Find the available strength of the S-shape shown. Theholes are for 4-in diameter bolts. Use A36 steel.S15 x 50 (A=14.7 in², tw=0.550 in, t#0.622 in)Ans. LRFD = 476 kips, ASD = 318 kips12" 12"32"obdS15 x 50

Answered: Image /qna-images/answer/15e6a4fd-b7d7-4bba-a205-e1abf51dc2d5.jpg

Find the available strength of the S-shape shown. The holes are for ¾-in diameter bolts. Use A36 steel. S15 x 50 (A=14.7 in?, tw=0.550 in, t=0.622 in) Ans. LRFD = 476 kips, ASD = 318 kips 12" 1½" 32" e d S15 x 50

Find the available strength of the S-shape shown. The holes are for ¾-in diameter bolts. Use A36 steel. S15 x 50 (A=14.7 in?, tw=0.550 in, t=0.622 in) Ans. LRFD = 476 kips, ASD = 318 kips 12" 1½" 32" e d S15 x 50

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.5P

See similar textbooks

Related questions

Q: A circular sewer flowing full to carry a sewage discharge of 0.864 m³/s at a slope of 10 in 20000. A...

Q: construction

A: 1.(i) Resource utilization in the choice of construction materials Resource utilization in the choi...

Q: d backward tangent are N 65°30' E and N 75°40' W, respectively. If the curve is 2° for a full statio...

A: consider figure for solution (a) Degree of curve , D =2.0 deg Radius R = 5729.57/D=2864.785 ...

Q: An oil of viscosity 0.1 Ns/m2 and relative density 0.9 is flowing through a circular pipe of diamete...

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall tran...

A: b = 250mm D = 400 mm (overall depth) d = 400-40 = 360 mm (effective depth)

Q: cylindrical tank for transporting compressed gas has an inside diameter of 360 mm and a wall thickne...

Q: The distance from the pipe wall at which the local velocity is equal to the average velocity for tur...

Q: A cable carrying a load of 10 kN/m run of horizontal span is stretched between supports of 100 m apa...

Q: The sides slope of a trapezoidal open channel is 1 horizontal to 1.732 vertical. The bottom width is...

A: Given data in question Bed slope Side slope Depth Mannings constant To find out Velocity

Q: Flexibility matrix of the beam shown below as: 2) C 1 2 1 8 = 3EI 2 8 If support B settles by A/EI u...

A: Given, Flexibility matrix=δ=13EI1228 Support B settles by ∆EI

Q: For the beam and loading shown, integrate the load distribution to determine (a) the equation of the...

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: A results below were recorded during tensile test for a steel specimen to be used to manufacture wat...

A: Given- Dia of specimen (d) = 0.597 cmLoad at yield point (f) =8.15 kNTo Find-Yield stress (σ)

Q: A vertical flexural member is shown. If F1=6 kips, F2 16 kips, and F3 9 kips, determine the normal s...

A: Given, F1 =6kips F2 = 16 kips F3 = 9 kips Normal stress =0, since it acts along y axis. Normal force...

Q: element for every one meter interva

A: factors that effect on the precision of limited component technique are 1) Geometry of the body - T...

Q: AB, BE and AE of the pin-jointed truss shown in What is the ratio of the forces in the members AB. B...

Q: Determine the allowable load for a steel closed-ended pipe pile, 0.4 m in diameter, driven 20 m int...

A: Calculating the stress value at different location: σ1'=18×5-9.815=40.95 KN/m2σ2'=18×5+18.55-9.8110...

Q: The magnetic bearing of a line AB is N 29°10’ E. The declination is 2°10’ W. What is the true Azimut...

Q: Assume that P- 35 kips and L- 5 ft. Determine the reaction force at C. Assume that El is constant fo...

A: Applying three moment equation to span (1) and span (2)M1L1+2M2(L1+L2)+M3L2+6A1a1¯L1+6A2b2¯L2=0where...

Q: PROBLEM 1 Given the following interior angles (angles-to-the-right) of a five-sided closed polygon...

A: Given Interior angles of a 5 sided closed Traverse. Bearing of Side AB Length of all sides. To Deter...

Q: A simple curve having a radius of 200m have tangents with bearing N10° E and N70° E. The stationing ...

A: Given: The radius of the curve is 200 m. The bearing of the back tangent is N 10o E. The bearing of ...

Q: 15m 3m 2m B A 4m Em D 100KN

Q: Consider a fluid of viscosity p between two circular parallel plates of radii 'R' separated by a dis...

Q: Determine the length, L, of a driven timber pile required to support the load shown in Figure P13.4...

A: Given:- The diameter of the pile = 450 mm The magnitude of the load (P) = 275 kN The required factor...

Q: In your own words, discuss the provision of the OSH standards that says, 1. All appropriate precauti...

A: Brief concept- OSH Standards- Occupational health and safety is a branch of public health concerned ...

Q: 3. A 200-hectare watershed is slated for commercial and business development. Currently the watershe...

Q: How is the concept of Projectile Motion, Cylindrical Components of Curvilinear Motion, Absolute Depe...

A: Projectile Motion : 1. A projectile is an object upon which the only force acting is gravity. There ...

Q: From an economic point of view why is it not prudent to use a modern method such as the GPS and appl...

A: locating the position with the help of 4 satellites is done in the GPS and these can be defined in t...

Q: Select three different materials Soft Hard (Medium) Superhard • Find their main mechanical propertie...

A: Copper is a soft, malleable, and ductile metal with high thermal and electrical conductivity. It is ...

Q: 10 kN/m A В 6 m 6 m

Q: AB, BE and AE of the pin-jointed truss shown in What is the ratio of the forces in the members the f...

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: Advection, diffusion, and reaction in a channel Approximately 50 m3 of an agricultural pesticide wit...

Q: 10KNM 10KN/m 10lN B 2m 2m 1m 20kNm 20.833 22.218 19.167 17.116

Q: 1 Given the following interior angles (angles-to-the-right) of a five-sided closed polygon traverse...

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the exa...

Q: at what maximum speed in kph, could a car pass through a spiral easement curve without overturning i...

A: Given: The radius of curve is 180 m. The super elevation is 0.12 m/m.

Q: Given y = 3x²y – y, the discharge passing between the streamlines through the points (1, 1) and (3, ...

A: Please refer the attached image for complete solution. THANK YOU.

Q: If at 20°C, a droplet of water has pressure difference of 5 kPa, then at same temperature, a cylindr...

Q: the ice above the water surface is 500 cubic meters, what is the total volume of iceberg

Q: Calculate the side widths and cross-sectional area of an embankment to a road with formation width o...

Q: 23 kN/m² to lb/in²

Q: A cable carrying a load of 10 kN/m run of horizontal span is stretched between supports of 100 m apa...

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a s...

Q: If the density of a liquid is 835 kg/m3 find its specific weight and specific gravity

Q: A soil profile consisting of three layers is shown below. Calculate the values of o, u, and o' at po...

Q: Point A in a beam is deformed such that the strain components are ɛx = -1380 µɛ, ɛy = -880 µɛ, Ez = ...

Q: A spherical gas-storage tank with an inside diameter of 26 ft is being constructed to store gas unde...

Q: A venturi meter has an inlet diameter of 31 mm and a throat diameter of 19 mm. It has a mean pressur...

Q: The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad...

Q: The bars AB and AC support the load as shown in the figure. The bars are double-shear pin-supported ...

Q: A propped cantilever beam with overhang as shown in the figure below. Determine the Reaction and Mom...

Q: A closed traverse has the following data: Lines Azimuth Distances (m) N 60°30' W N 80°30' E АВ 68.75...

Question

Find the available strength of the S-shape shown. The
holes are for 4-in diameter bolts. Use A36 steel.
S15 x 50 (A=14.7 in², tw=0.550 in, t#0.622 in)
Ans. LRFD = 476 kips, ASD = 318 kips
12" 12"
32"
ob
d
S15 x 50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in Ø bolts at the usual gage locations. The stagger is 1 1/2 in. (Ans. 2.98 in^2)
An L8 × 4 × 3/4 with two lines of 3/4-in Ø bolts in the long leg and one line of 3/4-in Ø bolts in the short leg. Compute the net area of each of the given members. (Ans. 6.52 in^2)
Determine the effective net area of the L7 × 4 × 1/2 shown in the figure. Assume the holes are for 1-in Ø bolts. Use the U values given in Table 3.2. (Ans. 3.97 in^2)
0.1: An MC9x23.9 is connected with 3 /4-inch diameter bolts as shown below. A572 Grade 50 steel is used. Determine the design strength for the section.
Compute the net area of each of the given members. The 3/4 x 8 plate shown in Fig. P3-9.The holes are for 3/4 in Ø bolts.
An L6 × 6 × 1/2 is used as a tension member, with one gage line of 3/4-in Ø bolts in each leg at the usual gage location (see Table 3.1). What is the minimum amount of stagger, s, necessary so that only one bolt need be subtracted from the gross area of the angle? Compute the net area of this member if the lines of holes are staggered at 3 in. (Ans. s=4.77 in, An = 5.05 in^2)
Determine the tensile capacity of a 200 x 100 x 12 mm angle in S275 steel assuming that the angle is connected through the longer leg by one row of M24 bolts (Fig. 3). (3 bolts in a row and p = 70 mm)
Determine the Net Area for the following Plate Section consider all possible Cases. The Plate thickness is 1-in. and the bolts' diameter is 7/8-in. s = 6.0 " g = 2.0 "
Determine the available strength of an L6 x 4 x 3/4 attached through the long leg to a gusset plate with ten 7/8 in. bolts at a 3 in. spacing in two lines. Use A36 steel. Determine the (a) design strength by LRFD and (b) allowable strength by ASD
Determine the LRFD design strength and the ASD allowable strength . Neglect block shear. A WT8 x 50 of A992 steel having two lines of 7/8-in Ø bolts as shown in Fig. P3-28. There are 4 bolts in each line, 3 in on center.
Determine the smallest net area of the tension member shown in Fig. P3-17.The holes are for 3/4-in Ø bolts at the usual gage locations.The stagger is 1 1/2 in.
A W18 × 35 with two holes in each flange and one in the web, all for 7/8-in Ø bolts. Compute the net area of each of the given members. (Ans. 8.30 in^2)