A one way slab having a simple span of 4.0 m has a thickness of 150mm. The slab is reinforced with 12mm tension bars with fy = 275 MPa spaced and clear spacing of 212mm. Clear concrete cover is 20mm. Use f'c = 21 MPa and unit weight of concrete 23.5 kN/m'. a. Determine the Coefficient of Moment Resistance. b. Determine the moment capacity of the slab. c. Calculate the uniform live load pressure that the slab can carry.

A one way slab having a simple span of 4.0 m has a thickness of 150mm. The slab is reinforced with 12mm tension bars with fy = 275 MPa spaced and clear spacing of 212mm. Clear concrete cover is 20mm. Use f'c = 21 MPa and unit weight of concrete 23.5 kN/m'. a. Determine the Coefficient of Moment Resistance. b. Determine the moment capacity of the slab. c. Calculate the uniform live load pressure that the slab can carry.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular doubly-reinforced beam 450 mm wide and reinforced by 5-32mm diameter bars for tension and 3-28 mm diameter bars for compression and has the following properties: (NSCP 2010) d = 650 mm d’ = 70 mm f’c = 20.7 MPa fy = 344.80 MPa a. Find the depth of compression block. b. Find the ultimate moment capacity of the beam.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A rectangular beam of length 702mm has a width of 132mm and a depth of301mm. Compression steel bars are placed at a distance 98 mm from the extreme concrete compressivefiber. The beam supports service dead loads of dead load (16 KN/m) and live load (24 KN/m). Reinforced with 4 25mm tension steel bars and 4 12mm tension steel bars f′c = 42 MPafy = 519 MPa 1. Solve for the height of the neutral axis measured from the extreme compression fiber.2. Solve for the design moment.3. Solve for the strength reduction factor.
A rectangular concrete beam 400 mm wide and effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f'c= 21 MPa and steel yield strength fy = 275 MPa.a. Determine the depth of the rectangular compression stress block.b. Determine the ultimate moment capacity of the beam.
Refer to the figure below.The square steel tube carries 100kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 1000 N.
The three stone blocks have weights of WA = 600 lb, WB = 150 lb, and WC = 500 lb. Determine the smallest horizontal force P that must be applied to block C in order to move this block. The coefficient of static friction between the blocks is 0.3 and between the floor and each block 0.5.
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m, 1. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa 2. Compute the bending stress of the beam. a. 56.33 MPa b. 71.11 MPa c. 78.48 MPa d. 45.78 MPa
Determine the reversed horizontal force −P needed to pull out wedge A. The coefficient of static friction between A and C and between B and D is μs = 0.2, and between A and B μ's = 0.1. Neglect the weight of each wedge.
4. A concrete beam of rectangular section 200 mm wide and 600 mm deep, is prestressed by a parabolic cable located at an eccentricity of 100 mm at midspan and zero at the supports. If the beam has a span of 10 m and carries a uniformly distributed live load of 4 kN/m, find the effective force necessary in the cable for zero shear stress at the support section. For this condition, calculate the principal stresses. The density of concrete is 24 kN/m3.
A W460×60 steel beam is loaded as shown. Assume w = 40 kN/m, M0 = 60 kN·m, LAB = 3.9 m, LBC = 1.6 m, E = 200 GPa, and I = 255 x 106 mm4.(a) Determine the reaction force at roller B.(b) Determine the maximum positive bending moment in the span.(c) If the allowable bending stress is 210 MPa, determine the minimum acceptable section modulus for the steel beam. Remove roller B. Determine the deflection at point B caused by the distributed load vw and by the moment vMo. Upward deflection is positive.Answer:vw = mmvMo = mm
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
Determine the maximum force P in kips that the reinforced concrete column can support. ??? = 30,000 ??? and ?? = 4,000 ???. The radius of steel rods is 0.5 inch. The allowable stress of steel is 10 ksi while that of concrete is 4.5 ksi.