Fi = 549 lb F2= 839 lb F - 806 lb and has the following geometry: w- 20 ft F2 F1 F3 B
Q: Determine the moment about point B for each of the individual three forces acting on the beam, and i...
A:
Q: 27. What method of DC series motor speed control is in the figure below? eles Field Diverter Armatur...
A: In the figure, the method of DC series motor speed control is paralleling field coil.
Q: 8. A 2500 kg van accelerates down an icy driveway, going from rest to 30.0 m/s in 6.00 s. During its...
A:
Q: As shown in figure below, a 100 lb body moves along the two inclines for which the coefficient of fr...
A:
Q: ASTM grain size for a metal was 3. Determine the number of grains at a section from its surface with...
A: Given Data The grain size of the metal was: G=3 The formula which is used for the ASTM grain size nu...
Q: oil (0.88) ► oil (0.88) Hg (SG=13. 320mm-
A:
Q: 10–3. Determine the moment of inertia of the area about the x axis. *10–4. Determine the moment of i...
A:
Q: The following data refers to a aboratory experiment with rope preak. Diameter of the flywheel = 1 m,...
A:
Q: Assume the field distribution produced by the stator in the machine shown in Figure P6.1 to be radia...
A: Given-Machine radialy uniform magnitude the air gap flux density=BSRotational speed=ωnRotor length=l...
Q: Why cascade system is the best choice for the above solution
A: A system or technique for connecting and running two induction motors so that the primary circuit...
Q: The horizontal pump in Fig.1 discharges water at 57 m3/h. Neglecting Losses,What power in KW is deli...
A:
Q: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe. I...
A: Given Velocity, V = 82 ft/s Diameter, d = 2 in = 0.166 ft Find Flow rate
Q: Q11/ To heat treat alloy rods, these are placed in a gas stream at 800°C with a convective heat tran...
A:
Q: A helical gear has a normal diametral pitch of 24, a normal pressure angle of14 14,°. 72 teeth, a fa...
A:
Q: Steam enters a nozzle at a pressure of 7 bar and 200°C (i.e. initial enthalpy 2850 kJ/kg) and a pres...
A: Given that, p1=7 bar=700 kPa,T1=200°C=200+273=473 K,h1=2850 kJ/kg, p2=1.5 barC1=40 m/s, C2=700 m/sm...
Q: A compressor was used to compressed air from initial conditions of 185 kPa and 326.85 K to final con...
A:
Q: A gear has 44 teeth of the 20°, full-depth, involute form and a diametral pitch of 12. Compute the ...
A:
Q: A triangular window, with its top edge horizontal, is built in the side of a water tank. The window ...
A: Height of the window, H= 16 m Width of the window, B= 8 m Maximum force that a be hod by the window,...
Q: A long – shunt compound generator delivers a load current of 50A at 500V and has armature, series fi...
A: Sol^n - The shunt field current - 500/250 = 2A Hence armature current Ia= IL+Ish ...
Q: 60° ) = 8 rad/s 500 mm a = 16 rad/s? 150 mm B 30°
A:
Q: 1. How would the plot of efficiency versus To-T/G, look like? Il What are the performance characteri...
A: Solution: Given Data: A=2 m2Tc=12oCGt=900 W/m2
Q: It is desired to develop a total power 223,800 kW in a hydroelectric plant under a head of 15 m and ...
A: Giventotal power requires to developP=223800kWH=15mN=60rpmNs=80 rpm
Q: What is the Effective Hanging Mass of th spring? Hanging mass = .01kg Position of Coil = .6375m peri...
A: Given data,hanging mass=0.01 kg =m3useing the relation-effective mass of spring =13×mass of spring
Q: Suppose the rated speed of a highway curve of 300 ft. radius is 40mph. If the coefficient of frictio...
A:
Q: Determine the single uniformly distributed load in the x direction that wo produce the same deformat...
A:
Q: The MDF sheet shown in the figure below iscut by a laser pointer, which moves through the curved gro...
A: Given data: The distance measured along the slot can be given by the expression:s=9t2– 2t The veloci...
Q: (a) (i) A reservoir has been built 4 kilometers away from TTU campus having 5000 inhabitants. Water ...
A:
Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to d...
A: Solution: Given Data: P1=200 psiaL=4 ftD=2 in Note: Po=600 psia
Q: 8.9 The stresses across two mutually perpendicular planes at a point in an elastic body are 120 MN/m...
A:
Q: BRAJ - TECH Manufacturing company requested AAA Power Plant to provide 1.08 MW as the maxirmum load ...
A:
Q: Problem 1: The pulleys are frictionless and of negligible weight A 250 kg 300 kg| C 450 kg Find: 1.1...
A:
Q: 1. If the pulleys. veightless and frictionless, find the acceleration of body 100 kg A 150 kg B
A:
Q: The reel of rope has the angular velocity w = 4 rad/s and angular acceleration a = 7 rad/s? . (Figur...
A: Givenω=4rad/sα=7rad/s2
Q: 72. KN/m 54 KN 90 KN し↓de 270 KN-mD A RI - zm - E 2m + 2m t imt zm 3m R2
A: Given Data: Length of the beam, L=12 m
Q: 2. A 210 kg motorcycle accelerates from 0 to 50 mi /hr in 5.0 s. (a) What is the magnitude of the mo...
A:
Q: 2.If the pulleys are weightless and frictionless, determine the acceleration of each weight. C 45 kg...
A:
Q: Mass M1 = 2.25 kg is at the end of a rope that is 2.00 m in length. The initial angle with respect t...
A: (a).
Q: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, whi...
A:
Q: When heat is added to a system, the amount of heat added can increase the temperature. increas...
A: Different types of thermal processes are: Isobaric process (constant pressure) Isovolumetric proces...
Q: The channel section shown is subjected to a vertical shear force of V = 20 kN. Calculate the horizon...
A: When a structure, such as a beam, is subjected to a transverse shear force, the bending normal stres...
Q: An arow Islauinched at height, and the tme it takes to reach this height Answer: h= 134.78 m, Provid...
A:
Q: 1. Determine the maximum speed that the cars of the roller-coaster can reach along the circular port...
A: Given:Radius of curvature, r=20 mmaximum acceleration, amax=2.5 g
Q: 7 8 10 15 20 25 10 15 20 3. 3 6. 8 9 8 9 2, 4. 16 5n 4. 4.
A: Hi and thank you for the questions. We are authorized to answer one question at a time, since you ha...
Q: Question 4 n punching a hole on a metal plate, the puncher exhibits shearing stress. O True F) False
A: True , puncher exhibits shearing stress, shear stress is responsible for punching out of hole.
Q: 8.7 At a point in a material under stress, there is a compressive stress of 200 MN/m and a shear str...
A:
Q: Determine the force that hydraulic piston DB exerts on boom ABC, as well as the force exerted on the...
A:
Q: Shaw thent pve= Constant For achabatic proass. an %3D
A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not im...
Q: The cylinder of a portable hydraulic riveter is 220 mm in diameter. The pressure of the fluid is 14 ...
A: From the given data, Diameter of the cylinder = d = 220 mm Gauge pressure of the fluid = P = 14 N/mm...
Q: A water pump is required to deliver 10 m2/min of water at a temperature of 27°C and the pressure is ...
A: Answer: The power required to drive the pump is 46.6757 kW.
Q: A uniform bar with an area of 0.25 in2 is pulled between two points. The tensile force at a temperat...
A:
Step by step
Solved in 2 steps with 2 images
- The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.The figure shows the FBD of a portion of the space truss shown in Fig. P5.25. Use this FBD to find the force in member BD.For the truss, which shows the reactions found at the supports at A and E, answer the following: a)Find the member forces at A and B using the method of joints. b)Find the member forces of CD, GD, and GF using the method of sections. (ps. this question is from an architectural structures class, I am struggling to begin)
- Using the method of joints, determine the force in each member of the roof truss shownin Figure -07. State whether each member is in tension or compression.Determine the force in each member of the truss and state if the members are in tension or compression (please use method of joints). For the second image please draw the free body diagrams in detail. ThanksWe want to use the method of sections for this problem to find the force in members LK, KC, and CD of the Pratt truss. Take that P1 = 20 kN , P2 = 33 kN and P3 = 39 kN B) Determine the force in the member CD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
- Solve for the reactions, the forces in each of the member and state if it is a tension or compression. Show your COMPLETE solutions and BOX your final answersFind the axial forces in members BD, DE, BC and DC of the truss by using method of joint. State whether the member undergoes tension and compresion. Show your complete solution.Determine the force in members GE, GC, and BC of the truss as shown below. Indicate whether the members are in tension or compression OPTION:(MULTI CORRECT(MAY BE)): 1.Force in Member BC is about 800 N Compressive 2.Force in Member GE is about 800 N Compression 3.Force in Member GC is about 500 N Tensile 4.Force in Member GC is about 600 N Tensile 5.Force in Member GE is about 700 N Compressive 6.Force in Member BC is about 900 N Compressive 7.Force in Member GC is about 500 N Compressive 8.Force in Member BC is about 900 N Tensile 9.Force in Member BC is about 800 N Tensile 10Force in Member GE is about 700 N Tensile 11.Force in Member GE is about 800 N Tensile 12.Force in Member GC is about 600 N Compressive
- We want to use the method of sections for this problem to find the force in members LK, KC, and CD of the Pratt truss. Take that P1 = 20 kN , P2= 33 kN and P3 = 39 kN A) Determine the force in the member KC, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.The truss carries the loads as shown in Figure 2. The truss is supported by pin at A and smoothroller support at G. (b)By using method of section, determine the force in members CD, CJ and KJ of the truss.State if the members are in tension or compression.Find the magnitude of the force members of the truss shown below, and determine if it is tension or compression. Show solution and use 4 significant figures only. Thankyou!