Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the the required pumping power input for flow over a 200-feet long section of the pipe. A) 530 Watts B) 461 Watts C) 315 Watts None of the above

Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the the required pumping power input for flow over a 200-feet long section of the pipe. A) 530 Watts B) 461 Watts C) 315 Watts None of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
Water flows through a 4 cm, wrought iron, horizontal pipeline from point A to point B. The pipeline is 50 meters long and contains a fully open gate valve (K=0.15) and two elbows (R/D = 4) (K=0.17). If the pressure at B (downstream) is 192 kPa and the flow rate is 0.006 m3/s, what is the pressure at point A?
A 600mm pipeline, 1550m long is to take water from a reservoir at elevation 150m and discharge it through a 150mm nozzleat elevation 25m. The pipeline is to be constructed so that at a point X, 200m from the nozzle, the pipe shall be 3m below the hydraulic gradeline. What would be the elevation of the pipe at X and what horsepowerwill be available in the jet from the nozzle? Assume f = 0.023 and no loss at entrance to pipe. Use device coefficient = 0.95. Please use figure when solving.
A main pipe distributing water has a diameter of 158 mm and is distributed into three outlets. Thefirst outlet has a velocity rate of 10m/s and a diameter of 50mm. The second outlet has a velocity rate of11m/s and a diameter of 75mm. The third outlet has a flow rate of 0.265619 m^3/s moving at avelocity of 15m/s. if the pressure head in the larger diameter part is 28 ft. a) determine thepressure head at the smaller diameter. b) what is the velocity head of the larger pipe? c) what is the velocityhead of the smaller pipe? d) What is the total head in the system?
Water at four-degree Celsius flows through a pipe that has a conical shape and is sloping downward; has a height difference of 20 meters. The cross section at the bottom is one-half that at the top. If the speed and pressure of water at the top are I m/s and Pa, what is the nressure at the bottom (20 meters below the torn?
A. Assuming sea water to be incompressible with a specific weight of 64.0 lb ft-3. what is the pressure in tons per square foot 2 miles below the surface of the ocean?B. A 40-mm-diameter circular pipe carries water at 20°C. Calculate the largest flow rate for which laminar flow can be expected (in m3 sec-1).
*hydraulics *use handwritten A trapezoidal flume of most efficient proportion has a base of 1.5 m. Its full discharge is 3 m^3/s, If the same material is used for a most efficient rectangular section, Compute the decrease in the discharge. Choices: A. 0.44 m3/s B. 0:54 m3/s C. 0.64 m3/s D. 0.74 m3/s
Water flows down a vertical pipe whose diameter increases suddenly from 175 mm to 350 mm. The discharge in the pipe is 85 lps. The pressure 0.6m above the enlargement section is 275 kPa. Find the pressure at a section 0.6 m below the enlargement section.
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Consider inviscid stagnation flow, ψ =Kxy (see Fig. 8.19b),superimposed with a source at the origin of strength m. Plotthe resulting streamlines in the upper half-plane, using thelength scale a =(m/K)1/2. Give a physical interpretation ofthe flow pattern.
Q3/ The water levels in the two reservoirs A and B are 104.5 m and 100 m respectively above the datum. Pipe joins each to a common point D, where pressure is 98:1 kN/m”*2 gauge at above the joint point D and height is 83-5 m above datum. Another pipe connects D to another tank C. What will be the height of water level in C assuming the same value of ‘f’ for all pipes. Take friction co-efficient f = 0-0075. The diameters of the pipes AD, BD and CD are 300 mm, 450 mm, 600 mm respectively and their lengths are 240 m, 270 m, 300 m respectively. 100 m Your answer
Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.