figure below, five faces are insulated. The sixthtemperature is 30°C. Heat is uniformly generatedFor the three-dimensional object shown in theface (PQRS), which is not insulated, interactsthermally with the ambient, with a convective heattransfer coefficient of 10 W/m²K. The ambientinside the object at the rate of 100 W/m³.Assuming the face PQRS to be at uniformtemperature, its steady state temperature isFER}-2 m.S-1 m-(a) 10°C(c) 30°C(b) 20°C(d) 40°C

Given data h=10W/m2K Ta =30 oC qgen=100 W/m3

figure below, five faces are insulated. The sixth thermally with the ambient, with a convective heat For the three-dimensional object shown in the face (PQRS), which is not insulated, interacts transfer coefficient of 10 W/m²K. The ambient temperature is 30°C. Heat is uniformly generated inside the object at the rate of 100 W/m. Assuming the face PQRS to be at uniform temperature, its steady state temperature is E R} -2 m S -1 m (a) 10°C (c) 30°C (b) 20°C (d) 40°C

figure below, five faces are insulated. The sixth thermally with the ambient, with a convective heat For the three-dimensional object shown in the face (PQRS), which is not insulated, interacts transfer coefficient of 10 W/m²K. The ambient temperature is 30°C. Heat is uniformly generated inside the object at the rate of 100 W/m. Assuming the face PQRS to be at uniform temperature, its steady state temperature is E R} -2 m S -1 m (a) 10°C (c) 30°C (b) 20°C (d) 40°C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.8P

See similar textbooks

Similar questions

Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
Its thickness is 1.18 m, its thermal conductivity is 2.75 W/m.°C and its surface area is 15m2Consider a wide plane wall. Inside of the base plateThere is a uniform heat flux produced on its surface with the help of the resistance wire inside.590 W/m2 on the left surface of the wall at x=0net heat fluxand the temperature on this surface was measured as 590 °C. On the wallassuming that there is no heat generation and that the thermal conductivity is constant;a) The differential equation for continuous one-dimensional heat conduction in the wall, andSet the boundary conditions.b) Solve the differential equation to obtain a relation for the temperature change at the wall.c) Calculate the heat loss rate from the wall.
A metal cube of 0.1 m sides is being cooled down uniformly from 300°C to 30°C by placing it in cold water at 10°C. The convection coefficient of water around the cube is 40 W/m².K. The properties of the cube material are as follows - thermal conductivity: 137 W/m-K, density: 1600 kg/m³; specific heat: 800 J/kg.K. Neglect radiation. Find the time required for coo cooling. 1426-2
The roof of a house absorbs a solar radiant flux of 600 W/m?, while the underside to the ceiling is perfectly insulated (assumed). The convection coefficient between the roof and the ambient air is 30 W/m2-K. Neglecting radiation exchange with the surroundings, what is the temperature of the roof under steady state conditions if the ambient air temperature is 28°C? Express your answer in °C
Q2 FigureQ2showsaHeatingRoom,whichpartlyisolated.Thereisathermalsystemconsisting of an electric heater in a room. Heat input by the heater is Q1and heat loss from room is Q2. Air in the room is at uniform temperature, ?, and surrounding temperature is ?o. Thermal capacity of the room is C, and wall thermal resistance is R. (a) Determine a mathematical model of temperature of the room. (b) DeterminetheTransferFunctionoftheheatingroom. (c) Determine the output response of the system when a step input 25°? is given.
An electric fan has the motor inside a sphere of 25 cm diameter, which gives a uniformly distributed heat source of 2500 W/m2. A three blades of 50 cm long and 3 mm thickness and 15 cm wide are welded to the surface of the sphere. The convective heat transfer coefficient between the air and the blades is 15 W/me, and the thermal conductivity of the sphere and the blade is 8 W/m.cy and the ambient temperature is 5c. What is the temperature of the blade at 35 cm from the sphere, and the heat transferred by the three blades.