F ANALYSIS OF STRUCTURE The truss shown in the figure is loaded with forces at the joints of the truss. Compute the internal forces in the members DF, FG, FH and GH only. Indicate if the internal force is a Tension B = 200 KN 9 m 50 KN В A or a Compression. You can use Method of Joint or Method of Section. 4 m C 4 m E 4 m G 3 m 3 m 20 KN 20 KN 20 KN 20 KN

F ANALYSIS OF STRUCTURE The truss shown in the figure is loaded with forces at the joints of the truss. Compute the internal forces in the members DF, FG, FH and GH only. Indicate if the internal force is a Tension B = 200 KN 9 m 50 KN В A or a Compression. You can use Method of Joint or Method of Section. 4 m C 4 m E 4 m G 3 m 3 m 20 KN 20 KN 20 KN 20 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Frame ACGE is on hinge support at Aand E and braced at B and F to resistforce T = 18kN.a = 2 mb = 1 mc = 1 ma. Find the reaction at D in kN. b. Find the stress in brace BD if it ismade of pipe of ø = 75 mm andthickness = 6 mm. c. If brace AB is connected to BDconsist of two flat bars bolted topost AC at B using 20-mm-ø bolt,find the average shear stress (inMPa) in the bolt.
H.W (Equilibrium The bracket BCD is hinged at C at B For the loadiog shown, dee. (5) the seaction at € ; o . el o] Saim T et the rescions ¢ A st B when () = 0, () = 20w om0 = e Alight bar AB supports 15-kg Hock t s midpoint . Rollrs A and B ret against fctioubess suraces, and 3 borzonial cabe AD is atached at A. Determine (a) the tension i cable AD. 0 the reactions t A and B, (50 o ss0mn T cable CB is subjected 10 @ tension thal 15 twice that of cable CA, determine the angle 6 for equilibrium of the 10-kg cylinder. Also, what are the tensions in wires CA and cB For the structure shown find a) the tension in the string b) the reaction at A
A short spiral column carries an axial dead load of 118 kN and an axial live load of 235 kN. Use fc’ = 27.5 MPa, fy = 414 MPa. Use U = 1.2D + 1.6L, Ф = 0.65 1. Assuming ρ = 0.01, which of the following gives the diameter of the column section? * a. 200 mm b. 215 mm c. 220 mm d. 300 mm 2. Which of the following gives the number of 16 mm diameter main bars? a 3 pcs b. 4 pcs c. 5 pcs d. 6 pcs 3. Which of the following gives the spacing of spirals? a. 10 mm Ф b. 55 mm Ф c. 60 mm Ф d. 65 mm Ф
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
BADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)
13 - Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed support, the G point is the intermediate joint, and the B support is the sliding joint. Distributed loads on the beam q1= 9 kN ⁄ m, q2= 6 kN ⁄ m, beam dimensions a = 3 m, b = 2 m. Accordingly, Bx = ?a) 45B) 6C) None.D) 0E) 19.5
The Channel section is used as a purlin placed on top of trusses with spacing of 4.1 m and slope 1V to 4H. The purling are supporting a total uniform load of 20.2 kN/m.Properties of Channel:Sx = 119 × 10^3 mm^3Sy = 87 × 10^3 mm^3 Compute the maximum bending stress.Use NSCP 2015Round your answer to 2 decimal places.
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long, pinned at the top fixed at bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 1. calculate the nominal axial load capacity of the column a. 3104 kN b. 4851 kN c. 4213 kN d. 5344 kN 2. calculalte the service axial dead load if the service axial live load is twice as that of the dead load. Use LRFD. a. 1354 kN b. 992 kN c. 1093 kN d. 634 kN
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
For the given loads F1=42 KN, F2=48 KN, F3=45 KN, F4=32 KN (Assume internal forces are in tension) 1- Magnitude of reaction at K is (KN) :(a. 151 - b. 226.5 - c. 302 - d. 377.5 - e. 453 ) 2- internal force in member JH (KN) :(a. -327 - b. -218 - c. -436 - d. -545 - e. -654) 3- internal force in member IH (KN) : (a. -204.600222 - b. -136.400148 - c. -272.800296 - d. -341.00037 - e. -409.200444 ) 4- Magnitude of reaction at A is (KN) 5- internal force in member IK (KN) is 6- internal force in member GF (KN)
Design the spacing of the main bars and temperature bars of a one-way slabhaving a total span of 5 m. The slab is supported with hinge in the left support anda vertical cable located 1.5 m from the right support. The distance between thecables of the slab is 2.3 m. The slab is to carry a live load pressure of 2.4 kPa anda dead load pressure (including self-weight) of 4 kPa. Assume f’c = 27.6 MPa andfy = 276 MPa for main and temperature bars. Use 12 mm ∅ for main bars and 10mm ∅ for temperature bars. The slab is not exposed to earth or weather. Usethickness of slab of 120 mm. Use NSCP 2001.
The frame is used to support the wood deck in a residential dwelling. Sketch the loading that acts along the members BG and ABCD. Set b=4.5m, a=2.4m. Use Live Load=1.92 kPa.