical efficiency is 90%. The indicated mean effective pressure is at 8.73 kg/cm?. Determine the following: a. Indicated thermal efficiency b. Plant thermal efficiency c. Brake fuel rate d. Indicated heat rate
4 Which of the following could not be the power coefficient of a slow speed wind turbine? a. 0.444 b. 0.3396 c. 0.327 d. 0.265
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
A geothermal power plant has a brake power of 20 MW, combined efficiency of 80%, and mechanical efficiency of 80%. The pressurized groundwater at 175 bar and 280 degrees Celsius leave the wells to enter the flash chamber maintained at 14 bar. The steam collected enters the turbine a 14 bar and exhaust at 1 atm. If one well discharges 180000 kg/hr of hot water, compute the combined work in kW.
Essay Topic: Define the following terms related to reciprocating engines: cycle, stroke, bore, clearance volume, volume displacement, clearance percentage, compression ratio, cut-off ratio, pressure ratio, and thermal efficiency.
A single-acting, four cylinder, 4 stroke cycle diesel engine with a bore to stroke 21.59 cm x 27.94 cm, operating at 275 rpm, consumes 8.189 kg/hr of fuel whose heating value is 43,961 kJ/kg. The indicated mean effective pressure is 475.7 kPa. The load on the brake arm, which is 93.98 cm is 113.4 kg. What is the brake arm mean effective pressure?
A geothermal power plant has a brake power of 20 MW, combined efficiency of 80%, and mechanical efficiency of 80%. The pressurized groundwater at 175 bar and 280 degrees Celsius leave the wells to enter the flash chamber maintained at 14 bar. The steam collected enters the turbine a 14 bar and exhaust at 1 atm. If one well discharges 180000 kg/hr of hot water, compute the number of wells required (IN WHOLE NUMBERS).
In basic terms, briefly explain the following cycle 1. Topping cycle 2. Incomplete expansion cycle 3. Binary cycle4. Otto cycle5. Diesel cycle 6. Brayton Cycle
5. If the power to drive shaft is 7.07PS and the mechanical efficiency is 74%, what is the actual compressor power? a. 9.46kW b. 5.18kW c. 5.18hp d. 9.46hp Please answer this immediately. Thank you!