Figure shows a pipe system. At the entrance to the pipe (point 1), the diameter is d₁ and it is a height h₁ from the ground. The water then exits the pipe to the atmosphere at point 2, where the diameter is d2 and the height is h2. The pressure sensor reveals that the pressure at point 1 is p₁ = p. Find an expression for the flowrate in the pipe h₁ d₁ d₂ h₂

Figure shows a pipe system. At the entrance to the pipe (point 1), the diameter is d₁ and it is a height h₁ from the ground. The water then exits the pipe to the atmosphere at point 2, where the diameter is d2 and the height is h2. The pressure sensor reveals that the pressure at point 1 is p₁ = p. Find an expression for the flowrate in the pipe h₁ d₁ d₂ h₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
The liquid being lifted by the pump below is gasoline with specific weight γgasoline = 47 lb/ft3 and a vapor pressure of 9 psi (absolute). The local atmospheric pressure is patm = 12.5 psi (absolute). The friction head loss through the pipe from its entrance to the pump entrance at B is hf = V 2 /(2g) empirically, where the velocity in the pipe is V = 7 ft/s. What is the maximum allowed value of z without cavitation occurring at the pump entrance at B?
For the system of pipes shown, the flow of water in pipe (3) is 25 L/s. Find: The flow in pipes (1) and (2): Q1 =……………….., Q2 =…………………. The difference in head between the two tanks is H =………………… f1:0.016 f2:0.028 f3:0.018
A certain amount of water (H2O) flows permanently into the pipe venturi(image2) in the figure next to it. In the stretch considered between (1) and (2), it is assumed the losses by friction that were despicable and the uniform properties in the sections are assumed. The entrance area is A1 while that of throat is A2 (A1 > A2). A pressure gauge whose manometric fluid is Mercury Hg (YHg> YH2O) is connected between the input sections and the throat. Show, without omitting any calculation steps that the flow rate at the input (1) is given by(image1):
The diameter of a pipe changes gradually from 150mm at a point A, which is 6m above datum, to 75mm in diameter at point B, which is 3m above datum. The pressure at A is 103kPa and the velocity of flow is 3.6 m/s. The fluid flowing in the pipe is water. Neglecting losses, determine the pressure at B.
When gage A indicates a pressure of 100 kPa gage, then cavitation just starts to occur in the venturi meter. If D = 40 cm and d = 10 cm, what is the water discharge in the system for this condition of incipient cavitation? The atmospheric pressure is 100 kPa gage, and the water temperature is 21°C. Neglect gravitational effects.
Water at 10°C is flowing from point A to point B through the fabricated section shown below at the rate of 0.37 m3/s. If the pressure at A is 66.2 kPa, calculate the pressure at B. answer should be 34.9 kPa
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.