Find the area of the largest circle which can be cut from a square of edge 5 in. What is the area of the material wasted?

Q: Determine the centroid of the given composite figure. The area of the geometric figures drawn in red…

A:

Q: An open rectangular Bốx is to bê made from a 9 x 12 inch piece of tin by cutting a square of side x…

A:

Q: Line rods or range poles are made up of?

A: Range poles or ranging rods as they are sometimes called, is a surveying instrument that is used for…

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Please give the figure with correct label

A: Given that total surface area of cylinder in square feet is equal to it's total volume in cubic…

Q: how did you get the 0.054 lb/in^3 ?

A:

Q: 2 decimal pl

A:

Q: Calculate the area of the section shown below by formulas. E XI X2 h1 h2 C W

A:

Q: A block of wood with length "h" and cross-sectional area "A" is submerged in water with 50mm exposed…

A:

Q: 2 ft I ft 2 ft 1 ft 3 t

A:

Q: Which properties are the most helpful in identifying minerals?  Are these properties helpful in the…

A: Color, hardness, lustre, crystal forms, density, and cleavage are all characteristics that help…

Q: What is the general range of L/G ratios?

A: L/G ratio stand for the liquid to gas ratio. which is the ratio of the waste slurry to the flue gas…

Q: Consider a glass with ice cubes. Sketch its plan, two elevations and a 3D image.

A: Glass with ice cubes- When a glass is filled with ice cubes, it can have many drawing shapes. All…

Q: 1. 30% 511 Given: aA = 3 m/s². = same for each section Unknown: ag = ?

A: given data : acceleration of block at point A is equal to 3 m/s2 we are asked to find to…

Q: Describe the Particle Shapes and Sizes.

A: Particle size refers to the dimensions of particles (solid, liquid and gaseous. It is used for…

Q: A circular piece of tin 24cm in diameter has a triangular hole 9cm by 12cm by 15cm. The vertex of…

A: Diameter = 24cm Sides of vertex - 9cm by 12cm by 15cm

Q: A 100-lb box measuring 12"x 18"x 18", as shown, is placed in water. If the box floats, what is the…

A: Given data, Weight of box = 100 lb Size of box Length L = 18" = 1.5' Width B = 18" = 1.5' Depth H =…

Q: A watermelon 12” in diameter is to be cut in wedges, what would be the area of the cut if the wedge…

A: Diameter (d) = 12” Radius (r) = d/2 = 12/2 = 6 Central angle (θ) = 30 (same for all wedges)

Q: Josh threw the marble vertically upward with a speed of 70 ft/s from a bridge. On the way down, the…

A:

Q: The area of a circle inscribe in a triangle is equal to 113.10 sq cm. Find the max area of the…

A: As for the maximum area triangle in which an area of a circle is inscribed will be an Equilateral…

Q: 4.5lb=?oz

A:

Q: Estimate the quantity and board foot of the studs used in a wall partition 5.80m long and 3.40m…

A:

Q: A tank containing liquid with SG = 1.78 was put on a weighing scale and registered a total weight of…

A:

Q: Define the  Modular ratio ?

A: Modulus of elasticity: The ratio of stress and strain is known as The modulus of elasticity. This is…

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: vo 3ft 30 ft-

A:

Q: What sieve size has the lowest percent passing? (2 decimal places, no need for unit) Blank 1 Blank 1…

A:

Q: A piece of wood (sg = 0.60) 15 cm by 25 cm and 2.0 m long is floating upright in water. Determine…

A:

Q: What is the weight (Ibf) of a cube of stainless steel with 16.5 cm on each edge?

A: Given: Density of stainless steel, ρ=7860 kg/m3 Edge, a=16.5 cm=0.165 m

Q: Draw a line segment 6 inches long. Subdivide it according to the golden ratio.

A: The length of the line segment is 6 inches. Let the length of the longer side be x and the length of…

Q: A rectangular piece of plywood 2000 mm by 3600 mm is cut from one corner to an opposite corner. What…

A: Given data- A rectangular piece of plywood. Dimensions 2000mm×3600mm The plywood is cut from one…

Q: Compute the following Ø.500 +.003 -.001 Tolerance Maximum limit size Minimum limit size Basic size

A: tolerance = 0.004 max limit size = 0.503 min limit size = 0.499 basic size = 0.500     explanation…

Q: would it be possible to show the line measurements in feet? autocad

A: Yes it is possible.

Q: Reinforced Concrete

A: Calculation of moment of inertia and modulus of elasticity for given beam:

Q: x 6m deformed bars? t the correct response: 465 471 461 468

A:

Q: your

A:

Q: A block of wood with length "h" and cross- sectional area "A" is submerged in water with 50mm…

A:

Q: a) Examine each, the two layers of the earth and give examples.  b) Write a short (half a page),…

A: Solution(a)- Layers of the earth- The crust- The crust of the Earth resembles the shell of a…

Q: SKETCH THE FIGURE    AND SHOW THE COMPLETE SOLUTIONS

A: Step: 1 Latitude and departure are the projection of a line in north-south and east-west direction…

Q: When the length of the board is in feet, what is the formula used for G.F? _____

A: Unit conversions ; 1 feet = 12 inches  1 inch = 1/12 feets

Q: Neatly sketch and explain the constructional feature of manually powered material handling equipment…

A: Construction equipment used for the movement, storage, control and protection of materials, goods…

Construction Process

In civil engineering, construction is the combination of art and science, to construct a physical and naturally built environment, starting from the design phase. The construction process falls under the area of building construction, which is a sub-branch of civil engineering. Hence, it is also sometimes called the design and build or design-build process. The work of construction is majorly carried out by civil engineers and design professionals along with a team of works consisting of contractors and subcontractors.