Figure shows the members of a truss structure, subjected to a vertical load of 100 kN as shown. Calculate the displacements of node, A using Matrix Method. The cross sectional area of each member is 0.001 m2 and modulus of elasticity of the material (E) is 2.0 x 108 kN/m2. Lengths AB = 3.0 m, AC = 3.464 m; AD = 4.243 m%3; %3D AE = 6.0 m. Angles BAC 30°; BAD = 45°; BAE = 60°. C A В х 100 kN

Figure shows the members of a truss structure, subjected to a vertical load of 100 kN as shown. Calculate the displacements of node, A using Matrix Method. The cross sectional area of each member is 0.001 m2 and modulus of elasticity of the material (E) is 2.0 x 108 kN/m2. Lengths AB = 3.0 m, AC = 3.464 m; AD = 4.243 m%3; %3D AE = 6.0 m. Angles BAC 30°; BAD = 45°; BAE = 60°. C A В х 100 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200 Gpa. Use Catigliano's Theorem. Determine the vertical displacement of joint C if a P force is applied to the truss at C If no loads act on the truss, what would be the vertical displacement of joint C if member AB were 8 mm too short.(use data at ¶N/¶P) If P force and fabrication error are both accounted, what would be the vertical displacement of joint C
The force of an inverted L-shaped structure is shown in the figure below. Try to calculate the vertical and horizontal displacements of the bending moment C. The E of the entire structural section is 200 GPa, and the I is 240×10^6 mm^4.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
If you want to determine the magnitudes of all the forces shown on the structure, which one of the three step process, in the order it is presented, is the most efficient method? (Assume you know the weight of the structure) Group of answer choices Use force summation i) first along x, ii) then along y, and iii) lastly take moment summation along z axis i) First take force summation along x; ii) then take force summation along y; iii) lastly take moment summation at point A. i) First take force summation along x; ii) then take moment summation at A; iii) lastly take moment summation at point B. i) First take moment summation at point O; ii) then take moment summation at A; iii) lastly take moment summation at point B.
For the plane truss given below, using the Matrix Stiffness Analysis method, determine;• Determine displacements of the joints Note that the whole system has 4 nodes and hence 8 degrees of freedom. These degrees of freedoms are shown (in their positive directions) on the right hand side of the problem picture (1 to 8). So, the system stiffness matrix, K, will be 8x8 in size. Force and displacement units should be consistent (mm’s and N’s for example
The frame given in the figure below has three degrees of freedom in C (1,2,3) and three degrees of freedom in B (4,5,6) .In Figure 1:Open the vertical deformation at node C and apply force F and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method What is the status of the forces and moment on the CD in C? In other words, what is the ratio of forces R1 F R3 R4 R5 R6 Apply to CD column in C? And what is the position of the forces and anchors on BC in B and C? In other words, what is the ratio of forces R1 F R3 R4 R5 R6 Applied to BC beams in C and B? In Figure 2:Open the rotation at node C and insert the momentM and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method What is the status of the forces and moment on the CD in C? In other words, what is the ratio of forces R1 R2 M R4 R5 R6 Apply to CD column in C? And what is the position of the forces and…
In the figure, compute the vertical and horizontal components of displacement of joint E produced by the loads. The area of bars AB, BD, and CD = 5 in^2 , the area of all other bars = 3 in^2. E = 30,000 kips/in^2 . Use Castigliano's Second Theorem to find the; - Vertical Displacement at Joint E - Horizontal Displacement at Joint E
There is a structure composed of beam (AC) and truss (BD) as shown in the figure below. After trying to calculate the force: (1) the vertical displacement of point C, (2) if you want to extend (or shorten) the truss (BD) in advance To offset the displacement of point C, what is the amount of elongation (or shortening)? Assuming that the E of the entire structural section is 29,000 kips/inch^2, the I of the beam (AC) section is 340 in^4, and the truss (BD) section A is 5 in^2
use the stiffness matrix method to find the displacement at node 1,2,3,4 K1= 8 N/mm K2= 12 N/mm K3= 20 N/mm K4= 15 N/mm K5= 35 N/mm P = 1000 N
There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.
The bar shown determines: a) The internal force in section AB, BC and CD. b) The approach or distance between points B and C, and between points C and D. c) The displacement of points A, B, C and D. d) Conceptually, what is the difference between deformation and displacement? Consider: Cross-sectional area of the bar A=50 mm2 , Modulus of elasticity E = 200 x109Pa
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️