Figure Q1(b) shows three rods that were assembled together and held between rigid supports. The material properties of each material are given in Table Q1(b). Suppose the initial temperature is T1 = 2x °C. The temperature then raised up and reaches T2 = 7y °C. Parameter x and y are given by: x = last digit of your matrix number y = fifth digit of your matrix number For example, a student with the matrix number CD200187 will have the values of 2x = 27 and 7y = 78. i. Calculate the average normal stress in each material when the temperature reaches T2. ii. Determine the corresponding displacement at point A.

Figure Q1(b) shows three rods that were assembled together and held between rigid supports. The material properties of each material are given in Table Q1(b). Suppose the initial temperature is T1 = 2x °C. The temperature then raised up and reaches T2 = 7y °C. Parameter x and y are given by: x = last digit of your matrix number y = fifth digit of your matrix number For example, a student with the matrix number CD200187 will have the values of 2x = 27 and 7y = 78. i. Calculate the average normal stress in each material when the temperature reaches T2. ii. Determine the corresponding displacement at point A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are working with an imagined cubical pot of water, 1 meter on each side, sitting on a stove. Heat is applied to the bottom of the pot from the stovetop. The pot has been on the stove for a while, so the stovetop is hot and some heat has already been added to the water. Assume the water at the bottom of the pot is held at 99 degrees C , while the water at the top of the pot is cold, 4 degrees C. Compute the heat delivered by that 1 g of water at 99 °C into the layer of water at the top of the pot, assuming the latter is 1 meter square, 1 cm deep, and 4 °C. Start by solving the calorimetry problem (Section 14-4 in the text) to determine the final temperature of the top layer plus hot 1 gram from below. Then use that to determine how much heat was delivered in the hot water
(Solid Mechanics) This finite element model is composed of 4 linear bar elements, each with a cross section of 10 mm² and material properties (E = 6 GPa, v=0.3). A weight of 200 N is applied and the nodes are named as shown below. (1) Compute the reaction forces. (2) What are the reaction forces when the weight is tripled to be 600 N? Find the solution without repeating the FEA. Explain why you can get the quick answer.
Solve the following problems and sketch the schematic diagram describing the system. Show pertinent and complete solutions. A certain ideal gas X has molecular weight of 10 g/mol and specific heat ratio of 2. Initially, X has pressure of 200kPa and volume of 2m3. The pressure was doubled during heat transfer. Find the heat transfer if it underwent a process described by; a. n=infinity b. n=Cp/Cv c. n=3
differential equation A metal bar is placed in a room at constant temperature of 0°C. If after 25 mins the temperature of bar drops from 120°C to 55°C, find how many minutes the metal bar will continue to cool from 55°C to 50°C.
a) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by MB ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as (Hint : to input equation R2LQ2wh , you can type (R^2*L)/(Q^2*w*h) ) b) Using the provided data: cross-section width w = 20 mm, cross-section hight h = 93 mm, length of the beam L =3 m , beam material’s Young’s modulus Q =226 GPa, applied bending moment MB = 11 kN.m The value of the deflection at Point B caused by MB ( Part I) can be calculated as ......(in mm)
Given: Mass = M, Radius = R, Moment of Inertia = I, Distance = H, Gravity = g, Initial timing = 0 Unknown = How long will the [delta t] process take? (time) Please keep in mind that almost every variable is unknown! We are given no numbers and are instructed to generate a solution using the variables [ "R, M, g, I and H." ] Target = Find an equation that, if we could substitute numbers, would determine how long the process would take. Newton's second law and torque seem to be relevant based on how the problem is written. * Also please show drawing based on what we are calculating
A diver 50 m deep in 8°C fresh water exhales a 1.2 cm diameter bubble which rises to the surface of the water and has a diameter of 2.2 cm when it reaches the surface of the water. Assume the air bubble rises slow enough that it is always in thermal equilibrium with the surrounding water. Include units in all your numerical responses 1. Determine the pressure of the air inside the bubbles
Archimedes established his principle while investigating a suspected fraud in the construction of a crown. The crown was made from an alloy of gold and silver instead of pure gold. Assume that the volume of the alloy was the combined volumes of components (the density of gold is 19.3g⁄(cm^3 ), the density of silver is 10.5g⁄(cm^3 )). If the crown had a weight of 9.81 N in air and 9.10 N in pure water, what percentage of gold (by weight) was it?
Derive the stiffness matrix for a spring.
Consider an experimental structure required to always have constant pressure. For this purpose, a collapsible compartment has been installed that expands and contracts to adjust the volume of air inside the structure for maintaining constant air pressure of 1 atm. Given the total volume of air inside the structure was 100,000 m' when the compartment was fully collapsed, solve the following: If a constant pressure is to be maintained while the temperature varies from 0°F to 150°F, find the volume of air that the compartment holds when it expands to the maximum. For the temperature transition mentioned above, find the change in internal energy undergone by the air in the structure. Also, find the work done by the compartment while it expands. Assume air to be an ideal gas.
: You are abducted by aliens and find yourself locked in a large room on some strangeplanet. To pass the time, you decide to do some experiments using a ball-and-chain thatyou find on the floor. You make the following estimates:mBALL  7 kg ,mCHAIN  0.5 kg, and CHAIN  2 m .(a) When you hold the free end of the chain above your head and allow the ball to swinglike a pendulum, you use your wristwatch to measure the period asT  4 s. What is theacceleration due to gravity on this planet?(b) If the ball accidentally hits a wall, how long does it take for this jolt in the chain totravel up to your hand?
Referring to Figure 10.11, suppose you have some lizards thatare at 16°C and have been living at that temperature for 5 weeks.What is their resting metabolic rate? If the lizards are suddenlyshifted to a room at 33°C, trace on the graph how their metabolicrate will change from the moment they are placed in the newroom until 5 weeks have passed. According to the graph, willthey exhibit compensation?