Find the displacement response of a SDOF system with 20 kg, 30 N.s/m, 5,000 N/m, 0.02 m, 0.5 m/s subjected to an external force with 120 N and 15 rad/s using the regular differential equations solution as well as the convolution integral methods. Plot, compare and interpret the results.

Find the displacement response of a SDOF system with 20 kg, 30 N.s/m, 5,000 N/m, 0.02 m, 0.5 m/s subjected to an external force with 120 N and 15 rad/s using the regular differential equations solution as well as the convolution integral methods. Plot, compare and interpret the results.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A steam power plant is equipped with a condenser that removes 300 MW of heat from steam condensing…

A: Given:Heat removed from the condenser, Q=300 MWTemperature of condensing steam, Tc=30°COverall heat…

Q: Gear 1 has 20 teeth with a diametral pitch of 3.5 TPI. W is the value of the module in inches?

A: Given:Number of teeth, Z=20Diametral pitch, Dp=3.5 TPI

Q: c)Our final figure modeling the forearm is the most realistic so far, showing that the…

A: Solution: Given Data: h2=3 cmd1=3 cmd2=15 cmd3=34 cmh=20 cm To Find: (a) Ratio of Mechanical…

Q: Polysilicon sheet resistance is 50/sq. What is polysilicon thickness?

A: Solution: Given Data: Rs=50 Ω/sq To Find: Polysilicon thickness, t?

Q: Locate the centroid of the plane area shown if a = 2.2in. Round the final answer to two decimal…

A: Given data:- a=2.2 in To find:- Centroid of the plane Centroid ;- it is a geometric center of the…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

Q: An inclined neck. If the p determine the higher than i

A: Givend1=0.075md2=0.019mP1-P2=∆P=175.5 kN/m2Qact=311 dm3/minz2-z1=0.46m

Q: 10 N E D 2.4m 2.4m G C 2.4m B A 2.4 m 2.0m

A: Given: It has a roller support at A and a pin support at B. To find: Which of the following most…

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

Q: Brass-copper alloy class. With the mention of the application of

A: Brass copper alloy Applications

Q: ou drop a golf ball from a height of 1.0 m above the ground. It hits the ground and returns to a…

A: given; You drop a golf ball from a height of 1.0 m above the ground. It hits the ground andreturns…

Q: Wedge Sample Problem The two 20kN blocks are pushed apart by the 15⁰ wedge of negligible weight. The…

Q: The water jet in figure, moving at 15 m/s, is split so that one-third of the water moves toward A.…

Q: Determine the Moment of the area, Q (mm³) about the neutral axis at point A.

Q: Superheated steam at 40 bar absolute and 500°C flows at a rate of 250 kg/min to an adiabatic…

A: Given: P1=40 bar T1=500oC m˙ = 250 kg/min P2=5 bar W˙T,out=1500 KW

Q: Problem 1 Steam enters a turbine operating at steady state with a mass flow rate of 4600 kg/h. The…

Q: Consider the beam shown in (Figure 1). Suppose that w-350 N/m. Figure 1 of 1 Part A Determine the…

Q: There are 2 operators working in this process. Calculate the Cycle Time. 6 Days Process 1 0.5 Days…

A: Write the given data. No. of operators, N=2D1=0.5 daysD2=1 dayD3=1 day

Q: What is meant by the thermal equilibrium diagram of the alloy? And what is its importance?

A: Given Data- Thermal equilibrium diagram topic give we have to discuss it

Q: Problem 1 Water needs to be transferred from one reservoir to another at a rate of 600 gpm. A…

A: Note: As per the policy, we can solve the first three subparts. Please resubmit the remaining parts…

Q: Problem 3: Air initially at t=20°C and pi=1 atm is compressed reversibly and adiabatically to a…

Q: Consider the semiannular area shown. Determine the ratio r₁ to r2 so that the centroid of the area…

Q: www S

A: Given data as per question x=0.1 m m=20 kg F=100 N k=1000 N/m

Q: Q2. A 40 mm diameter jet has a velocity of 25 m/s. Calculate the resultant force on a large flat…

Q: A crossflow heat exchanger uses oil (Cp =2.1 kJ/kg · oC) in the tube bank with an entering…

A: Given:Specific heat of oil, Cp=2.1 kJ/kg.oCInlet temperature of oil, Toil,i=100oCOil flow rate,…

Q: What are the Mechanical Engineering related standards of American Society For Testing and Materials.…

A: ASME Standards: ASME stands for The American Society of Mechanical Engineers . ASME is a wide…

Q: Use the ideal gas equation along with the equation (PVk = C) to derive the following relation: T2 T₁…

A: According to the details provided in we need to find.

Q: Oil(light) enters a heat exchanger at 450 K with a mass flow rate of 10 kg/s and exits at 350 K. A…

A: Givenlight oil To1=450Kmo=10 kg/sTo2=350KTw1=20oCPw=500kPa

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Determine the magnitude of the forces C and T act on the bridge-truss joint. 2 y ΣΕ,

A: Given

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

Q: Calculate the magnitude of the resultant moment (in lb-ft) due to the 200-lb and 50-lb forces about…

Q: 6.28 This planar water jet (60°F) is deflected by a fixed vane. What are the x- and y-components of…

A: To solve this question I have applied the continuity equation and force momentum theorem for the…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

Q: Question 4 Calculate the magnitude of the resultant moment (in lbf-ft) about point A of the…

Q: In the 190.0 meter span cable and a horizontal load of 5.550 KN/m horizontal load, find the location…

A: Given data: L=190.0 mw=5.550 KN/mmaximum allowable stress is 1250 Mpa

Q: A cam drives a flat reciprocating follower in the following manner. During the first 90° rotation of…

Q: Two massless springs, each with a spring constant of k, are used in an experiment. Spring 1 is…

A: Given data:- Spring 1 and Spring 2 with constant K mass of the object =m To find:- magnitude of…

Q: Determine the shear force at point C if P, = 248 |b/ft, P2 = 401 lb/ft, and Pg = 199 lb/ft. ப் P1…

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: Find member FG

Q: 1000 lb 2000 lb 2000 lb F 30° 2000 lb G C 1000 lb 60° H 90 ft 60° 30°

Q: Two carts are positioned on an air track. Cart A has a mass m and has a spring on one end. Cart B…

A: Given: Mass of the car A=m And mass of the car B=2m Initial velocity of car A=v Initial velocity of…

Q: 2. If 100 ft³ of atmospheric air at zero Fahrenheit tempera- ture are compressed to a volume of 1…

A: Given data Atmospheric air volume=100ft3 Intial temperature= 0 degree Fahrenheit Final volume of…

Q: Following are tabulated data that were gathered from a series of Charpy impact tests on a tempered…

A: Given data: To determine:

Q: Determine the force in each member of the truss shown. The load P = answers to their nearest whole…

Q: A plastic bin with a volume of 1 gallon [gal] has a mass of 0.35 kilograms [kg] when empty and is…

Q: 4. Determine the force in each member of the loaded truss shown using methods of joints. B 3 m 4 m F…

Q: Amara's ring box moves 5 meters horizontally when force F = 20N is applied at angle theta = 135…

A: Given Data:- Displacement of the box (x) = 5 m Applied force (F) = 20 N…

Q: 3. A large tank initially contains 200 gal of brine in which 15 lb of salt is dissolved. Starting at…

A: Given data: t=0 tank rate 3.5 gpm initial contain in a tank 200 gal of brine and 15 lb salt…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

K2.

Find the displacement response of a SDOF system with 20 kg,
30 N.s/m, 5,000 N/m, 0.02 m, 0.5 m/s subjected to an external
force with 120 N and 15 rad/s using the regular differential
equations solution as well as the convolution integral methods.
Plot, compare and interpret the results.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the Diameter of a wind turbine rotor which generates 210 kW of electrical power output in a steady wind velocity of 8.5 m/sec with the power coefficient is 63%. The gear, generator and electric efficiencies are 95%, 96% and 89% respectively. Assume the atmospheric air condition is 1.01325 bar, Gas Constant R = 287 J/kg K at 29°C.
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
The static head of a fan is measured to be 160 mm of water gage at an air velocity of 25 m/s. Find the air power at an air condition of 28°C and 98 kPa with a volume flow rate of 5 m3/s.
Q. A single stage impulse rotor has a blade ring diameter of 57.5 cm and rotates at a speed of 10,000 r.p.m. The nozzles are inclined at 20o to the direction of motion of the blades and the velocity of the issuing steam is 1,050 m/sec. Determine the inlet blade angle. Assume a friction coefficient of the blading equal to 0.85 and that the inlet and outlet angles are equal. Find also: (a) the power developed at the blades for a steam supply of 1,350 kg per hour (b) the diagram efficiency, and (c) the loss of kinetic energy due to blade friction
For a system with mass 10 kg, spring constant 100 N/m, damping ratio 1 kg/s, rotating unbalance of 0.1 kg, radius 100 cm, and driving frequency 50 Hz, what is the amplitude of the particular solution? What is the phase lag of the particular solution?
A spring mass system having spring stiffness is 45 N/m and mass 20 kg. What is the natural frequency associated with this system?
A fan delivers 4.804 m^3/sec at a static pressure of 5.245 cm of water when operating at a speed of 511.31 rpm. The power input required is 3.515 kW. If 9.103 m^3/s are desired in the same fan and installation, find the pressure in cm of water Answer in whole number
a. Given the static head of 28.91 m, and static pressure head of 3.15 cm WC. What is the normal pressure, Pn? b. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. c. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.
A 70mm vane axial fan is running at 2000rpm delivers 7.5 cubic meter/sec of air against static pressure of 8cm water with input power of 12kW. If the fan wheel diameter is increased with the new power input of 18.1 kW, determine: a. the new diameter of the fan in mm 67 74 76 b. the new static head in meter of water 8.4 9.4 10.4 c. the new discharge in cubic meter/sec 8.598 9.198 9.598
engineering vibration question. Find the natural frequency of the spring-mass system when m = 1 kg, k = 3 N/m, Xo = -1 mm, and Vo = -1 mm/s, and plot the response for at least 2 cycles. how can i solve it?? Please attempt If you are 100% Sure ,Or else Skip.
Through a duct air enters a fan at 6.3 m/s and an inlet static pressure 2.5 cm of water less than atmospheric pressure. The air leaves the fan through a duct at 11.25 m/s and a discharge static pressure of 7.62 cm of water above the atmospheric pressure. If the specific weight of the air is 1.2 kg/cubic meters and the fan delivers 9.45 cubic meters/sec, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling
2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?