Find the Global Stiffness Matrix and node displacements for the following BAR structure  where A = 3 x 10-4 m2 and E = 210 GP

Q: For the beam and loading shown, calculate the value of the slope and deflection of the NA at…

A: The values are  wo=5.2 kips/ftMo=2185.3 kip.ftL=20.5 ftE=29*106 psi The beam is W21×101

Q: 3. A truck drives off a cliff with horizontal velocity of 8 m/s. The cliff is 138 m high. How much…

A:

Q: Prob. # 6] Determine the maximum and minimum normal stresses of the lever shown in figure P6. Fixed…

A: Principal stresses are the maximum or minimum value of normal stresses and they act on those plane…

Q: Determine the magnitude of the pin force at A. Assume W = 555 lb, a = 3.8 ft, b = 2.9 ft, r = 8 in.…

A: W=555lb r=8 in a=3.8ft b=2.9ft

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Q1) Air is to be expanded to Mach number (2.0) in a convergent-divergent nozzle from an inlet…

A:

Q: a) How can we test which can withstandthe most stress, a length of spider web thread or a steel wire…

A: Formula used: Write the expression for the stress. σ=E×ε Here, σ is stress, E is plastic modulus and…

Q: WORKSHEET: A racing car starts at rest at point A and increases its speed around the track at a…

A:

Q: We can make assumptions for the unknown value to to be able to find these: Length of swing arm is…

A: Given: Length of swing arm = 19 in Length of sling = 10.5 in To find: A)position vectors for…

Q: Determine the radius of gyration of the aluminum part about the z-axis. The hole in the upper…

A: Given: To find: Radius of gyration about z axis

Q: Problem 2: Neatly draw the shear and moment diagram for the beam shown below using the method of…

A:

Q: For the solid shaft, 1 inch in diameter, subjected to bending and torsion, find the principal…

A:

Q: The m = 6.5kg glider is released from rest at A and slides with negligible friction along circular…

A: Write the given data with variables. m=6.5 kgh=R=0.6 m   It is required to determine the velocity of…

Q: The assembly consisting of a uniform slender bar (mass= 1.5 kg and L=0.49 m) and a rigidly attached…

A: The initial angular acceleration. Given: The mass of the slender bar is mb=1.5 kg. The length of the…

Q: If point C is the center of bar BD, why is CD measured as 24in and not sqrt(24^2 + 10^2)/2 or 24/2?…

A: We know that, motion of any link in a mechanism is general motion i.e. combination of rotation and…

Q: The suitability of a strain gauge data logger.

A: Given data:- strain gauge data logger To be explained:-The suitability of a strain gauge data…

Q: A long cable of length L = 44 m and mass p = 0.100 kg/m is wrapped around the periphery of a spool…

A: given: ρ = 0.1 kg/m L = 44 m r = 44 m

Q: Question 2 The water in a tank is pressurized by air and the pressure is measured by a multifluid…

A: The water in a tank is pressurized by air and the pressure is measured by a multifluid manometer as…

Q: The three T's of combustion are commonly referre1 d to as a. time, temperature, and type of fuel…

A: Combustion : Is the reaction in which oxygen reacts with substance leads to release energy in the…

Q: Problem #5 A 100-mm-wide by 8-mm-thick steel bar is transmitting an axial tensile load of 3,000 N.…

A:

Q: Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate…

A:

Q: 15.160 At the instant shown the length of the boom AB is being de- creased at the constant rate of…

A:

Q: (i) Determine the state of stress at point B on the cross-section of the post at section a-a. (ii)…

A:

Q: Prob. 19-9 19-10. The frame of the roller has a mass of 5.5 Mg and a center of mass at G. The roller…

A: The mass of the frame is 5.5 Mg=5500 kg The mass of the roller is 2 Mg=2000 kg The radius of…

Q: Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.15 L/min. The velocity (m/s)…

A: we got  d=0.009m Q=2.9167×10^-5 m^3/sec

Q: The slider block has the motion shown. Suppose that r = 130 mm and h = 550 mm. (Eigure 1) Figure B…

A:

Q: Two 38.1 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts SAE 1020…

A: flanged coupling d=38.1mmn=6D=152.4mmN=260 rpmT=850000 Nm  =850000 ×103 Nmmfs=5Sult=430MPaSsy=330…

Q: 2 60° 60⁰ 100 KN 60⁰ 3

A:

Q: For the system shown below. a) Derive the equation of motion b) Find the natural frequency of this…

A: Free body diagram shown below: Formula used: The standard equation of motion for spring mass system…

Q: what's the formula for axial force? can you cite some reference because I can't see that formula on…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Draw Mohr’s circle that describes each of the following states of stress for diagram a, b, c.

A:

Q: a. Air lows past an object and exits as a free jet as shown in the figure. Because of the…

A: Given Data: Ve=4 m/s       for 0≤r≤0.5 mVe=12 m/s     for 0.5 m≤r≤1 mVavg=10 m/s   To Find: Momentum…

Q: Determine the distance (in m) that the load W is raised in 7.1 seconds, when the system shown in the…

A:

Q: bob and Hano meet up to fly a toy helicopter. At full power, the airplane can fly 100 km per hour in…

A: Given data is

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

Q: Given a front hand brake of a bicycle. The applied force, P = 70 N and the equivalent area and…

A:

Q: If the heat exchanger is characterised by uniform overall heat transfer coefficient, using the LMTD…

A:

Q: The attached wheels roll without slipping on the plates A and B, which are moving in opposite…

A:

Q: An airfoil shape is shown below. The vectors for the force of the fluid on the airfoil are positive…

A: Airfoil is the basic form of wings. These are curved surfaces. It is used to obtain the helpful…

Q: Water flows steadily with a velocity of 4m/s in a horizontal pipe having a diameter of 16.24cm. At…

A:

Q: Learning Goal: To use the conservation of linear momentum to determine the final state of a group of…

A: VA = 3.5 m/s VB = 1.7 m/s VC = 2.3 m/s mA = 1.9 kg mB = 2 kg mC = 3.6 kg Required: V ( final…

Q: The two 4.6° wedges shown are used to adjust the position of the column under a vertical load F of…

A: According to the given data Wedge angle =4.6deg F=4.2kN μ=0.28 We need to find Force P

Q: Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600…

A: Given Data  Mass flow rate= 2000 kg/h Q=111600 kJ/h T₀ =95°C C=3.9 kJ/kg.K

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: According to the given data R=20 N.m F=150N  We need to find Normal stress at cross-section point-A

Q: Use Castigliano's theorem to determine the magnitude of deflection at midspan for the solid steel…

A: The dimensions are a=3 in, b=7 in, da=1.125 in, db=1.875 in The distributed load is w=160 lb/in

Q: Laminar flow normally persists on a smooth flat plate until a critical Reynolds number value is…

A: Given that, Local heat transfer coefficient for laminar flow, hx, Laminar = (1.74W/m11.5.k)x-0.5…

Q: Question 2: In an offset slider-crank mechanism the crank am coupler 13 = 100 mm; and the offset 0 =…

A: The crank length, r=40 mm The coupler length, L=100 mm The offset: a=25 mm

Q: Some homes that use baseboard heating use copper tubing. Hot water runs through and heats the copper…

A: Mass of the copper tube,(m)=540 g. Initial temperature,(T1)=15.01oC Final temperature,(T2)=25.48oC…

Q: Part B - Zero-force members in a loaded truss Consider the loaded truss shown below. Identify the…

A: This question is based on the concept of Truss.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.