y 12 mm 4 mm 8 mm 3 mm в 300 mm 72 mm х D |A -400 mm- 5 mm

Q: 3. The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear…

A:

Q: If a horizontal load applied to the bar AC causes point A to be displaced to the right by an amount…

A: From the above figure length of the wire, LAB is calculated as:

Q: ven the stress tensor Го 0. 0 200 0 0. 0. 0. Determine the normal stress on plane ABC whose normal…

A:

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

A: Given data To determine the average normal strain along with diagonal AC, and the average shear…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A: From triangle ABP, The expression to calculate the length of line AB is, Substitute values in the…

Q: The following piece is originally rectangular Determine the average normal strain that occurs along…

A: Consider the diagram of the given figure with proper dimensions as shown below, From the diagram…

Q: 2-11. Determine the plastic distorts as shown by the dashed lines. 3 mm y C 300 mm the shear strain…

A:

Q: The rubber band AB has an unstretched length of 1m. If it is fixed at B and attached to the surfaced…

A:

Q: If the plate distorts as shown by the dashed lines, determine (a) the shear strain Ym at corners C…

A: Find shear strain at point C and D Normal strain along diagonals AC and BD

Q: Determine the bending strain energy in the 2-in.- diameter A-36 steel rod.

A:

Q: The strain rosette shown can be used to directly measure the in-plane shear strain Yxy- b 120° 60° а…

A: The strain gauge is defined as a measuring instrument used to encounter the strain directly. The…

Q: The fiber AB has a length L and orientation u. If its ends A and B undergo very small displacements…

A: Given Length of the fiber L To find The normal strain

Q: The material distorts into the dashed position shown, where d = 10 mm. d 2d D 50 mm B 200 mm EI 50…

A:

Q: The plate is deformed into the shape shown by the dashed lines. Determine the average normal strain…

A:

Q: The stress vectors acting on the three coordinate planes are given by te, te and tes'. Show that the…

A: Given, Stress vectors acting on 3 cordinate planes s = ti(e^1) ti(e^1) + ti(e^2) ti(e^2) + ti(e^3)…

Q: F7-25. When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: The normal strain of the wire CD = change in the length of wired CD/Initial length of CD. The given…

Q: Q3/ The material distorts into the dashed position shown in fig.2. Determine the average normal…

A:

Q: The wire AB is unstretched when u = 45°. If a load is applied to the bar AC, which causes u to…

A:

Q: The strain at point A on the bracket has normal components 300x106 and 440x106 in x and y…

A: GIven data: The strain along x-axis is εx=300×10-6 The strain along y-axis is εy=440×10-6 The shear…

Q: If the force P causes the rigid arm ABC to rotate clockwise about pin A through an angle of 0.02°,…

A: Given data: Rotated angle, θ = 0.020 Drawing the rotation of the arm ABC: here, δB = displacement…

Q: The undeformed length of the bar is 300mm. It is subjected to a Shear Strain Defined by; y = kx (y…

A: Given data: The length of the bar is, L=300 mm. The expression of shear strain is, γ=kx. Write the…

Q: A square piece of material is deformed into the dashed position. -15.18 mm В 15.24 mm 15 mm 89.7° A-…

A: Shear strain and average normal strain diagonal AC.

Q: If a rubber material is deformed as shown in the following figure, determine the normal strain along…

A:

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

A:

Q: 1. The intensity of the shear stress distribution acting over the cross sectional area needs to be…

A:

Q: he center portion of the rubber balloon has a diameter of d 100 mm. If the air lessure within it…

A: Given data : original diameter=100 mmfinal diameter=125 mm

Q: If a rubber material is deformed as shown in the following figure, determine the normal strain along…

A: As,  ∈x=320=0.15&, ∈y=-220=-0.1

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A: The diagram of the triangular plate is given as,       The distance OA is written as,…

Q: If a rubber material is deformed as shown in the following figure, determine the normal strain along…

A:

Q: 3. The rectangular plate is subjected to the deformation shown by the dashed line. Determine the…

A:

Q: Determine the normal strain across line AB b.)Determine average shear strains at corners C and D…

A:

Q: The rectangular plate is subjected to the deformation shown by the dashed line. Determine the…

A: Draw the diagram showing the angle deformed by the plate.

Q: The piece of plastic is originally rectangular. Determine the average normal strain that occurs…

A: The dimensions of the rectangular box are given as the:

Q: The square plate is such that L = 273 mm. The corners of the square plate are given the…

A: Shear strain is the change in angle between two  rad surfaces at that point.

Q: 1.The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: Draw the diagram in that the lever is rotated by 2 degrees clockwise.

Q: . A loading causes the member to deform into the dashed shape. Explain how to determine the normal…

A:

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A:

Q: Question 3 If e and e2 have the same signs., then the absolute maximum shear strain will be equal to…

A: To determine whether te given statement is TRUE or FALSE.

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A:

Q: Which of the following has no unit O strain

A: Ans: Strain

Q: The material distorts into the dashed position shown. Determine the average normal strains along…

A: Draw the schematic diagram of the given fig.

Q: 2. The piece of plastic is originally rectangular. Determine, a. the shear strain Y.y at corners A…

A: Using trigonometry relation

Q: The strain at point A on the bracket has normal components 750x106 and 150x106 in x and y…

A:

Q: . The intensity of the shear stress distribution acting over the cross sectional area needs to be…

A: Draw shear stress distribution over cross section.

Q: An elastic block of equal side lengths is deformed into the shape shown by the dashed lines.…

A: Given-Data:- Side of square=50mm To-Find:- 1) Shear strain at A 2) Shear strain at C

Q: Please find the question attached.

A: Given data as per question

Q: The two wires are connectec at A. If the force P causes point A to be dsplaced horizontally 2 mm,…

A: To determine the normal strain in each wire.

Q: When a tensile load applied on a metal of 10 mm diameter, the change in diameter is found to be 2.5…

A: Given, Diameter of metal, d=10mm Change in diameter, ∆d=2.5mm Whenever a load is applied on a…

Q: (a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b)…

A: