Circuits 1 HW 7 Q6 Find the average power dissipated in the 200resistor in the circuit seen in Fig. P10.8 ifig = 15 cos 10,000t A.Figure P10.810iisis =2.5 μFig+1 mHsmc200toolsΣ20 Ωidweisst balls

Answered: Image /qna-images/answer/19b31c66-7fbc-4689-8fea-8129b982df40.jpg

Answered: Find the average power dissipated in…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Obtain an expression for the power dissipated in the 10 resistor of Fig10.49
(P 10.20) Calculate the complex power supplied by the voltage source in the circuit diagram if Vg=40cos10^6t V
A linear circuit supplied by a nonsinusoidal source is shown. Find the average power absorbed by the circuit if the source voltage is expressed as vs(t)=100+50 cos(120лt)+25 cos(240πt)+15 cos(360πt).
A sinusoidal voltage is given by the expression v=300 cos(120πt+30∘) V.1. What is the period of the voltage in milliseconds?2. What is the frequency in hertz?3. What is the magnitude of v at t=2.778 ms?4. What is the rms value of v?
The voltage (in Volts) across an element is given as v(t)= 50 cos(6ft +24.7°) whereas the current (in Amps) though the element is i(t) = - 20 sin(6ft +55°); where time, t is the time and f is the frequency in seconds and Hertz respectively. Determine the phase angle between the two harmonic functions
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
20 ohm in a system with a temperature of 280 Kelvin and a bandwidth of 200 MHz. The average value and the RMS value of the noise voltage that will occur in a resistor for microwave frequencies. calculate. Note: The Boltzmann constant should be used as k = 1.380x10 ^ -23 Joules / Kelvin.
A motor draws 680 W at 156 Vrms 60Hz. The motor is operating at a lagging power factor, with a power factor angle of 45 deg.. Determine the capacitance (in microFarad) required to correct the power factor so that the power factor angle becomes 15 deg, lagging. (Give answer in 2 decimal places. Unit is not required)
The power company supplies 80 kW to an industrial load. The load draws 220 A rms from the transmission line. If the load voltage is 440 V rms and the load power factor is 0.8 lagging, what is the value of the lost power in the transmission line? (Write the value)
A load absorbs 72044 W at a lagging power factor of pf = 0.67. If the current flowing through the load is Ix = 0.100 A−rms, determine the impedance of the load.
An industrial load consumes 66 kW at a pf of 0.505 lagging from a 480-V rms line. The transmission line resistance from the power company's transformer to the plant is 0.08 Ω. Let us determine the power that must be supplied by the power company (a) under present conditions and(b) thy if the pf is somehow changed to 0.90 lagging. (It is economically advantageous to have a power factor as close to one as possible.
Derive the formula for Average Power, Pavg = VI cosθ watts, where V is the root-mean-square (rms) voltage in volts, I is the root-mean-square (rms) current in ampere, and cosθ is the power factor. For the derivation, use the sinusoidal voltage and current equations. The angle between the voltge and current is angle θ

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Find the average power dissipated in the 200 resistor in the circuit seen in Fig. P10.8 if ig 15 cos 10,000t A. Figure P10.8 = (00:751 isist= 10iA + 2.5 μF 1 mH 7 anto 19vo Ω ano 20 toals dwa isen bellso