Figure shows the water flows through a pipe AB with a 1.2 m diameter at 3 m/s and then passes through a pipe BC which is 1.5 m in diameter. At C the pipe forks, Branch CD is 0.8 m in diameter and carriès one third of flow in AB. The velocity in branch CE is 2.5 m/s. Calculate: (i) the flow rate in AB (ii) the velocity in BC (iii) the velocity in CD (iv) the diameter of CE Qu ? Vas 3 m/s daR = 1.2 m Vac ? dac 1.5 m QcD 1/3QAR VCD=? deD 0.8 m D C VCE 2.5 m/s dc=? QAB = 3.393 m/s VBC = 1.92 m/s VCD %3D = 2.25 m/s DCE = 1.073 m

Figure shows the water flows through a pipe AB with a 1.2 m diameter at 3 m/s and then passes through a pipe BC which is 1.5 m in diameter. At C the pipe forks, Branch CD is 0.8 m in diameter and carriès one third of flow in AB. The velocity in branch CE is 2.5 m/s. Calculate: (i) the flow rate in AB (ii) the velocity in BC (iii) the velocity in CD (iv) the diameter of CE Qu ? Vas 3 m/s daR = 1.2 m Vac ? dac 1.5 m QcD 1/3QAR VCD=? deD 0.8 m D C VCE 2.5 m/s dc=? QAB = 3.393 m/s VBC = 1.92 m/s VCD %3D = 2.25 m/s DCE = 1.073 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A channel carries water which is forced to pass under a structure, such asShow in Fig. 2. Neglecting energy losses, calculate the pressure in thepoint 1, knowing that the speed at point 2 is 2 m/s. Data Z1 = 0.8m; L1= 1.5 m and L2 = 1.0 m.
A valve is placed at the downstream end of a 3 kM long pipeline. Water is initially flowing along the pipe at a velocity of 2,5 m/s. what is the magnitude of the surge generated by a sudden and complete valve closure. For water K = 2100 x 106 N/m2 and density, ρ = 1000 kg/m3.
The parabolic velocity distribution in a channel flow is given by u(y) = 0.2(1 − y^2) m/s with y measured incentimeters. What is the acceleration of a fluid particle on the centerline where y = 0? At a location where y = 0.5cm?
Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
1. The water flows through a pipeline 1.2m diameter at a velocity of 3m/swhich bifurcates at a Y-junction into two branches. The first branch is 0.8min diameter and carries 1/3 of the flow, whereas the second branch carriesthe water in a velocity of 2.4m/s. Calculate the following: (i) discharge (ii) velocity in the first branch (iii) diameter of the second branch
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
Water flows through a circular pipe with a constant radius of 10cm. The speed and pressure at point A is 4m/s and 250,000Pa respectively.a. What is the speed of the fluid at Point B? b. What is the pressure at point B which is 10m higher than point A?
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cv. a.0.636 b.0.629 c.0.98 d.0.989 PLEASE INCLUDE FIGURE OR FBD
Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
Water flows smoothly through a pipe with various circular cross-sections of diameters 2D, 6D, and D`, respectively. a.) What is the ratio of the speed in section 3 to the speed in section 1? V3/V1= b.) In which section is the pressure largest? Choose the best answer. a.) They are the same b.) Section 1 c.) Section 2 d.) Section 3
Water is passing through a vertical nozzle.The flow rate is 40kg/s and the cross section area at the inlet and outlet is given as 149 and 36cm^2 respectively. The outlet area of the nozzle is open to the atmosphere. Please compute the horizontal component of the anchoring force.