field measuring 45 m x 90 m is to be prepared using 1-m upland power tiller at a speed of 3 kph. Assume 10% overlap between passings and 9 seconds turn around each time at the end of each pass. Determine the actual field capacity when tilling is done along the longer field direction. Do not round off during computation, do not round your final answer, write all the decimals. Use 745.7 w/ HP and G = 9.806 M/S

field measuring 45 m x 90 m is to be prepared using 1-m upland power tiller at a speed of 3 kph. Assume 10% overlap between passings and 9 seconds turn around each time at the end of each pass. Determine the actual field capacity when tilling is done along the longer field direction. Do not round off during computation, do not round your final answer, write all the decimals. Use 745.7 w/ HP and G = 9.806 M/S

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

A field measuring 45 m X 90 m is to be prepared using a 1-m upland power tiller at a speed of 3 kph. Assume a 10% overlap between passings and 9 seconds turn around time at the end of each pass.Determine actual field capacity when tilling is done along the longer field direction:a. 0.23 ha/hr b. 0.25 ha/hrc. 0.27 ha/hr d. 0.29 ha/hr
please resolve this but make the value of P = 185 kN. Good rate will be given!
SOLVE FOR1 HR
A barge 10m wide by 30 m long when loaded the barge displaces 5 MN and its center of gravity is 0.5 m above the water line. a. Compute the righting moment for a roll angle of 10° Unit of the Correct Answer: kN-m Decimal Places required in the final answer: 4 b. Find the value of MBo. Unit of the Correct Answer: meter Decimal Places required in the final answer: 4 c. Determine the metacenter height above the center of gravity for a roll angle of 10°. Unit of the Correct Answer: meter Decimal Places required in the final answer: 3
Due in 1 hr Please show complete figure and solution thanks!! Question: A rectangular scow 9.0m wide and 15m long has a draft in fresh water 2.45m. Its center of gravity is located 4.57m above its base. If a load 500kn is place on the right hand side of the scow such that the side will just be submerge. Determine a.) Height of the scow.
Convert all units in SI. Round off to 2 significant figures. Use Francis Formula. A sharp-created weir 2ft high extends across a rectangular channel 8 ft wide conducting irrigation water. If the measured head is 4 3/4 in., determine the discharge.
You have a rectangular box 1.5m long, 0.8m wide and 0.6m high. How many gallons of water can it hold? (1.0 gal = 0.134ft^3 and 1.0m = 3.281 ft)
A tank to form a frustum of a right circular cone 1.50m in diameter at the bottom, 3m diameter at the top, 3.5m high, is full of water. A sharp edged orifice with C=.62 is located at the bottom of the tank. What diameter of orifice is needed to empty the tank in 8 minutes?
find diameter of the well to yield 4000 Iph, if c=0.09/h and depression head = 0.8m.
SOLVE FOR 1 HR. SHOW "COMPLETE AND NEAT SOLUTION" OBSERVE 3 DECIMAL PLACES
An open tank has a 3 m square horizontal section and weighs 3.5 kN. It contains water to a depth of 1.0 m. An unbalanced force of 15 kN is applied to the tank parallel to one of the pair of sides. Determine the minmimum height in meters of the tank in order to prevent any spillage. a.1.24 b.1.60 c.1.76 d.1.50
1.A rectangular canal, 6.54m wide and 1.54m deep lined with smooth stone (n=0.013) has a hydraulic slope of 0.001. Channel is laid 5m long. What savings in earth excavation (m3) Choices: 0.71 7.11 1.71 11.7 and lining (m2) were introduced using the most efficient rectangular section but adhering to the same discharge and slope? Choices: 2.99 1.99 3.99 4.99 Please we need it ASAP and please base your answer on the given choices thank you