Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the following values on the table would be observed on the system, determine the value of normal stress in MPA, round off your answers to nearest whole number. Ørod 6.5 mm 2250 N a 125 mm b 200 mm 165 mm (1) d 85 mm 60

Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the following values on the table would be observed on the system, determine the value of normal stress in MPA, round off your answers to nearest whole number. Ørod 6.5 mm 2250 N a 125 mm b 200 mm 165 mm (1) d 85 mm 60

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 43P: A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the...

See similar textbooks

Similar questions

SOM 3.1 Show your complete/correct solution. ( I need detailed solution since there is given answer.) Given answer: Stress in bars AC = 49468.962 psi Stress in bars CB = 8588.361 psi
The figure shows a homogeneous. rigid block weighing W = 14 kips that is supported by three symmetrically placed rods. The lower ends of the rods were at the same level before the block was attached. Determine the stress (psi) in the steel rod after the block is attached and the temperature of all bars increases by 106 °F. Use the following data: Rod Area (in2) E (psi) α (/°F) Length (ft.) Each steel rod 0.98 29 x 106 6.7 x 10-6 3 Bronze rod 1.79 12.6 x 106 10.9 x 10-6 9
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
SOM 1. Show your complete solution. ( I know the answers but I need the detailed solution) Given answers: Stress in bar AC = 49468.762 psi Stress in bar CB = 8588.361 psi
The figure shows a sign hanging from a beam anchored to a wall by two cables. In an element of the beam, the stress tensor has been measured, resulting in the following values σxx = 2250 [psi], σyy = 1175 [psi] and τxy=−820 [psi]. Q) It is known that σyield= 2000 [psi]. Is it possible that the beam could fail? Apply the Von Mises and Tresca criteria
A copper cylinder with a length of 1.5 m and diameter of 4 cm undergoes compression. (refer to Table 4.1) (a) What will be the bulk strain of the copper rod if pressure is applied to reduce its volume to 0.00089 m3? (b) How much pressure was applied to the copper rod? (c) Calculate the percent change in volume of the copper rod.
Shear force and bending moment values for cross-section are given in Table 1. Split the values (noting the sign) over their parts. Using these values, calculate the bending stress and shear stress values and draw the stress diagrams next to the section. Note: Draw the Bending (Normal Stress) diagram and Shear stress diagrams separately and show them on all the values you find. In this question, study unit changes in kg and cm. T (ton)80 M(tm)-30 b (mm)50 h (mm)750 t (mm)55
A thin sheet of rubber in the form of a square is uniformly deformed into the parallelogram shape as shown in the figure. All edges remain the same length ?, as the sheet deforms. Determine the average normal strain along the diagonal ??. Length ? is in millimeter (mm). Answer in 4 decimal places
Assume σx=109 MPa, σy=140 MPa, and τx⁢y=58 MPa for the given figure below. Determine the minimum normal (principal) stress (in MPa). Express final answer in 5 significant figures.
Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER Using MOHR CIRCLE, what is the resulting "VERTICAL" NORMAL STRESS at the given angle plane point? a. 44.03 MPa b. 75.00 MPa c. 64.32 MPa d. 185.68 MPa
Two masses are attached to a uniform meter stick as shown in the figure below. Themasses of m1 and m2 are as given and the meter stick weighs 150 g. A force F withunknown magnitude is applied on one end of the stick at an angle of 30° to balancethe system. (a) What is the magnitude of F? (Ans: 6.21 N)(b) What are the reaction forces on the support? (Ans: Rx = 5.38 N; Ry = 5.80 N)