Answered: Find Real, Reactive and Apparent power…

Find Real, Reactive and Apparent power for following load configuration. Iline 2300 V Motor 50 hp 0.84 lagging Fan 13 kW 0.75 lagging Heating 24 kW unity

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 7PP: Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.

See similar textbooks

Related questions

Q: 1. The phasor diagram representing four alternating currents is shown in the figure below where the…

Q: For the following op-amp circuit RI (i) What is the function of the circuit? (ii) (iii) (iv) it R2…

A: We need to find out the function of given circuit , gain for given circuit . Cut off frequency for…

Q: input 1 1 1 impurtro inio Present State @Find Q 0 4 11 input: 0 a insh Clo inel by 1 inct Next store…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 6. Determine the output voltage vo in the circuit below. Hint: Begin with a node equation at the +…

A: In this question, We need to determine the output voltage Vo as shown the circuit. We are…

Q: Q4) Reduce the following Boolean expressions to the indicated number of literals: (a) (x' y + 2) +z…

Q: 1.) A lobby is 20 ft by 22 ft with an 8 ft ceiling. You want to determine the average illuminance on…

A: Given, Length of the lobby,L=20 ft The width of the lobby, W=22 ft Height of the ceiling, H=8 ft

Q: 7. Calculate ₁, ₂, and is from the following circuit. 60 20 12V 40 6V

A: Mark the node and redraw the given circuit as:

Q: v(1) 192 oooo 1Η 1 H 0000 192 ww 1 H elle + VL (1) FIGURE 2.14 Electric circuit for Skill-…

A: We need to find out the voltage ratio for given circuit.

Q: Three single-phase distribution transformers, each rated for 18 kVA, 20000/220 volts, are connected…

A: Three single-phase distribution transformers are connected in a Dy three-phase bank. Rated power…

Q: A 5-nC póint charge is located at A(2, -1, -3) in free space. (a) Find E at the origin. (b) Plot…

Q: Find the mid frequency gain (Am) in dB and the high-frequency cutoff frequency (WA) in rad/s for the…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.

Q: 6.33 A p-type silicon sample is doped at Na = 6 x 10¹5 cm-³. It is determined that EF EF= 0.270 eV.…

Q: For the given circuit below, it operates on a peak- to-peak input voltage of 133.1 V, F = 60 Hz…

A: Here we have to find the output peak voltage.

Q: In the given figure, A₁, A₂ and A, are ideal ammeters. If A₂ and A, read 3 A and 4 A respectvely,…

A: Here we have to find reading of A1 .

Q: Time 0.000 s 0.000 s 0.000 Channel A 0.000 V 0.000 V 0.0001 Channel B Reverse Savo

Q: 1. For the following circuit, find (a) v₁, (b) the power of each circuit element. 2A 5V 2V + 2v₁ D:…

A: The given circuit is shown below,

Q: Question 3-) For the circuit shown in Figure below: a-) Obtain the mesh equations using mesh-current…

Q: 2. A 75 MHz carrier having an amplitude of 50 V is modulated by a 3 KHz audio signal having an…

A: In this question, We need to determine modulation index, % modulation index and upper frequency and…

Q: 1. Indicate the main differences between the noninverting, inverting and differential modes of…

A: In the given questions we need to explain about the inverting , non inverting and difference…

Q: What is the difference between full wave controlled and full wave half-controlled rectifier ?

Q: For the signal given below, check whether it is a power signal or an energy signal or neither. X(t)…

Q: A live streaming service is required to broadcast high definition television (HDTV) and stereo audio…

A: Given: A live streaming service is required to broadcast high definition television (HDTV) and…

Q: 4. Explain if any of the two fields aescnoca by the expressions below can describe an electrostatic…

Q: Find 1 and 12 in the circuit below. 10<45°A 202 M i₁ m j30 -j150 M 402

A: For the given circuit calculation of i1 and i2 . By using KVL and KCL and applying source…

Q: 3. Obtain an equation for the output voltage vo in the circuit below in terms of the input voltage…

A: The given circuit is a voltage summer and the required parameter can be obtained by using the KCL…

Q: Three 120 kVA 24,000/277-V distribution transformers are con- nected in A-Y. The open-circuit test…

A: Given data: KVA rating of the three-phase transformer: 120 KVA. Voltage ratio of the transformer:…

Q: Can I ask you to demonstrate how to complete parts d) e) and f) of question 3 as seen in the…

A: It is given that: d) A+B'A'+B''e) ABC+A'B+ABC'f) xy+xwz+wz'

Q: 3- Show the effect of sampling time on the characteristic of ZOH. digital to analog converter

A: The zero-order hold (ZOH) is a mathematical representation of how a common digital-to-analog…

Q: What is Vm ? And how the Vdc become =0.318Vm

A: It is given that:

Q: D 7(5)= X(s) F(s) K₁ m 81 M B₂ 777

Q: 1. For the following circuit find the amplitude of the input voltage which results in Vac = 2 V…

A: Given: For the following circuit: To find: The amplitude of the input voltage which results in Vdc…

Q: You are given a machine to operate having a resistance of 0.25 Q and it is connected to a 300 V…

A: Resistance (R) = 0.25 ohm Voltage (V) = 300 V Ia = 100 A Ia = 80 A

Q: Q1 Q2 Q3 -6 Q5 -16 -6 -6 -54 -4 -8 -2 -4 10 10 -4 10 X(t) -2 -1 10 0 2 X(t) X(t) -10 X(t) 10 24 250…

A: Odd signal: If a signal is symmetric about vertical axis. The signal will be odd signal. e.g- cos…

Q: A cell has an internal resistance of 0.02 ohm and an e.m.f. of 2.0V. Calculate its terminal p.d. if…

A: Given data: The internal resistance of the given cell, RS=0.02 Ω The internal voltage,Vs=2 V The…

Q: A device has an input signal-to-noise ratio of 300 and an output signal-to-noise ratio of 14. What…

A: Signal-to-noise ratio is usually expressed in decibels (dB). The signal-to-noise ratio is a…

Q: The pMOSFET has e) V₁=-IV, AC CIN R₁ 'k' W=0.5mA/V²,V₁0⁰ "L R₁ 1.6 M V R₂ 820k DD = 10V Rs 2K W f)…

A: As per your requirement I am solving only d,e,f as shown below.

Q: R3 M Rs. lo -Vss For the current source above, R 3 =158Kohm, R 4 -194Kohm, Rs-6Kohm. If the…

Q: Consider a bar of p-type silicon that is uniformly doped to a value of N₂ = 2 × 10¹6 cm-3 at T = 300…

A: Given: Na=2×1016 cm-3, T=300 K, Applied electric field is "0",δp0=δn0=2×1014 cm-3, μn=1200…

Q: The amplifier circuit shown below has the following parameters: Rid = 200k, r. = 2k, an open loop…

A: The amplifier circuit is given as Given that Internal input resistance of the…

Q: Given: GH ll IK, <KGI = <HIG Prove: GH = IK

A: It is given that: GH∥IK,∠KGI=∠HIG ...... 1,

Q: For the given circuit below, it operates on a peak- to-peak input voltage of 133.1 V, F = 60 Hz…

Q: A direct voltage source that has an output resistance of 125 Ω is connected to a circuit that has an…

A: Given that, Output resistance=125Ω, Input resistance=3000 Ω, Input voltage=10V Sensitivity of…

Q: Consider the two periodic time functions x₁ (t) and x₂(t) shown in the plot below. Note that -20 -10…

Q: 1. The forward bias voltage (FBV) in the circuit below is OV. Determine the transfer function at A…

A: The required plot can be drawn based on the conduction of diode in forward and reverse bias.

Q: Calculate the value of in the following circuit, for the following values of current and resistance:…

A: It is given that:

Q: Find the value of Ry that will produce the indicated closed-loop gain in each amplifier in figures…

Q: Determine the circuit rating for the following appliances or equipment on a 277 V circuit: Eight…

A: Given data: The voltage,V=277 V The power consumption = 138 W The number = 8 (4 - 32 W)

Q: Problem 4 Find the Thevenin and Norton equivalent circuits for the circuit shown below. Find the…

Q: Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent…

A: Single phase transformer works on the principle of Electromagnetic Induction and has primary side…

Q: In the circuit of the given figure, assume that the diodes are ideal and the meter is an average…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Find Real, Reactive and Apparent power for following load configuration.
Iline
2300 V
Motor
50 hp
0.84 lagging
Fan
13 kW
0.75 lagging
Heating
24 kW
unity

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Type your question here A power plant has to meet the following load demand: Load A: 100 MW from 8 AM - 6 PM Load B: 150 MW from 6 AM - 10 AM Load C: 50 MW from 6 AM - 10 AM Load D: 20 MW from 10 AM - 6 AM Plot the daily load curve and determine (a) diversity factor (b) load factor (c) daily energy produced.
Calculate the real and reactive powers of the load between terminals a and b in the given figure. Assume f = 60 Hz, V∼S�∼� = 70∠0 V rms, RS = 2 ohm, Ro = 26 ohm, and XL = 5 ohm. The real and reactive powers are _______W and _________VAR.
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
Given a tee connected system with power factor of 80 percent and true power of 2,500 kW. Calculate the reactive power.
•••PF improved by 100% Convert the given load of the circuit shown into impedance bulk by using power triangle; f= 60hz. Measure the line current IL, power loss PL0, power source Ps, voltage source VS; take note of the old value of PFL; Notations IL= line current; PL0= power loss; PS= power source; VS= voltage source; PFnew= New power factor after correction; PFold= old power factor before correction
Visible power of Z1 = |S1| = 16 kVA and at 0.8 back power factor; Visible power of Z2 = |S2| = 25 kVA and operates at unit power factor; Loads ZW = 5 + j26ohm/conductor is connected to the source by transmission line; VL = 3.8 kV Find the visible power of source,power factor and rms of source
Question oneA balanced star connected load comprises of 20 ohm resistance and 0.07 Henry inductance in each branch. If the load supplied with 415V at 50Hz, calculatea) the line currentb) the power factorc) the total power supplied to the load PLEASE FOLLOW THIS APPROACH TO SOLVE THE QUESTION. THANK YOUStep OneDeduce the inductive reactance.STEP TwoWrite down a rectangular expression for the impedance per branch.STEP ThreeConvert the rectangular expression into polar expression.STEP FourBecause impedance will be involved in the analysis deduce the phase voltage.STEP FiveSolve for the phase current and hence the line current.STEPVSixUse the phase angle of the current to deduce the power factor. STEP SevenFind the apparent power.
Assume that vg = 120 V rms. Finda. The secondary current.b. The installation efficiency Pload/Psource.c. The value of the load resistance which can absorbthe maximum power from the given source.
A residential four-wire system supplies power at 220 V rms to the following single-phase appliances: On the first phase, there are ten 60-W bulbs. On the second phase, there is a 1-kW vacuum cleaner with a power factor of 0.9. On the third phase, there are ten 23-W compact fluorescent lamps with power factor of 0.61. Find a. The current in the neutral wire. b. The real, reactive, and apparent power for each phase.
A power station has to meet the following load demand : Load A 50 kW between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (i) diversity factor (ii) units generated per day (iii) load factor.