Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [ 9:57

Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [ 9:57

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the maximum shear stress in the shaft material?
J:41) A motor delivering 3000 kW at 20 Hz to a partially hollow steel shaft (GSt=80 GPa) connected through gearing to an aluminum shaft (GAl=30 GPa) spinning a generator. The maximum shear stress in the aluminum shaft and the total angle of twist from motor to generator is: TmaxAI=6.75MPa, &tot=2.66x10^-3 radians WHY? SHOW WORK! WILL RATE
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the angle of twist of the above stating your answer in degrees?
Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The ultimate tensile strength for the material is 600 MPa and yield stress is 450 MPa. Assume the stress concentration factor = 1.2, surface finish factor = 0.8 and size factor = 0.85.
Please don't copy Find the torque and power transmitted by a 100 mm diameter shaft, if maximum angle of twist and length of shaft are 1.2° and 2 m. Take G = 70 GPa, speed of shaft = 230 r.p.m.
Given: l1=1,3l; l2=1,9l; l3=1,2l; M1=-0,6M; M2=-1,6M; M3=1,9M. Parameter of length l=40cm; cross section diameters: d=41mm; d0=26mm. The shaft is made of steel with yielding shear stress τY=250MPa; factor of safety n=1,6. Find: the allowable value of load parameter (in Nm) MA = ?
A hollow shaft has to transmit 6MW at 150rev / min. The maximum allowable stress is not to exceed 60 MN / m? nor the angle of twist 0.3 ° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN / m?
A rotating hollow shaft is to transmit 30kw at 300rpm, the maximum torque being 20% greater than the mean. The shear stress is not to exceed 60Mpa and twist in a length of 2 meters not to exceed 1.2 degrees. Find the external diameter of the shaft if the external diameter to internal diameter ratio of 2.5. Consider modulus of rigidity as 84 Gpa.
Given: l1=2l; l2=1,2l; l3=1,5l; M1=-1,7M; M2=0M; M3=1,4M. Parameter of length l=40cm; parameter of load М=410Nm. The shaft is made of steel with yielding shear stress τY=190MPa; factor of safety n=1,9. Find: the diameter (in mm) of cross section from strength calculation d = ?
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
A section of a rotating shaft is under an alternating bending moment of 70Nm and a torque of 35Nm. The yield strength of the material is 560 MPa and the ultimate tensile strength of the material is 700 MPa. The estimated actual endurance strength is assumed to be 210 MPa and the stress concentration factor is 1.5 for well rounded fillet. (Design Factor = 2) Determine the minimum diameter of the section of the shaft: D = mm