Find the gage block for 86.305 mm dimension.

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Solve for the x-component (in mm) of the centroid if that a=2.1, b=2.2, c=4.2, d=9,4, and r=1.2. All…

A:

Q: Determine the resultant mom ent 6+be fig. show n below:

A: Given data Forces acting are 800 N, 200 N

Q: Solve for the x-component (in mm) of the centroid if that a=2.2, b=2.3, c=4.7, d=9.5, and r=1.6. All…

A:

Q: For the given Three views, Draw the Isometric Body, using scale 1:1, all dimension are in…

A:

Q: Find (ly) for the shaded area

A:

Q: r. Find the dimensions of th

A:

Q: Compute Ix (I sub x, in inches4, round-off to 2 decimal places) for the region shown.

A:

Q: Solve for the x-component (in mm) of the centroid if that a=2.2, b=2.3, c=4.7, d=9.5, and r=1.6. All…

A:

Q: Solve for the y-component (in mm) of the centroid if that a=2.3, b=2.4, c=4.8, d=8.7, and r=1.5. All…

A:

Q: . Find the width c will

A: Need to find width of rectangular duct.

Q: Solve for the y-component (in mm) of the centroid if that a=2.4, b=2.3, c=4.7, d=9.8, and r=1.4. All…

A:

Q: For the Gage shown find the distance when 20=22.

A: To Find the distance x

Q: Determine the maximum diameter of a ball floating on water at 20°C if it has a density of 5060…

A: It is required to determine max diameter of ball

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Compute ly (I bar sub x, in inches“, round-off to 2 decimal places) for the region shown. .4

A:

Q: For the H- section shown, Find the value of h so that I = ly. 20mm 100mm | 20mm h = ? 20mm 140mm

A: Draw the given H-section. Since the given H-section is symmetric, the centroid will lie in the…

Q: Figure below shows a composite shape on a positive x-y coordinate system (solve the question by…

A: .

Q: Compute Ix (I bar sub x, in mm*, round-off to 2 decimal places) for the region shown. -30 15 12.5 45…

A: Given data: - The width of the lower section is b3 = 40 mm. The height of the lower section is h3 =…

Q: From the figure given above, compute the value ofR so that the curve will pass through a point which…

A: First make a FBD of the diagram as shown below,

Q: determine the diameter o

A: Given data; A shaft is supported on two bearings as shown in figure:length =1.5 mIf shaft is…

Q: Determine the diameter for the cylindrical cup

A: Given data; Neglecting the variation in the sheet thickness;  Determine the diameter ? Where,  10 mm…

Q: Find the area of the following shape using the information provided.

A: Given Shape To find Area of the shape

Q: Solve for the y-component (in mm) of the centroid if that a=2.2, b=2.2, c=5, d=9.7, and r=1.7. All…

A:

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: Find the cross sectional dimensions of the smallest square bea

A: To find cross sectional dimensions of the smallest square beam

Q: y 19 39 54 39- 39 54 Dimensions in millimeters

A: GIVEN DATA - Equilateral triangle having one hole we have to find centroid of area

Q: : diameter and 6 m lor riction. [Take density

A:

Q: Determine the dimensions of the riser

A: Given: Diameter of casting mold = 12 cm r=6 cm Length=h= 20 cm Solidification time of casting = 0.9…

Q: C0nsider the figure bel0w where each square is 1 ft on a side and A =58lb, B =58lb, and C =182lb.…

A:

Q: Solve for the tensions 45 50 g

A: Given: W=50 g Consider the Free Body Diagram:

Q: Given the mass of a material to be 100 grams and a density of 4g/cc, compute the sphericity if the…

A:

Q: Compute Ix (I sub x, in inches", round-off to 2 decimal places) for the region shown. - 6 in. 6 in.-…

A:

Q: If gage A reads -20 kPa, determine the elevations of points L, N, Q and D.

A:

Q: Draw a common tangent to two circles of diameter 6cm and 4cm respectively if the distance between…

A:

Q: DISSO a) Determine the decrease in its length b) Determine its new diameter.

A: for solution refer below images.

Q: Solve for the areain two different ways. 12

A:

Q: Solve for the x-component (in mm) of the centroid if that a=2.2, b=2.3, c=5, d=9.3, and r=1.4. All…

A: Answer:  X-bar = 127.653 mmFor a step-by-step solution have a look through the attached pictures of…

Q: The y of the area

A: Given: To determine: The of the area

Q: Find the centrid of the area bounded by the given aerr, and

A: The centroid of an area can be considered as its geometric center. The coordinate of the centroid is…

Q: SOLVE THE FOLLOWING PROB LEMS:

A:

Q: Find the centroid of given figure. All dimensions are in mm. 150 200 200 200 300

A: Given data as per question Radius of the hole =200 mm Calculations Considering section 1A1=175000…

Q: If gage A reads -20 kpa, determine the elevations of points L, N, Q and Z.

A:

Q: Compute Ix (I bar sub x, in inches“, round-off to 2 decimal places) for the region shown. Dimensions…

A:

Q: Solve for the y-component (in mm) of the centroid if that a=2.3, b=2.3, c=4.9, d=9.1, and r=1.4. All…

A:

Q: If the block is loaded with P = 257 kN, calculate the required dimension "h" of the key. Write your…

A:

Q: determine the radius of the fillets

A: Given: P=10 kN Breadth of the plate, D= 96 mm Diameter of the hole, d'= 9 mm Thickness of the…

Q: Solve the mobility of the following figures, show complete solutions.

A:

Q: The neutral axis of the given built up section is nearest to ______ measured from the bottom of the…

A: Given data,  All the dimensions of W14x30 is given in the figure,  And  Neutral axis is the axis of…