Figure Q16 shows a simple bolted single lap joint plate and a simple bolted double lap joint plates under a load of P (N). Each bolt lap joint uses the same bolt with a diameter of d (mm). Which option correctly shows the shear stress (T) equations for the bolt in the single and double lap joint plates? Simple Bolted Single Lap Joint P Simple Bolted Double Lap Joint P/2 P/2 d

Figure Q16 shows a simple bolted single lap joint plate and a simple bolted double lap joint plates under a load of P (N). Each bolt lap joint uses the same bolt with a diameter of d (mm). Which option correctly shows the shear stress (T) equations for the bolt in the single and double lap joint plates? Simple Bolted Single Lap Joint P Simple Bolted Double Lap Joint P/2 P/2 d

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.6P

See similar textbooks

Similar questions

The 13-mm thick plates of the lap joint shown is made of A36 steel whose yield strength and tensile strength is 248 MPa and 400 MPa, respectively. The bolts are A325-M22. The holes are standard sizes and the threads are excluded from the shear plane. Assume that deformation at bolt holes is a design consideration. Determine the design (LRFD) strength of the lap joint based on shear strength (kN) of the bolts. [Group of Answers: 424, 521, 390, 318] Determine the nominal strength of the lap joint based on shear strength (kN) of the bolts [Group of Answers: 424, 566, 521, 695]
A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm in diameter. Compute the number of additional 10 mm - diameter bolts on a bolt circle 200 mm in diameter to increase the torque capacity to 7.65 kNm. The shearing stress of the bolts should not exceed 60 MPa. Select one: O a. 6 bolts O b. 4 bolts O c. 3 bolts O d. 2 bolts NEXT PAGE
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 60mm 50mm) 8mm P
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.
Determine the allowable tensile force P which can be appllied to the plates shown. The AISC specifications A36 steel and 20 mm diameter A325 bolts placed in standard holes with threads excluded from the shear plane are used in a bearing in a bearing type connection. Fy = 248 MPa, Fu = 400 MPa, Fv = 206.9 MPa and Fp = 1.5 Fu. P P CIVIZ 12mm 250 mm ENGINEERING - STEEL DESIGN 12mm P P
A plate 400x12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is requireed to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use LRFD. Fnv = 300 MPa Fu = 400 MPa Fy = 248 MPa Ag = 3354 mm2 Question: Determine the capacity of the channel based on the bearing strength of the connection.
4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
2-PL10x1/2 A-36 Bolts are 7/8 in A-325, threads are not excluded. All edge spacings are minimum | 3" | 3" | о PL 10x3/4 A-572Gr50 a) Determine the nominal bolt capacity. b) Determine the nominal bearing capacity for each plate. c) Determine the nominal rupture capacity of each plate. d) What is the nominal capacity of the connection? e) Using LRFD, is this connection capable of supporting a dead load of 150 kip and a live load of 100 kip?