Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625in., calculate the power coefficient (Cp*) of the given pump at BEP if water is the fluid.HEAD IN FEET0000504020108.625"30 (219mm).0O 0.821O 0.731O 0.467aco10O 0.235L/SEC 59.25"(235mm)8.00"(203mm)7.375"(187mm)6.75"(171mm)125Model 5009FI & CI Series2515 20-doCURVES BASED ON CLEAR WATERWITH SPECIFIC GRAVITY OF 1.072%75%3079%1160 RPMFEBRUARY 19. 2002403,545REQUIRED NPSH1.5HP(1.1KW)79%1⁰⁰of15²Curve no. 2140Min. Imp. Dia. 6.75"Size 6 x 5 x 9.0505560250 375 500625FLOW IN GALLONS PER MINUTE72%2HP(1.5KW)colo&2⁰.It & SC-09.55%5%3HP(2.2KW)7.5HP(5.6KW)45%de750 875NGFEET1512-9-63010850SHP(3.7KW)NPSHHEAD IN METERS1000r4536F2718-90-100--804 -40-602 -20-OHEAD IN KILOPASCALS

Answered: Image /qna-images/answer/2fed3ee9-1601-41f4-bb10-5a0dc05c0357.jpg

Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625 in., calculate the power coefficient (Cp") of the given pump at BEP if water is the fluid.

Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625 in., calculate the power coefficient (Cp") of the given pump at BEP if water is the fluid.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider a brake testing bench as shown in the figure. Motor 16.1 50 20 Clutch + X A motor speeds up…

Q: A. The open-loop transfer function of a unit negative feedback control system is as K GK (s) =…

A: Given:To find:(1) Evaluate the value range of K when the closed-loop system is stable.(2) Calculate…

Q: lokN 130⁰ +3m +-3m → F MIT D A B | 3m → -3m-*e3m²l **→→!

Q: A natural-draft cooling tower is to remove 70 MW of waste heat from the cooling water that enters…

A: The heat removed is The inlet temperature of water is The exit temperature of water is The dry bulb…

Q: 9-102. The elevated water storage tank has a conical top and hemispherical bottom and is fabricated…

Q: Find the x- and y-coordinates of the centroid for the composite area shown in the figure (all…

Q: Calculate the heat transfer between two (50*40 cm) parallel plates at constant temperatures of 71 =…

Q: A disk with radius R and mass m begins from rest and then moves without slipping while being pulled…

A: In the above diagram, N is normal force, m is mass, g is gravitational acceleration, P is applied…

Q: The state of stress at a point in a member is shown on the rectangular stress element where the…

A: The state of stress at a point in a member is shown on the rectangular stress element where the…

Q: The rear window of a car is defrosted by the passage of warm air on the internal surface. If the…

Q: Please show your complete solution. Thank you! A 1.5 kg of an ideal gas undergoes a process wherein…

A: The mass of ideal gas is .The initial pressure is .The initial volume is .The final pressure is The…

Q: In the rigid rotor and elastic rotor models, comment on the differences between the expressions…

A: To Find:The differences between the expressions correspond to the frequencies of the first 5…

Q: The figure shows a cam and follower. Using graphical methods, find and sketch the equivalent fourbar…

Q: 12-31. The shaft is made of steel and has a diameter of 15 mm. Determine its maximum deflection. The…

A: The shaft is made of steel and has a diameter of d= 15 mm. Determine its maximum deflection.The…

Q: Please explain and show examples of chemical vapour deposition

A: Chemical Vapor Deposition (CVD) is a process used to produce thin films, coatings, or other…

Q: 13.13 Tungsten is being used at half its melting point (Tm ≈ 3,400 °C) and a stress level of 160…

A: Stress=1.6 MpaStrain rate =(10-10)s-1Final length=10.072cm

Q: For the given loads, determine the reactions at the supports of the beam.

A: The FBD of the given force systemDetermine the support reaction at A and B.

Q: Calculate the first natural frequency (m = n = 1) in Hz for a square plate with edge length a = b =…

A: To Find:The natural frequency.Given:The length of the square plate is the thickness of the square…

Q: In a three-stage compression system, air enters the first stage at a pressure of 100 kPa and a…

A: Given-

Q: 1m RM 600 kN/m 3m PILES RT 1m Slab A Slab B shear connector B 200 mm A 600 mm 400 mm 200 mm The…

Q: D-Q-1 Write T for true Statement or F for False Statement. [1]. Heat transfer: is transit mass…

A: Disclaimer:Hello. Since you have submitted multiple questions, we will solve the first one for you.…

Q: Prob. # 4] The torsional deformation of a steel shaft is 1° in a length of 2 ft when the shearing…

A: The torsional deformation of the shaft, ()=1oThe length of the shaft, (L)=2 ftThe shearing stress in…

Q: An adiabatic pump is used to compress saturated liquid water at 10 kPa to a pressure to 15 MPa in a…

A: To Find : The work input per unit mass Given : The inlet pressure is The exit pressure is Assumption…

Q: 3. Find the acceleration of C and the angular accelerations of links 3 and 4. r1= 75-mm, r2 =…

A: Find the acceleration of C and the angular accelerations of links 3 and 4.r1 = 75 - mm r2 = 150 - mm…

Q: Problem 1: Recall the two-mass system from a previous problem set, in which you deter- mined the…

A: To Find:the function of the potential energy.the Taylor expansion series.The total kinetic energy…

Q: B. Determine the force developed in members FE, EB, and BC of the truss and state if these members…

A: Determine the force developed in members FE, EB, and BC of the truss and state if these members are…

Q: The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A…

A: To Find:The normal stress in the direction of the x′-axis.The shear stress in the y′-direction for…

Q: 8.20 Water is the working fluid in an ideal Rankine cycle with reheat. Superheated vapor enters the…

Q: An Al2O3 specimen is being pulled in tension. The specimen contains flaws having a size of 100 µm.…

Q: Calculate the stiffness matrix for the Q8 element shown below. Make use of the shape functions in…

Q: The four bar linkage in Fig. 2 is driven by link 2 at constant angular velocity of 300rpm ccw.…

Q: 14-115 The condensation of the water vapor in compressed- air lines is a major concern in industrial…

A: To find:The condensation in the compressed-air lines on a day when the ambient air is at 20°C and 50…

Q: A reversed cycle operating as a heat pump uses R-134A as the working fluid. It is designed to…

Q: Two members of uniform cross section 65 x 95 mm are glued together along Plane a-a that forms an…

Q: Given the isometric drawing of the solid, draw the multiview projection.

A: Given:

Q: If a student were performing this experiment at an ambient temperature and pressure of 70°F and 1…

A: Given- temperature= 70 degree F pressure= 1 atm velocity = 15.5…

Q: 6. Write one block of code to perform the indicated operation. Assume the location s X2.0, Y2.0, and…

Q: (a) What is the proeutectoid phase? (b) How many kilograms each of total ferrite and cementite form?…

Q: A 60,000 ft2 building used 850,000 kWh of electricity and 900 Mcf of natural gas over the past 12…

A: Given:The area of the building is the energy consumed by the building due to electricity for one…

Q: 2. Why a pulsed mode generator with a very small duty cycle is needed in the forward voltage…

A: A device that produces regulated, intermitten signals at particular nodes within a system or circuit…

Q: A piston, mp= 5 kg, is fitted in a cylinder, A = 15 cm2, that contains a gas. The setup is in a…

Q: Mechanics question 1: Figure 1.1 shows a rod, AB, 1 m long, and with weight W, which is held in…

A: Given data:The length of the rod is, The rod is held in equilibrium by a vertical wall, the…

Q: Write the mathematical expression for the internal shear in segment CD in terms of x with point A as…

A: For the solution refer below images.

Q: A 5kg collar is suspended by a spring at rest a Point A, as shown. The unstretched lenght of the…

A: The collar is rest at point A.The unstrecthed lengthof collar is The mass of collar is The collar is…

Q: The system is used to lift a block with mass 300 kg. If the friction coefficient between two blocks,…

A: To Find:The minimum force required is such that the object is about to be lifted.Given:the mass of…

Q: Problem 3: The figure below shows a manometer being used to indicate the pressure difference between…

A: Given,A venturimeter which is connected with manometer to measure pressure difference.Diameter D1 =…

Q: The conduit in the figure has a diameter of 3 cm and is made of cast iron (ε= 0.26 mm). The fluid…

Q: Inlet enthalpy at the given pressure P1 = 800 kPa and temperature T1 = 35°C is; h1 = 271.24 kJ/kg…

A: Here you are asking for the table which is used in this question.

Q: A1. Produce a Mohr's circle for the stress state of a 2D plane stress element at position C (located…

Q: An auditorium seating 1800 people in three consecutive sitting for 6 hours, is to be maintained at…

A: An auditorium seating 1800 people in three consecutive sitting for 6 hours, is to be maintained at…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625
in., calculate the power coefficient (Cp*) of the given pump at BEP if water is the fluid.
HEAD IN FEET
0000
50
40
20
10
8.625"
30 (219mm).
0
O 0.821
O 0.731
O 0.467
aco
10
O 0.235
L/SEC 5
9.25"
(235mm)
8.00"
(203mm)
7.375"
(187mm)
6.75"
(171mm)
125
Model 5009
FI & CI Series
25
15 20
-do
CURVES BASED ON CLEAR WATER
WITH SPECIFIC GRAVITY OF 1.0
72%
75%
30
79%
1160 RPM
FEBRUARY 19. 2002
40
3,5
45
REQUIRED NPSH
1.5HP
(1.1KW)
79%
1⁰⁰
of
15²
Curve no. 2140
Min. Imp. Dia. 6.75"
Size 6 x 5 x 9.0
50
55
60
250 375 500
625
FLOW IN GALLONS PER MINUTE
72%
2HP(1.5KW)
colo
&
2⁰.
It & SC-
09.
55%
5%
3HP
(2.2KW)
7.5HP(5.6KW)
45%
de
750 875
NGFEET
15
12
-9
-6
3
0
10
8
50
SHP(3.7KW)
NPSH
HEAD IN METERS
1000
r45
36
F27
18
-9
0
-100
--80
4 -40
-60
2 -20
-O
HEAD IN KILOPASCALS

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation of power coefficient

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A centrifugal pump operating at 1150 rpm showed a total head of 40 ft. at a capacity of 600 gpm. The impeller diameter is 10.5 in. Estimate the total head and capacity of a geometrically similar pump at 1150 rpm with an impeller diameter of 10 inches.
A radial flow pump operating at maximum efficiency at a specific speed of 2300 is to deliver 260gpm against a head of 129ft at a rotative speed of 2100 rpm. Find the required number of stages. ANSWER: 3
A six-centrifugal pumps delivers 0.1 m^3/s against a total head of 480 m. What is its specific speed if it routes at 1450 rpm? What type of impeller would you recommended for the pump? Draw velocity triangles for centrifugal pump at inlet and outlet. Drive expressions for power input, power output and efficiency for Francis turbine using flow velocity triangles.
A centrifugal pump was designed for a 1940 rpm operation and a head of 63.4 m has a capacity of 201.2 l/s (lps) with a power of 135. kW. What effect will a speed reduction to 1200 rpm have on the head, capacity and power input of the pimp? What will be the changes in these variables if the impeller diameter is reduced from 332.5 mm to 275 mm while the speed is constant at 1800 rpm? Required a. For D = c, find Q2, H2 and P2 b. For N = c, find Q2, H2 and P2
A centrifugal pump has a 41.5-in-diameter impeller. It is used to deliver water at about 12,000 gal/min. Its pump performance curve when spun at 710 RPM is shown in the figure below. If the impeller is trimmed to a new diameter of 39.5in, estimate the new head (in feet) and flow (in gal/min or GPM) if the speed is not changed.
Shown in the Figure is the complete pump performance chart for a 3×4-10 centrifugal pump at 1750 rpm. The centrifugal pump must deliver at least 200 gal/min of water at the total head of 50 ft. (3) What is the power required for the selected impeller? _________ A. 5 hp B. 4.2 hp C. 2.2 hp D. 3.2 hp
A 2-stage centrifugal pump delivers 50 gpm of 225ºF water against 200 ft head at 3200 rpm. a) What is its specific speed? b) What head could a geometrically similar pump produce if operated at 45 gpm flow?
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1.Question : A centrifugal pump has impeller with dimensions r1 = 71 mm, r2 = 154 mm, b1 = 52 mm, b2 = 26 mm, β1 = β2 = 30º. For discharge of 74 L/s and shockless entry to vanes, compute the speed in rpm.Answer : 743.12 rpm
A gear pump has a 80-mm outside diameter, a 55-mm inside diameter, and a 25-mm width. If the actual pump flow rate at 2300 rpm and rated pressure is 140 LPM, calculate the Theoretical Flow Rate, QT (m3/s). (Hint: first calculate the Displacement Volume) Group of answer choices 0.00361 m3/s 0.00233 m3/s 0.00254 m3/s 0.00262 m3/s
A manufacturer of small water pumps lists the performance data for a family of its pumps as a parabolic curve fit, Havailable = H0 − aV.2 , where H0 is the pump’s shutoff head and a is a coefficient. Both H0 and a are listed in a table for the pump family, along with the pump’s free delivery. The pump head is given in units of feet of water column, and capacity is given in units of gallons per minute. (a) What are the units of coefficient a? (b) Generate an expression for the pump’s ree delivery V.max in terms of H0 and a. (c) Suppose one of the manufacturer’s pumps is used to pump water from one large reservoir to another at a igher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure. The system curve simplifies to Hrequired = (z2 − z1) + bV.2 Calculate the operating point of the pump (V. operating and Hoperating) in terms of H0, a, b, and elevation difference z2 − z1.
Using affinity laws, develop a pump curve and BHP curve for a 1 ½" AB pump for a 6" impeller. Use a 1750 rpm curve as the "known" characteristics and develop a theoretical curve using affinity laws for 3500 rpm based upon flow rates 0, 20, 40, 60, 80 and 90 gpm at 1750 rpm. Plot the theoretical (affinity-based) and published flow vs. head and flow vs. horsepower curves for 3500 rpm.
A gear pump has a 80-mm outside diameter, a 55-mm inside diameter, and a 25-mm width. If the actual pump flow rate at 2300 rpm and rated pressure is 140 LPM, calculate the Displacement Volume, VD (m3) Group of answer choices 66.9x 10-7 m3 56.3 x 10-6 m3 66.3 x 10-6 m3 97.1 x 10-7 m3 70.9 x 10-6 m3