4. Calculate three phase voltages and currents at fault location andat Bus G for a phase-A to Ground (L-G) fault at bus H, for a systemas shown in Figure 2. Also draw the positive, negative, zerosequencenetworksand theirinterconnection diagram for thisparticular fault.90 MVA90 MVA132kVH132kVLine sectionSourceSourceB100 MVA100 MVA132/69 kV10%132/69 kV10%Figure - 2

Answered: fault location

Engineering

Electrical Engineering

fault location

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.28P

See similar textbooks

Related questions

Q: A three-anode mercury-arc rectifier supplies a 250-kw 230-volt load and is energized from a 4,600-vo...

Q: Refer to Figure below, determine v(t) and i(t). 4 2 + v, = 5 cos(10t) 0.2 H

A: Given circuit:

Q: A multiplexer is a device that selects one among N analog or digital inputs and forwards the selecte...

Q: A three phase star connected voltage source has line voltage of 415V and the frequency 50 Hz. This s...

A: Star system: If we connect the three terminals of three winding together. Condition is that connect ...

Q: 2. The base terminal of one NPN transistor is connected to N-type doping area or P-type doping area?...

A: 2 . In a NPN transistor Collector - N type doping area Base - P type doping are...

Q: Two conductors carrying 60 A and 75 A, respectively are placed 10 cm apart. Find the force between t...

Q: o18 V 4.7 k2 R1 Ic oVc = 12 VB o VE 5.6 k2 1.2 kM 1.60 V

Q: Assume, there was a daily cost of 10 cents/day per kW for the mitigation (repair) of the total envir...

A: Given that daily cost=10cent/day-kW

Q: 7. Use Kirchhoff's current law to determine the magnitudes and directions of the indicated currents ...

Q: My pofessor gave me a task, i need to write discription of image in step by step manner. kindly help...

A: It is asked to write description of image in step by step manner. In step 1 we need to write a short...

Q: 4.48 Determine the Norton equivalent at terminals a-b for the circuit in Fig. 4.115. 10i, 2Ω Mwo a 2...

Q: Identify whether the following are linear and time-invariant. Show proofs. 1.) y(t)=x(3t+2) 2.) y[n]...

Q: Which IC technology has the lowest power dissipation in general?

Q: Ohm's Law states that: Voltage = current x resistance Voltage = current / resistance Current = volta...

Q: RL 4. Suppose one NPN transistor is working under activation region, and Ip=0.005A. 12 What's the va...

Q: Three identical capacitors are connected in delta to a 408 V, 50Hz, 3-phase supply. If the line curr...

Q: The sequential circuits consist of a combinational circuit and storage elements. b The storage elem...

A: yes it is TRUE a) The sequential circuits consist of a a combinational circuit and storage elements...

Q: A 3-phase, 60 Hz, 30 km long overhead line supplies 400 kW at 11 kV, 0.9 p.f. lagging. The line resi...

A: Short transmission line An effective length less than 80km is known as a short transmission line. It...

Q: o18 V 4.7 k2 Ic R1 OVc = 12 V %3D VB VE 5.6 kN 1.2 kN

Q: Find current I, in the following circuit using the phasor approach, if Z= 40 0, Z2= j30 0, Zg= 40 0,...

A: Given circuit, where, Vs=100∠20° VZ1=40 ΩZ2=j30 ΩZ3=40 ΩZ4=-j30 Ω

Q: Two straight parallel wires 5 m long and 2 mm apart carries currents of 8 A in opposite direction. F...

Q: b) Obtain the transfer function of the system using Mason's rule where the signal flow graph is show...

Q: Vcc Ic 2.2 k2 RB + VCE = 7.2 V B IB = 20 µA %3D lg = 4 mA

Q: Subject: Electrical Apparatus and Devices The percentage resistance and reactance of a transformer a...

A: The solution is given below

Q: 2.4-2 Evaluate the following integrals: (c) L, 8(t)e-lut dt (d) S, 8(t – 2) sin at dt (g) , g(2 – t)...

Q: Reducing F = IABC + A/BC + AB/C + ABC would result in the equation: %3D Select one: Оа. АВ + вс + AC...

Q: Two straight parallel wires 5 m long and 2 mm apart carries currents of 8 A in opposite direction. F...

Q: Question: A logic circuit has 4 inputs and an output. The Output will be high for binary input combi...

Q: A 400V, 3-phase Induction motor has input power of 12 KW and operates at power factor of 0.87 laggin...

A: Let W1 be one wattmeter reading and W2 be another wattmeter reading. Input power W1+W2. Reactive po...

Q: Load Current Voltage

A: Given a DC motor-generator set whose supply is given to the motor and the output mechanical energy i...

Q: 4.47.3 In the circuit shown in the image below, if R1 = 38 Q, R2 = 37 Q, and l1 A, determine the Nor...

A: Given circuit, Where, R1=38 ΩR2=37 ΩI1=1.9 A

Q: The three-phase balanced load in the figure below has impedance per phase of Zy =6 + 8j ohm. If the ...

A: Given, ZY=6+8j ΩVL=220 V

Q: Q12: A. Explain the relation between current and voltage in the basic component of electrical circui...

A: Answer (A): The basic components of electrical circuits are, Resistor (R), Inductor (L), and capacit...

Q: 1. For the circuit shown below, a. determine the current I, by the nodal analysis. 12 2 3Ω 24 V 15 V

Q: bl 3 Q2/(b) Find Vo for the network shown * below =3 V - 10 ka 5 k2 10 kN 1 k2 10 k2 Vo 10 kn V;=1V ...

Q: Ge is operating at room temperature (i)Calculate the raion of forward current at 0.22 V and 0.2 V (i...

Q: R1 Sie R2 b In the circuit above, R1 is 35 n and R2 is 30 0. What is the equivalent resistance betwe...

A: Given data: R1=35 ΩR2=30 Ω

Q: A solenoid 30 cm long is wound with 300 turns. What is the value of its Field strength inside the so...

Q: Exercise Exercise Given a (7 , 4) non-systematic code [0 1 0 0 1 1 1 10 0 1 1 0 G = 0 1 1 0 1 1 1 0 ...

A: we have given a (7,4) non systematic code0100101100110110110001101011

Q: A-phase to ground fault

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase li...

Q: Find the wave impedance for the dominant mode in an air filled rectangular waveguide of dimension 8 ...

Q: 3. The antenna used for sky wave propagation is elevated at an angle of 30 degrees. Find the MUF if ...

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any ...

Q: Please write the RISC-V assembly instructions that create the 32-bit constant Ox23453456 and store t...

A: ASSEMBLY LANGUAGE INSTRUCTIONS: ADDI : This instruction modifies the contents of the source register...

Q: 20 μA '2.7 k Ω RB + VCE =7.3 V %3D o 2.1 V 0.68 kΩ

Q: na certain conducting region H = yz(x² + y²)a, у?xzа, + 4x?у?a, A/m. a) Determine J at (7, -1, 3) ) ...

A: The solution is given below.

Q: Which type of controller mode builds up corrective action proportional to the length of time the dis...

A: Controller mode- The method used by the controller to correct the error mode control. The four most ...

Q: Q3: Find F.T of the pulse sine wave shown in fig. below:

A: It is given that:

Q: Vcc 20 µA 2.7 k 2 RB VCE =7.3 V %3D o 2.1 V 0.68 kN

Q: 4.39 In the circuit shown in the image below, if R1 = 26 Q, V1 = 43 V, and /4 = 6.0 A, determine the...

Q: Find the transfer function, G(s) = V(s)/V(s), for the network shown in the figure below. 1 H vị(t) Ι...

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

100%

4. Calculate three phase voltages and currents at fault location and
at Bus G for a phase-A to Ground (L-G) fault at bus H, for a system
as shown in Figure 2. Also draw the positive, negative, zero
sequence
networks
and their
interconnection diagram for this
particular fault.
90 MVA
90 MVA
132kV
H
132kV
Line section
Source
Source
B
100 MVA
100 MVA
132/69 kV
10%
132/69 kV
10%
Figure - 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Equipment ratings for the four-bus power system shown in Figure 7.14 are as follows: Generator G1: 500 MVA, 13.8 kV, X=0.20 per unit Generator G2: 750 MVA, 18 kV, X=0.18 per unit Generator G3: 1000 MVA, 20 kV, X=0.17 per unit Transformer T1: 500 MVA, 13.8/500YkV,X=0.12 per unit Transformer T2: 750 MVA, 18/500YkV,X=0.10 per unit Transformer T3: 1000Â MVA, 20/500YkV,X=0.10 per unit A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault load current is neglected. Draw the positive-sequence reactance diagram in per unit on a 1000-MVA, 20-kV base in the zone of generator G3. Determine (a) the ThĂ©venin reactance in per unit at the fault, (b) the subtransient fault current in per unit and in kA rms, and (c) contributions to the fault current from generator G1 and from line 1-2.
A three-phase circuit breaker has a 15.5-kV rated maximum voltage, 9.0-kA rated short-circuit current, and a 2.50-rated voltage range factor. (a) Determine the symmetrical interrupting capability at 10-kV and 5-kV operating voltages. (b) Can this breaker be safely installed at a three-phase bus where the symmetrical fault current is 10 kA, the operating voltage is 13.8 k V, and the (X/R) ratio is 12?
Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit on a 100-MVA base are given as follows: The neutral of each generator is grounded through a current-limiting reactor of 0.08333 per unit on a 100-MVA base. All transformer neutrals are solidly grounded. The generators are operating no-load at their rated voltages and rated frequency with their ENIFs in phase. Determine the fault current for a balanced three-phase fault at bus 3 through a fault impedance ZF=0.1 per unit on a 100-MVA base. Neglect -Y phase shifts.
For the system of Problem 9.13, compute the fault current for the following faults at bus 3: (a) a single line-to-ground fault through a fault impedance ZF=j0.1 per unit, (b) a line-to-line fault through a fault impedance ZF=j0.1 per unit, (c) a double line-to-ground fault through a common fault impedance to ground ZF=j0.1 per unit.
b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the network are of 1 + j0 p.u, and the impedance of the electric arc is neglected (Zf = 0 + j0 p.u.). The positive, negative and zero sequence impedance parameters of the generator, transmission lines and transformer are given in Figure Q3. (i) Determine the positive sequence fault current for the case when a three-phase-to-ground fault occurs at bus 4 of the network (ii) Determine the short-circuit fault current for the case when a one-phase- to-ground fault occurs at bus 4. Recall that phasors can be expressed in terms of their symmetrical components as shown in the picture attached. where F stands for any three-phase quantity (e.g., current, voltage) (iii) Determine the short-circuit fault current for the case when a phase-to-phase fault occurs at bus 4 ReplyForward
At a 220 kV substation of a power system, it is given that the three-phase fault level is 4000 MVA and single-line to ground fault level is 5000 MVA. Neglecting the resistance and the shunt susceptances of the system, (B) And the zero sequence driving point reactance at the bus is: (@)2.2Q (b) 4.84Q (€)18.18 Q (d)22.72Q