The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200 Gpa. Use Catigliano's Theorem. Determine the vertical displacement of joint C if a P force is applied to the truss at C  If no loads act on the truss, what would be the vertical displacement of joint C if member AB were 8 mm too short.(use data at ¶N/¶P)  If P force and fabrication error are both accounted, what would be the vertical displacement of joint C

Q: Question Lead as a material used in construction has E= 15 GPa and K= 50 GPa. What its Poisson's…

A: Given data: Elastic modulation, E=15 GPa. And K = 50 GPa. Poisson's ratio, μ=?

Q: A 6 3 8 2 w1 kN/m kN/m kN/m KN m x1 3m B x2 2m x3 1m

A: to find support reaction at joint A,B and C

Q: etermine the forces in members CH and CF. The forces are positive if in tension, negative if in…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given data  Find force in each member in N.

Q: 5 October 2022 at 1:00 pm The length of tape is decreased by 0.0008 m at a temperature of 25°C. At…

A: Using formula to find elongation of tape due to temperature rise

Q: 1. 150 KN 150 KN The to to DE 90 kN/m -2.4 m- 0.8 m 0.8 m -0.8 m I W460 x 113 Draw the shear and…

A:

Q: Given the truss below what are the internal force members of members BF, AB and AD. Determine…

A:

Q: A composite beam is fabricated by bolting two 2.7-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: 10-m-long steel rails of a railroad track (E,= 200 GPa and a = 117 x 10°C) were laid at a…

A: Using formula to find stress due to temperature rise

Q: For a given elextic material, the Eastic Modulus E is 210 GPa and its Poission's Ratio is 0.27. What…

A:

Q: A dam is subjected to a varying load as shown w1 kN/m w1 w2 w3 X y X (x+3) m 6 15 25 10 12 w2 kN/m y…

A:

Q: Problem 3. A circular railway curve has to be set out to pass through a point which is 40m from the…

A:

Q: Determine whether each of the beams and frames below are externally determinate, indeterminate, or…

A: Finding external indeterminacy

Q: A dam is subjected to a varying load as shown w1 kN/m w1 w2 w3 X y (x+3) m kN/m kN/m kN/m 6 12 20 7…

A: W1 = 6 kN/m W2 = 12 kN/m W3 = 20 kN/m X = 7 m Y = 12 m to determine  Vertical force Horizontal…

Q: In a simply supported beam of 10 m span having udl of 8 kN/m, the maximum Bending Moment shall be 80…

A: Given, A simply supported beam,  L= 10m Udl= 8kN/m To find :- maximum bending moment

Q: Given the following cross-section notes for a road grading work: -3.2 X + 1.2 0 + 1.2 3.5 + 2.8 X₂…

A:

Q: Find roller support reaction

A: Given: A=5B=8 One side over hanging beam with roller support at A and hinge support at B carrying…

Q: lease answer will durely given an upvote

A: In conjugate beam method, real beam is converted to conjugate beam by changing support condition of…

Q: The length of tape is decreased by 0.0008 m at a temperature of 25°C. At what temperature will it be…

A:

Q: How can a wind load be applied on building bents?

A: Wind load: The building stands against a wind force acting on the elevation. The wind force absorbed…

Q: 9.18 A steel rodin. in diameter and 25 ft long is subjected to an axial tensile load of 15,000 lb.…

A: Given: Rod diameter, D = 3/4 in  Length of the bar, L = 25 ft Load, P = 15000 lb Take young's…

Q: Q3. A slope inclined at 16° to the horizontal is to made in a cohesionless deposit having following…

A:

Q: The uniform 5.3-m pole has a mass of 260 kg and is supported as shown. Calculate the force P…

A:

Q: Draw the influence diagram for members L3L4 and L4L5 due to a single moving load on a simple truss…

A:

Q: Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is…

A:

Q: An eight-lane freeway has a capacity of 8000 vehicles hour in each direction under normal…

A: Given Data: The data is given as: Time period 8:00-8:15 8:15-8:30 8:30-8:45 8:45-9:00 9:00-9:15…

Q: The 5-ft concrete post is reinforced with six steel bars, each with a -in. diameter. Knowing that E₁…

A: Given,  Total steel bar 6 number of diameter = 7/8 inch Es = 29x10^6 Ec = 3.6x10^6 Centric force (P)…

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

A:

Q: Situation #1 El is Constant (Assume El = 1 kN-m²) Y KN 3 m 7 10 + A X KN 4 m B Y= 32 X= 868 A= 5 4.…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Note that the sign convention for shear stress has been taken as ANTICLOCKWISE POSITIVE .   If it…

Q: 3 KN 2kMi # 3 m 4KN 8 3m W aku 3m 3 KN VE f 3M

A: GIVEN :- the above truss loading are shown.                 we are find the forces in members in GB,…

Q: Select the lightest W shape

A: Given, Fy = 350 MPa L = 4.90 m

Q: Problem 5. If the center lines of the two parallel railway lines that are connected by a reverse…

A:

Q: Solver for Axial force at column EA. Shear force at girder EF. End moment at girder EF.

A:

Q: The 36-kg homogeneous smooth sphere rests on the 26° incline A and bears against the smooth vertical…

A:

Q: Please show a step by step solution. Kindly use a formula that can clearly understand the solution.…

A: V1 = 3.5ft3 T1 = 500F T2 = 1500F     To determine -  Percentage change in volume Weight of water…

Q: Determine the reactions in supports A and D and connections B and C. 30 kN/m B 3 m 65 KN 3 m C 5 m…

A:

Q: 3. A steel beam is use to carry a uniform load of 25 kN/m over a span of 6 m. The left support must…

A:

Q: Question An effluent at a flow rate of 2670 m³/d from a sewage treatment plant is to be disinfected.…

A: Given data- Flow rate- Q=2670 m3/d,chlorine dose=15 mg/L,Nt=Noe-0.145t, Nt=number of micro-organisms…

Q: In a simply supported beam of 10 m span having udl of 8 kN/m, the maximum Bending Moment shall be 80…

A: Given :  Simply supported beam Load = uniformly distributed load (udl) (W) = 8kN/m   Length of…

Q: Determine the force in member BF (in kN, round-off to 2 decimal places, include "-" if in…

A:

Q: 5. Compute the slope and deflection at 2 m from the left support on the beam loaded and supported as…

A:

Q: .80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the ottom of the tank as shown. Assume…

A: To find pressure difference at point A and B

Q: Current Attempt in Progress Calculate the forces in members BC, BE, and EF. Solve for each force…

A:

Q: Problem 3. A circular railway curve has to be set out to pass through a point which is 40m from the…

A: Solution attached below

Q: Problem-2 Determine the load P such that the members in the three-hinged arch shown below are in…

A: To determine -  Load P and value of y1.

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

A:

Q: A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld…

A: Given- Size of weld=8 mm, safe stress=110 N/mm2, It is needed to find the value of the safe force.

Q: From the given figure; E = 200 Gpa, I = 60x10^6 mm^4 a. Determine the deflection at point D in mm.…

A:

Q: etermine the range of weights W for which the 100-lb block is in equilibrium. All wheels and pulleys…

A:

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.