Figure shows a rectangular beam section 10 cm wide and 20 cm deep. If the maximum flexural stress is 80 kg/cm2. What will be total force on area shaded and moment of this force about the neutral axis respectively. 5 cm N- A -10 cm 10 cm 10 cm 5 cm

Figure shows a rectangular beam section 10 cm wide and 20 cm deep. If the maximum flexural stress is 80 kg/cm2. What will be total force on area shaded and moment of this force about the neutral axis respectively. 5 cm N- A -10 cm 10 cm 10 cm 5 cm

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Related questions

Q: Evaluate J (sin t + 1)-1 dt. S(sin t A sin t - sec t + C B tan t - csc t + C tan t + sec t + C D) ta...

A: To evaluate the given integral. Given, I=∫sin t+1-1 dt The given integral can be evaluated by si...

Q: Find the minors of every element of the following matrices: For part (a): 1 3 -2] A = 4 -3 4 -1.

A: To calculate the minors of every element of the given matrix. Given, A= 1 3 -2 0 5 4...

Q: D. Determine the adequacy of the tension members of the determinate bolted truss shown below based o...

A: A truss is a structure composed of slender members jointed together at end points by bolting /riveti...

Q: 14. CONVERTING BEARINGS TO AZIMUTHS. Convert the following beàrings to azimuths (reckoned from south...

A: Appreciate if there is detailed work with explanation for ease of understanding. THANK YOU !

Q: Empirical models include description of hydrological processes based on cause-effect relationships t...

A: Ans: False Empirical model are observation oriented models which take information from the existing ...

Q: Whiteware, porcelain, bricks and bio-ceramics are an example application derived from ceramic materi...

A: Whiteware, porcelain, bricks and bio-ceramics are an example application derived from ceramic materi...

Q: For a drainage basin of 600 km2, isohyetals drawn For a storm gave the following data:

A: According to given data drainage basin of area 600 km2, Isohyetals drawn for a storm gave the follo...

Q: Given: A steel rod (A= 150 mm²) is stretched between two fixed points with a tensile load of 5000 N ...

Q: P.-P. (1+1)" WD. - P.x Cxt+ WD P-0.SCApu A 60 MLD water treatment plant has 4 mechanical flocculator...

Q: A CPC is a type of offset printing pr

A: Printing is the process of reproducing images from an electronic device on paper or another tangible...

Q: A gas at 45 degrees Celsius is under pressure of 398.675 kPa. Assume gas constant of 287N-m/kg-K. a....

A: use formula P=pRT

Q: The table below shows the observed rainfall intensity on a 2.26 km2 catchment area. Estimate the o i...

A: Hello dear this is the solution of your problem The answer is found to be Phi-index for given rainfa...

Q: At 20°C, there is a gap d = 0.2 mm between the lower end of the bronze bar and the rigid slab suppor...

Q: Draw the shear and moment diagram, and the elastic curve of the loaded frame shown. Show complete so...

Q: What are mass or weight properties?

Q: Following are the data of gauge and discharge collected at a particular section of the river by stre...

A: Given, stage-discharge data as, Discharge (cms) Gauge reading (m) 20 6.4 40 6.4 76 6.5 ...

Q: Calculate the support reactions for the indeterminate beam shown.

Q: THE BEAM SHOWN BELOW HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fc=13.5 MPa, fy=400 MPa, fs=200MPa. ...

A: A T-beam utilized in development, is a heap bearing construction of built up cement, wood or metal, ...

Q: Determine the Deflection at C. Use the Any Geometric Method (once for DIM, once for AMM, once for CB...

A: Given, E=200 GPaI=250×106 mm4

Q: A 750mm dia. pipe 1162m long carrying 2.4 cubic meter per second of water branches into two pipes, 4...

Q: Transpiration is a physical process not a metabolic process. O True O False

A: Transpiration is the process of movement of water through a plant and water evaporating through leav...

Q: ous beam or spans as snown Is loaded Il the figure as shown below. If EI is constant throughout the ...

A: The three-moment equation expresses the relation between bending moments at three successive support...

Q: Solve for the Concrete Materials (Cement, Sand, and Gravel) of all the Beams on the 2d floor framing...

Q: Which of the following sections is best used as a tension member? Do not consider any loading

A: Given data: Steel section given.

Q: Give an actual example of a scenario (in civil engineering practice) where an honorarium is given to...

A: An honorarium is a contribution paid ex gratia, that is, without the presenter acknowledging any dut...

Q: At 200C, there is a gap d = 0.2 mm between the lower end of the bronze bar and the rigid slab suppor...

Q: Draw a Stress – Strain Diagram with complete details (limits, ranges, regions, etc.) and discuss eac...

Q: 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum axial stress...

A: Load resisted by bolts will transfer through Plate .

Q: In a cultivated area, the soil has porosity of 45% and field capacity of 38%. For a particular crop,...

Q: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 ...

A: Given, b=d2fc=9 MPafs=124 MPan=11φ=20 mm

Q: The area of the reservoir in problem 4 is 3.0km2. The plant supplies a load of 12MW for 3h. Calculat...

Q: Which of the following statements is INCORRECT about the mass transfer method of estimating. evapora...

Q: Assume a turtle can move at an average speed of 0.100m/s while a hare can move at a speed of 15m/s. ...

A: It is required to find the time in seconds the hare has to wait for the turtle to catch up

Q: Ug Two similar round bars A and Bare each 30 cm long and loaded as shown in the given figure. The ra...

Q: It is estimated that the population, daily water demand per capita and service factor at Taman Sivar...

Q: Computer the travel time using the Sheet Flow Method for a 25-year design storm. Assume the project ...

A: Travel Time or Time of concentration : 1. Time of concentration is a concept used in hydrology to me...

Q: Based on the figure given, determine the removal efficiency of the settling column if the overflow r...

A: GIVEN OVER FLOW RATE SO ACORDING TO THAT PLOT A GRAPH

Q: Calculate the support reactions for the following structure using Castigliano's First Theorem. E and...

A: SI = 1 Hence, taking RA as redundant.

Q: 3000 psi, n= 9, M= 70 ft-k.

A: fc'=3000 psin =9 , M =70 ft-k ascertain the bending stresses in the pillar utilizing transformed ...

Q: A Clay soil is found to have a liquid limit of 83%, a plastic limit of 45% and a shrinkage limit of ...

Q: Determine the minimum cross section required for a rectangular beam from a shear standpoint so that ...

A: The values given in the question are as follows: Shear force(Vu)=132 kN Characteristic compressive s...

Q: Draw the axial force, shear and moment diagram of the figure shown.

A: If a load is applied to the structure along the length or perpendicular to the cross-section of the ...

Q: Computer the travel time using the SCS Method for a 25-year design storm. Location Slope (%) Length ...

A: Given, Land use data

Q: A spherical pressure vessel has an inside diameter of 6 m and a wall thickness of 15 mm. The vessel ...

Q: TO BEARINGS. The following six 15. CONVERTING AZIMUTHS iines have their azimuths reckoned from north...

Q: The following offsets were taken from a chain line to an irregular boundary line at an interval of 1...

A: Given data: 0, 2.5, 3.5, 5, 4.6, 3.2,0 interval =10m

Q: 1. As the fluid flows through the section, describe how the velocity, pressure, and elevation heads ...

A: Step: 1 “Since you have asked multiple questions, we will solve the first question for you. If you w...

Q: 2. For the alignment shown below, give the station of the PC and PT of both curves. The station of t...

Q: Determine the forces and moments at point C and point D. For the "SN kn/m" the given is 66 kn/m

Q: A beam is loaded as shown in figure below: wo A B 2 2 R2 R, The moment at B (MB) will be

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Figure shows a rectangular beam section 10 cm wide and 20 cm deep. If the
maximum flexural stress is 80 kg/cm2. What will be total force on area shaded and
moment of this force about the neutral axis respectively.
5 cm
+ N-
A
-10 cm
10 cm
10 cm
5 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 5-m propped beam carries a uniformly distributed load equal to 45 kN/m applied throughout the beam. If the reaction at the roller is 84.375 kN, what is the maximum flexural shear stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa)
Determine the maximum bending stresses for a rectangular beam (20x40cm) subjected to a bending moment Mz = 60 kN.m.
Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft . The average weight of each floor and roof are 95 Ib/ft and 75 lb/ft?, respectively. The 84 ft-tall building is located in a seismic region with SDs =1.6 g and SD1 =0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor I=1.0 Determine the total design seismic force (kips) acting at the base of the building ( seismic base shear in kips). ***the answer was between 339.5 and 342.5*** but I don’t understand how . Handwritten work is preferred
Question 3 5 pts What is the larger vertical reaction of a 6- m simply-supported beam carryinga triangular load which varies from 0 at one support and 15 kN/m at the other support? (Answer must be in kN.)
In Step 6, sum of vertical forces, looks like you forgot an 8kip downward load
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Given a bar X with length 3.7 meters, determine where the 3.2 kN force must be applied in order for the bar X whose mass is being neglected, will be in equilibrium in a horizontal position. Solve using equilibrium of non-concurrent force system. With accurate fbd please, thank you.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Calculate the section modulus of a beam if a moment of 250 kN.m causes a bending stress of 50 MPa. A cantilever beam subjected to a concentrated load at the end of its 6m length. If the allowable shearing stress at the neutral axis is 2MPa, Determine the allowable load P it can carry. Use a flange thickness of 100 mm.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.