n experimental UAV (or Unmanned Aerial Vehicle) is to be equipped with two engines with ideal cycle efficiency of 40% and 95%. The engine follows the fundamental principles/concepts of cyclic processes. Each engine is to be rated with 1300 Watts-hour of work developed. Determine (a) the heat supplied, (b) the ratio of heat supplied to heat rejected, and (c) the ratio of work developed to heat rejected on each engine.

Q: How can an SMA welding electrode’s flux help withdeeper penetration?

A: Shielded metal arc welding (SMAW) also known as stick welding, is a manual process using a flux…

Q: The Free-Body diagram for joint C is drawn assuming that all internal forces are in tension. Solve…

A: Given:W=2300 N

Q: What safety precautions should be observed when using layout tools that are used for scribing?

A: A scriber is a hand tool used in metal work,  to mark lines on workpieces, prior to machining. The…

Q: 4. 6.3 kg/s of oxygen undergoes a steady flow process. At inlet state, the reduced pressure is 2 and…

A: given; mass(m)=1.3kg/sinitial temperature(Tr1)=1.3exit reduced temperature(Tr2)=1.7Co=0.915Kj/kgk

Q: A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.1 mm to new position…

A:

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: 1. The engine's platform has a rectangular foundation cross-section of 15 x 4 m. The height of the…

A: Write the dimension of the rectangular foundation after considering clearance. b=15+20.75=16.5…

Q: For the system, determine the flow rate of oil coming out of the tank velocities and pressures at A…

A: GivenX=5.6mY=1.2m

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

A:

Q: Determine the final velocity of car Initial velocity=7 m/s Acceleration=2.22 m/s2 Time=5 s

A: Given data : Time t=5 s Initial velocity U=7 m/s Acceleration a=2.22 m/s2   Required : Final…

Q: Figure 3 show a tank with a U-tube manometer. Fluid A is oil with a relative density of 0,9. Fluid B…

A:

Q: 3.1 The sector sluice gate in figure 1 is installed at the outlet of a dam.The dam contains water…

A: Given: The width of the gate→w=1.8 m Radius of the sluice gate→R=0.75 m Because distance of the…

Q: homogenous block of weight W rests upon the incline as shown in figure below if the coefficient of…

A: Given:weight of block=WCoefficient of friction, μ=0.30

Q: An 8-m cantilever beam has a uniformly distributed load of 12 kN.m throughout its entire length and…

A:

Q: A mass-damper-spring what is the damping constant c? 00N s/m O 1250 N s/m O 50 N s/m O 25 N s/m…

A: Given Data- Mass m=5kg Stiffness k=125 N/m We have to find damping constant

Q: How much of a cold air stream at 18°C, 80% relative humidity should be mixed with 5.8 kg da/s of a…

A: Write the enthalpy at 18 oC and 80% Relative humidity. h1=44.22 kJ/kg Write the enthalpy at 35 oC…

Q: What can make welding in the 2G vertical fixed pipe position difficult?

A: The following is how the 2G welding positions are used. 1. Vertical position is used when using 2G…

Q: Prob. 3.3-2. The three-part axially loaded member in Fig. P3.3-2 consists of a tubular segment (1)…

A: Given: The outer diameter of tube 1, do1 = 1.25 in The inner diameter of tube 1, di1 = 0.875 in The…

Q: What is the first weld bead of a multiple pass weld called?

A: Root Pass  is the first weld bead placed in the weld joint in a multi-pass weld.

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

A:

Q: find omega ab and omega prime ab. Cylinder D rolls without slipping with an angular motion given as

A:

Q: Determine the mass of car having kinetic energy 2300 J moving with velcoity 77 m/s

A: Given data : Kinetic energy K.E=2300 J Velocity V=77 m/s   Required : Mass of car

Q: The flow rate through a 10-cm-diameter wrought iron pipe shown below is 0.04 m³/s. Find the…

A:

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: u = 2.3 mm, v = 3.9 mm c = 685 mm α =310, and β = 590 It is required to determine the…

Q: A thin flat plate is hanging on a string such that its top surface is exposed to a solar radiant…

A: Given:Heat flux, Q=800 W/m2heat transfer coefficient, h=21.1 W/m2.KT∞=39°C

Q: Problem #1 A student pushes the 1.25 kg block in the figure below against a horizontal spring,…

A:

Q: Q3) Determine the moment of the force about point O. show in Fig (3) Neglect the thickness of the…

A:

Q: Compute the efficiency of machine Input=870 J Output=600 J

A: Given data: Input=870 JOutput=600 J Need to determine the efficiency of the machine.

Q: What is the name of the flow when Mach number is one?

A:

Q: Prob. 3.6-10. The pipe-sleeve element (1) and cylindrical- rod core element (2) in Fig. P3.6-10 are…

A:

Q: Find the maximum shear stress in rectangular section if normal shear stress value is 22 Mpa

A:

Q: 1. Determine the force in members CD, CJ, and DJ. 401b B 8000 lb C D E 5001b L K . . . . . . . G 12

A:

Q: What is the magnitude and direction with respect to the positive x-axis of the force that should be…

A:

Q: Determine the final velocity of car Initial velocity=7 m/s Acceleration=2.22 m/s2

A:

Q: In the figure below, the flow velocity is 7.6 m/s. If d=10.1 cm and D=14.3 cm. Calculate the head…

A:

Q: find the head loss in the pipe using Darcy weishbach, manning and hazen Williams (remember to watch…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A:

Q: Evaluate the surface integral. /[(x + y + 2) ds, (x + y + z) ds, S is the parallelogram with…

A: Please refer to the detailed solution given below, Answer - Integral I = 405.96

Q: reate innovative ideas from the Prototyping & Robust Design concept for future product/service…

A: given; Prototyping & Robust Design concept for future product/service development.

Q: The wall of a building consists of a 360-mm thick layer A which has a thermal conductivity, kA - 4.9…

A:

Q: A mass-spring system has a natural period of vibration of T = double the mass m? OTn= √2 O Tn F O Tn…

A:

Q: In your experiment, you select one piece of metal and heat it to 100.0 °C, and then select a second…

A: Given data: One piece of metal is heated to 100°C  and another is cooled to -10°C The following are…

Q: Calculate the strain (e) for a change in length (ö) and a length (L), where 0 = 0.015 in and L = 5…

A: Given data: δ=0.015 inL=5 ft Need to determine the strain.

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

A:

Q: For the connection shown, the bolt diameter is d = 30 mm.  The average shear stress in the bolts…

A:

Q: In a shell-and-tube heat exchanger, water enters at 85°C at the rate of 5.4 kg/s. Engine oil enters…

A:

Q: Find the boiler heat transfer including the reheat process (kW)

A:

Q: power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It…

A:

Q: 5. Figure 3, below, shows a rollercoaster ride. The curve of the rollercoaster is given by the…

A:

Q: f) 500 kg of steam is at 2.0 MPa and 156°C. Determine the phase(s) of the steam present, the volume…

A: Given:m=500 KgPressure, P=2.0 MPaTemperature, T=156°C

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.