F4 ft 4 ft (ksi) 5 ft 36 B (in./in.) 0.0012 0.2

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A: Given data: F=600 Ndi=25 mmt=5 mm Need to determine the maximum shear stress in the tube.

Q: the natural strain at point B (ɛg

A: Given data; The true stress ,true strain diagram of a strain  hardening material shown in fig,…

Q: If a horizontal load applied to the bar AC causes point A to be displaced to the right by an amount…

A: From the above figure length of the wire, LAB is calculated as:

Q: Determine the shear strain developed in the shear plane of the bolt when P = 340 kN .

A: Given that: diameter of the bolt = 33 mm Load = P = 340 kN It is required to determine shear strain…

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A: Given : εx = -1100 με εy = 490 με γxy = 1500 μrad θ  = 34°

Q: a3) Determine the shear strain at corner D and the normal strain of the diagonal CA if the shape is…

A: Shear strain is the strain caused due to the applied force in the longitudinal direction.

Q: The beam is made of phenolic, a structural plastic, that has the stress–strain curve shown. If a…

A: Given data To determine the magnitude of uniformly distributed load in the section for not to…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A: From triangle ABP, The expression to calculate the length of line AB is, Substitute values in the…

Q: The cable has a specific weight g (weight/volume) and cross-sectional area A. Assuming the sag s is…

A: Given Data: Weight per volume of the cable is: g (weight/Volume)

Q: The rubber band AB has an unstretched length of 1m. If it is fixed at B and attached to the surfaced…

A:

Q: The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: for pt B  BD = AB*tan2o        = 3*0.0349        = 0.1047 m normal strain in wire BD will be

Q: The fiber AB has a length L and orientation u. If its ends A and B undergo very small displacements…

A: Given Length of the fiber L To find The normal strain

Q: The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading…

A: Represent linearly varying load on diagram Take a section at x from left and load can be calculated…

Q: The pin-connected rigid rods AB and BC are inclined at u = 30° when they are unloaded. When the…

A:

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: The wire AB is unstretched when u = 45°. If a load is applied to the bar AC, which causes u to…

A:

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. 800…

A: Given Data : CB is rigid member having length L= 800mm AB is flexible cable distance AC = 600mm…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN,…

A:

Q: Q3 The beam has a rectangular cross section and is made of and elastic-plastic material having a…

A: Stress: The restoring force per unit area of the material  is known as  stress. It is a tensor…

Q: A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10…

A:

Q: The circular punch B exerts a force of 2 kN on the top of the plate A. Determine the average shear…

A: Given data The load exerted by punch B on the plate, V = 2 kN. The diameter of punch B, DB = 4 mm.…

Q: 1. The intensity of the shear stress distribution acting over the cross sectional area needs to be…

A:

Q: he center portion of the rubber balloon has a diameter of d 100 mm. If the air lessure within it…

A: Given data : original diameter=100 mmfinal diameter=125 mm

Q: If the load P on the beam causes the end C to be displaced 10 mm downward, determine the normal…

A: Given Data: The displacement of point C under the load P is d= 10 mm. The length of cord BD and CE…

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A: The diagram of the triangular plate is given as,       The distance OA is written as,…

Q: 3. The rectangular plate is subjected to the deformation shown by the dashed line. Determine the…

A:

Q: The steel rod has a circular cross section. If it is loaded by a 500 lb vertical force as shown,…

A:

Q: The rectangular plate is subjected to the deformation shown by the dashed line. Determine the…

A: Draw the diagram showing the angle deformed by the plate.

Q: Q3: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown,…

A: Answer:Step 1:Given data: width of plate =b=0.5m                       length of pipe ,  l=4mto find…

Q: Part of a control linkage for an airplane consists of a rigid member CBD and a flexible cable AB. If…

A: According to the information, we have a control linkage with rigid member CBD and a flexible cable…

Q: The piece of plastic is originally rectangular. Determine the average normal strain that occurs…

A: The dimensions of the rectangular box are given as the:

Q: The square plate is such that L = 273 mm. The corners of the square plate are given the…

A: Shear strain is the change in angle between two  rad surfaces at that point.

Q: (a) the strain in the cable at a depth of 700 ft. (b) the total elongation of the cable.

A:

Q: The nonuniform loading causes a normal strain in the shaft that can be expressed as Px = k sin ap L…

A: Given: Strain at any section is given as,εx=ksinπxL The schematics of a point at the section is…

Q: Consider the wooden member subjected to a tensile load P = 11.0 kN. Determine the magnitude of the…

A:

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: For the F.B.D of the shaft. For the equilibrium of the shaft in horizontal direction.

Q: 2. The piece of plastic is originally rectangular. Determine, a. the shear strain Y.y at corners A…

A: Using trigonometry relation

Q: Determine the resultant internal loadings acting on the cross-section of the frame at points F and…

A: Given data: Three links are attached together. Determine:  The resultant acting on the cross-section…

Q: The triangular plate is deformed into the shape shown by the dashed line. Determine the normal…

A: Coordinates of point                 A=0,0 B=400,0C=0,-300D=405,-3   Distance B-C using Pythagorean…

Q: Determine the shear strain gxy at corners A and B if the plastic distorts as shown by the dashed…

A: Draw the figure representing the angles α, β, and ϕ.

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

A:

Q: 1.The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: Given data as per question Distance between A and B =200 mm Distance between A and H =200 mm…

Q: The strain at point A on the bracket has normal components 750x106 and 150x106 in x and y…

A:

Q: An elastic block of equal side lengths is deformed into the shape shown by the dashed lines.…

A: Given-Data:- Side of square=50mm To-Find:- 1) Shear strain at A 2) Shear strain at C

Q: Please find the question attached.

A: Given data as per question

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: Draw free body diagram of the right segment of the bar sectioned at x. Considering the equilibrium…

Q: Determine the resultant internal loadings acting on the cross-section at B ofthe pipe shown in Fig.…

A: Free body diagram of part 'AB' of the pipe is taken in to account here. So, load acting at 'A' in…

Q: 6. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L…

A:

Q: The board is subjected to a tensile force of 200 lb. Determine the average normal and average shear…

A: The magnitude of the tensile force is, W=200 lb The orientation of the plane is, θ=20° The breadth…

Q: (a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b)…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.