(a) Which component of the horizontal axis wind turbine can be considered as the brain of the system? Write the important functions of this component. Explain how it coordinates with the anemometer, wind vane and yaw drive for the proper working of turbine. (b) Explain, why wind energy is considered as highly desirable and economical to the rural areas which are far from existing grids.

(a) Which component of the horizontal axis wind turbine can be considered as the brain of the system? Write the important functions of this component. Explain how it coordinates with the anemometer, wind vane and yaw drive for the proper working of turbine. (b) Explain, why wind energy is considered as highly desirable and economical to the rural areas which are far from existing grids.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider two identical wind turbines with a hub height of 40 m, one located in flat agricultural land and one located above a forest. What is the relative output power for the two turbines if the wind velocity is 10 m/s at a height of 100 m in both cases? Pagricultural/Pforest = ?
The runner in a turbine is 70 cm in diameter. The wheel develops 410 kW when turning at 600 rpm under a head of 43 m. What is the specific speed of the turbine? Answer : 28.9 please Explain carefuly
Explain in detail the positioning and environmental impact of large wind turbines
A backward-swept centrifugal fan develops a pressure of 80 mm of water gauge. It has an impeller diameter of 0.89 m and runs at 720 rpm. The blade angle at the tip is 39° and the width of the impeller is 0.1m. Assuming a constant radial velocity of 9.15 m/s and density of air as 1.2 kg/ m3 , determine the fan efficiency, discharge and power required.
Discuss which dimensionless pump performance parameter is typically used as the independent parameter. Repeat for turbines instead of pumps. Explain.
How long should a rotor blade of a wind turbine be if it is designed to produce 10 kW and the prevailing wind speed is about 50 kph? Assume that air density is 1.20 kg/m3.
Estimate the amount of power generated by a wind turbine having a powercoefficient of 0.37 given the annual average wind speed:Rotor diameter = 125 mCenter of rotor at an elevation 160 m above the surface level.Location: Oklahoma City, OK
Consider Fig. P3.36 as a general problem for analysis of amixing ejector pump. If all conditions ( p , ρ , V ) are knownat sections 1 and 2 and if the wall friction is negligible,derive formulas for estimating ( a ) V 3 and ( b ) p 3 .
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
Figure shows two points a half-period apart in theoperation of a pump. What type of pump is this ? Howdoes it work? Sketch your best guess of flow rate versustime for a few cycles.
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m. The runner blade angles are ?2 = 71.4° and ?1 = 15.3° at the turbine inlet and outlet, respectively. The runner rotates at n. = 160 rpm. The volume flow rate at design conditions is 80.0 m3/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (MW) and required net head (m).