Figure below shows a bolted and doweled joint eccentrically loaded in shear. The bolts and dowel pins are used to connect the two parts. The shear loads are taken by the dowel pins, the sizes of which are: dA = 0.375 in, dB = 0.375 in, dC = 0.250 in, dD = 0.250 in, dE = 0.250 in. Dowels with diameters of zero are not present. Though the figure shows 5 dowel pins, that is not the case if some dowels are with zero diameters. Assume that a = 4 in, b = 4 in, l = 10 in, P = 2500 lb. Suppose that all of the dowels will take all the shear loading and will share the load equally. Assume that one part is allowed to rotate slightly about the centroid with respect to the other part. Part A Find the magnitude of the total shear force acting on dowel A. Express your answer in pounds to three significant figures. Part B Find the direction angle of the total shear force acting on dowel A measured counterclockwise from the positive x axis. Express your answer in degrees to three significant figures. Part C Find the magnitude of the total shear force acting on dowel E. Express your answer in pounds to three significant figures.

Q: Draw a Venturi flow meter. Make sure to show the main pipe and the U-tube manometer. Label…

A: Required: Venturi meter figure with complete details.

Q: MN m 0.5 m Each ball has a negligible size and their respective mass are 9-kg and 3-kg. Each ball is…

A: Given: mA=9  kg mB=3  kg r=0.5m M=t2+2 V(t=0s)=9m/s   To find: V(t=6s)

Q: Draw the Temperature & compute the LMTD for CO-CURRENT & COUNTER-CURRENT flow heat exchanger. Steam…

A: Given:Initial temperature of water, Twi=70°CFinal pressure and state of water, Pwf=800kPa and…

Q: Is it possible for an item to fail yield but not fail fatek

A: Given question : Is it possible for an item to fail by yielding but not fail by fatigue.   .

Q: Larger animals have sturdier bones that smaller animals. A mouse’s skeleton is only a few percent of…

A: Given data:   Mass of man = 70 kg Cross-sectional area of femur = 4.8 x 10-4 m2 Compressive strength…

Q: (a) Determine the reactions at A and E if P = 840 N. The reactions are positive if to the right or…

A:

Q: An 8.70-kg block slides with an initial speed of 1.56 m/s up a ramp inclined at an angle of 28.4°…

A: Given data as per the question Mass of block =8.70 kg Initial velocity =1.56 m/s inclination angle…

Q: Describe the two alignment steps that need to be performed when setting up the rotary table on the…

A:

Q: A 1/2-in-dia UNC, class 2 bolt with rolled threads is preloaded to 80% of its proof strength when…

A: Part (A): Write the given data. d=0.5 inL=3 inPmax=1000 lb

Q: Find Σ MD

A:

Q: SAE 30 oil at 60 F is pumped through a 6-ft diameter pipeline at a rate of 6650 gal/min. A model of…

A:

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A:

Q: 1. Ch. 8 An 8-m-long, uninsulated square duct of cross section 0.2 m x 0.2 m and relative roughness…

A:

Q: (2/149) A jet plane flying at a constant speed at an alti- tude h = 10 km is being tracked by radar…

A:

Q: A 1 m3 container is filled with 0.30 m3 of granite, 0.12m3 of sand, 0.20m3 of water at 25 0C the…

A: GivenV=1m3Vg=0.30 m3Vs=0.12m3Vw=0.20 m3Vair=0.38 m3ρair=1.15 kg/m3ρg=2750 kg/m3ρs=1500 kg/m3ρw=997…

Q: The 213-kg wheel has a radius of gyration about its center O of ko = 240 mm, and radius r = 0.4 m.…

A:

Q: 4.2. The ball catathermometer factor (F) is 620, time while the spirit column drops from 38 to 35°C…

A: Given   Catathermometer factor, F = 620 Temperature, T1 = 38oC                        T2 = 35oC Air…

Q: decimal point, and proper unit. Take g = 9.81 m/s². R @ 5 3 P

A: Given system,

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: The volumetric analysis of a mixture of gases is 30 percent oxygen, 40 percent nitrogen, 10 percent…

A:

Q: Gear A is held fixed, and arm DE rotates clockwise with an angular velocity of WDE = 6 rad/s and an…

A:

Q: Q/A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span…

A: Given data Transmit power =7.5 kw Rotating speef =300 rpm Shear stress=45 mpa Pressure angle =20° We…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Make a graph illustrating Eutectic Systems and expalin.

A: Introduction A homogenous, solid combination of two or more materials that forms a super-lattice is…

Q: Determine the tension T on the cable if the boom has a weight of 500N. b)Determine the force…

A:

Q: B. What is the pressure of the liquid at the top of the pipe? Assume that the system is exposed to…

A: Given data The radius of the cylinderical pipe is:r=1.30 cm The length of the water drum is:l=2.20…

Q: An isolated cylinder-water device contains 5 l of saturated liquid water at a pressure 200 kPa…

A:

Q: Using general equation of incident angle, derive the formula for a north facing-tilted surface in…

A: Introduction: The angle of incidence is the angle formed by a ray of light with the normal drawn at…

Q: In detail what are water fog systems

A: Water fog is the process in which water is made in the form of fine spray of water droplets. This…

Q: 4. A sine wave has a frequency of 50 kHz. How many cycles does it complete in 10 ms?

A:

Q: Consider an opaque, diffuse surface whose spectral reflectivity varies with wavelength as shown. The…

A:

Q: 1. A block of copper at a temperature of 50 °C is placed in contact with a block of aluminum at a…

A: As per Bartleby code of conduct, it is recommended to answer the first three questions of the…

Q: -powered subma 7-39 A student rine for a design competition. The overall length of the proto- type…

A: Given   Length of prototype, LP = 2.24 m Velocity of prototype, vp = 0.52 m/s Find    Velocity of…

Q: 7. Find the power to pull a a 50kg upward a constant velocity of 13m/s,

A:

Q: Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a…

A:

Q: A beam held by a hinge, take 2. The left end of a beam of mass 17.9 kg and length L is fixed to a…

A:

Q: d. none UI In an air-standard Diesel cycle, the compression ratio is 16, the cylinder bore is 200mm…

A:

Q: Problem 4: The state of plane stress shown occurs in a machine component made of a steel with…

A: Given,

Q: Wall Shear Stress and Pressure: The average blood velocity through an internal carotid artery with a…

A: Given data: D=5 mm u=15 cm/s μ=3.5 cp

Q: Figure Q1 (b) 6.9 07.0 Figure Q1 (a) 10.0

A: Given: a) sketch the dimensions of  figure Q1. b) Front view referring to figure Q1.

Q: Propane at 350 °C and 600 cm³/mol is expanded in an isentropic turbine. The exhaust pressure is 1…

A: Given data: Initial conditions : T1 = 350°C = 350 + 273 K = 623 K v1 = 600 cm3/mol    After…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Which term(s) in this equation is/are eliminated if Point A is stationary? Which term(s) in this…

A: Given: To find: Terms eliminated if A is stationary Terms eliminated if A rotates with constant…

Q: Given • 1 million people in Hong Kong using low-flush toilet and low- flow shower head. • 1 million…

A: Rate of CO2 production= 1.83 kg/kg of coal To find: 3. How much CO2 we can reduce?

Q: 6. x9(x) = qo sin- L Find M(x), V(x) using π.χ. d²M dx² = q(x) j

A: In this problem, it is asking about question (6) only so we will provide the solution for question…

Q: The maximum stress a material can with stand before failing is termed.... O O the elastic limit the…

A: The maximum stress a material can with stand before failing is termed... Answer: the ultimate…

Q: Calculate the Coefficient of Performance for an ideal vapor-compression air conditioner operating…

A: Given data:- ideal vapor-compression air conditioner Evaporator temperature =10°C =283K condenser…

Q: The aluminum fuel tank (α = 23.8 x 10-6 m/moC) on a sailboat measures 40 cm by 50 cm by 75 cm. If it…

A: To find: The fuel leak from the tank due to increase in temperature. Given: The thermal expansion…

Q: Given • 1 million people in Hong Kong using low-flush toilet and low- flow shower head. • 1 million…

A: Given data: Coal consumption m˙coal=0.45 kg/kWh Find: 2. How much coal (Kg) we can save?

Q: 3) Find the forces developed in beams FE, CE, and CD. State whether they're in tension or…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.