Find metal removal rate is sur face grinding of a(300mm) long and (60mm) width of rectangulare steel work Piece whose speed is (15 m/min) defth of (cut 0.05mm) and width of grinding pathz lomm? =

Q: According to vapor compression refrigeration cycle, Refrigerant-134a enters the adiabatic compressor…

A:

Q: Determine the natural period of vibration of the uniform bar of mass m when it is displaced…

A: Consider the diagram shown below for the small angular displacement of the rod.

Q: determine how long (in years) it will take to exhaust this natural gas well.

A:

Q: The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial…

A:

Q: ) Find the steady state temperature, u(r, 0), in the plate shown in the following figure.

A: The boundary value problem is

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7…

A: Diameter of tie rod (1) = 7 mmDiameter of pin B = 5 mmLengths:a = 670 mmb = 335 mmh = 370 mmAngle=to…

Q: Determine the required magnitude of force F if the resultant couple moment on the frame is 200…

A: Given the Resultant couple moment on frame = 200 lb.ft(clockwise)The Forces on frame as given:To…

Q: Compressed air enters a 0.2 m diameter circular air duct at a temperature of 20°C and a pressure of…

A:

Q: Q3:Air flows over the flat plate at velocity 0.3 m/s and ambint temperature 15 C.The plate is…

A:

Q: In a single-stage gear wheel system with an evolvent profile, the rotating (drive The number of…

A: please refer handwritten solution

Q: The mass , is connected to two springs of stiffness k1 and k2. The free ends of the springs undergo…

A: The free ends of the springs undergo the harmonic displacements, y= Ysinwt and y2=Y2sinwt. to…

Q: 2. Consider the streamfunction (with u = 3y and v = -) and a coordinate transform from (x, y) to (x,…

A: Flat plate laminar boundary layer U = dΨ/duv = dΦ/ dx

Q: A skier is pulled by a rope exerting a horizontal force T=[T] KN at a distance h= [h] cm above the…

A: Given:To find:Critical load T

Q: Find frequency and mode shape for the system shown in Fig. 5, using Stodola process. Take m= 1 kg;…

A: The mass, m = 1 kgThe stiffness, k = 1000 N/m

Q: ease locate the x' axis of the composite area of this funky shape. 5 in. 2 in. 2 1 in. 1 in. |--3…

A:

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A:

Q: alculate the power in the compressor, W(kW) Calculate the power-heat in the exchanger, Q(kW)…

A: Given data is

Q: Keeping in mind continuity of flow, compute the velocity of flow for section C (Vc), the 6 inch…

A: Given Data

Q: A pump is driven by an electric motor through a open type flat belt drive. Motor pulley diameter…

A:

Q: 14. The figure below shows an iron ball suspended by thread of negligible mass from an upright…

A:

Q: Q1. Propane (C3H8) gas enters a steady-flow adiabatic combustion chamber at 25°C and 1 atm. It is…

A: Initial temperature = 25 CExcess air = 300 %Excess air temperature = 25 CIt is asked to find the…

Q: = Determine the magnitude of the equivalent force at point B. Take F₁ 120 lb, F3 = 70 lb, F4 = 40…

A:

Q: The volume in the clearance space of a 6 by 10-inches Otto gas engine is 0.06 ft3. Find the ideal…

A:

Q: In the figure below, the arm CD of the pipe is parallel to the z axis. The cross-section of the pipe…

A: Given Data:Inner radius of Pipe Outer radius of Pipe Find:(A) Stresses on point A(B) Stresses on…

Q: Draw shear force (V-x) and bending moment diagrams (M-x) for beams and loads in Figure 3.

A:

Q: 4-62 1 kg of oxygen is heated from 20 to 120°C. Determine the amount of heat transfer required when…

A: For oxygenm= 1 kgT1=200 CT2=1200 CThe specific heats of oxygen at the average temperature of…

Q: 2) In figure, two blocks are connected by a massless string over a pulley of radius, 2R, and…

A:

Q: In a mine, a 100 kg boulder is transported at a velocity of VA=0.1 m/s before it slides down a chute…

A: Given:To find:velocity of boulder

Q: 5. For the system shown below, what steady-state error can be expected for the following test…

A:

Q: Calculate the support reactions at A and B for the loaded beam. Assume P = 143 lb, w = 92 lb/ft, a =…

A:

Q: The tension in cable AB is 900 N. What is the component of force from this tension in the positive x…

A: Given data-tension in cable AB is= 900 NDetermine- component of force from this tension in the…

Q: Consider 5.2 pounds per minute of water vapor at 100 lbf/in², 500°F, and a velocity of 100 ft/s…

A: Given:The mass flow rate is The pressure at entry is .The temperature is .The velocity is .The…

Q: The two wooden members shown in the figure support a load of 16kN and are are joined by sheets of…

A: load, P=16kNultimate shear stress of the glue = 2.5 MPafactor of safety. FOS=2.75clearance between…

Q: Determine the torque output of a 25-hp motor rotating at 1250-RPM. 142.3 N-m 191 N-m 3.27 N-m 1260…

A: The power of the motor, (P)=25 hp.The rotational speed of the motor, (N)=1250 rpm.Determine the…

Q: Compound axial member ABC has a uniform diameter of d = 1.45 in. Segment (1) is an aluminum [E₁ =…

A:

Q: Draw the sectional view of the solid and provide necessary dimensions. E 7 Scale 1:2 Draw the…

A: According to the given datatwo object views are givenWe need to draw the section view of the problem

Q: load scenario A cut 3.92 N -Y 140mm * D'Y RA 300mm shear force. SFul-3.92+5.9493. SFeut-1.8293 N IRB…

A: Note:-  As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: can tutor explain the questions more detailed

A: Weight on the wing, W = 80 KNLift force on the wing, F = 100 kNThe cross-sectional area of the wing,…

Q: Determine the deflection in inches of a .75" diameter steel shaft 13" long subject to an axial force…

A: Given, Shaft diameter is 0.75 inch Length of shaft is 13 inch Axial force is 1600 N Required:…

Q: If the position of a particle is defined by r [(1.5t² + 1)i + (4t - 1) j] (m), its speed at t = 1 s…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A:

Q: A wagon weighing 5100 Kg moving at a speed of 8 km/h has to be brought to rest. Springs made of wire…

A:

Q: power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance…

A:

Q: Determine the angle of twist (degrees) of a .75" diameter steel shaft, 13" long subject to a 1200…

A: The angle of twist.Given:The diameter of the shaft is .The length of the shaft is .The torque is…

Q: A rectangular nylon [E = 8 GPa; v = 0.35; d = 29 x 10-6/°C] plate has a circular hole in its center.…

A: Given data :-Diameter (d) = 55 mmThickness of plate (t) = 21 mmThermal coefficient = 29*10-6/°CTf…

Q: Consider 4.8 pounds per minute of water vapor at 100 lbf/in², 500°F, and a velocity of 100 ft/s…

A: We are given the following data for water entering a nozzle :From Superheated Water From Superheated…

Q: 1) The cantilever truss is loaded with P as shown in the figure. The load P is 19.99kN. Determine…

A: Given data is

Q: Explain how intergranular precipitation leads to intergranular Stress corrosion cracking (IG Stress…

A: Intergranular precipitation and intergranular stress corrosion cracking (IGSCC) in austenitic…

Q: QUESTION 3 A system increases in volume from 5 m3 to 2 m³. Assuming that the pressure in the sytsem…

A:

Q: Determinn the setillest dimension d that will prevent the dam hom overturning about is end  A.

A: GivenThe density of concrete is The density of the water  a=1 mh=8 mConsider, The length of the…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.