From the circuit shown below calculate the following+ Vc -C=0.05pf10VR1=100kR2=100ka) Find the mathematical expression for the voltage across the capacitor from the previous figure, if the switch is set to position1 at t=0s.Calculate the voltage vc in t=10ms.Repeat the previous for ic and VR,-b) Find the mathematical expression for the voltages vc and VR, and the currentiç if the switch is set to position 2 at t=30ms(Assume that the leakage resistance across capacitor =c0ohms)c) Find the mathematical expression for the voltages ve and (VR, + VR2) and forthe current ic, if the switch is set to position 3 at t=48 ms.Find the voltages vc and VR + VR2 and the current iC at t = 100ms.d) Plot the waveforms obtained in the previous on the same time axis for each voltage and forcurrent.

a) Switch is set at position 1 at t=0sec. This forms a simple series RC circuitR=100KΩC=0.05pFTime…

Find the mathematical expression for the voltage across the capacitor from the previous figure, if the switch is set to position 1 at t=0s. Calculate the voltage vc in t=10ms. Repeat the previous for ic and VR,- Find the mathematical expression for the voltages vc and VR, and the current ie if the switch is set to position 2 at t=30ms (Assume that the leakage resistance across capacitor =o0ohms) Find the mathematical expression for the voltages Ve and (VR, + VR2) and for the current ic, if the switch is set to position 3 at t=48 ms. Find the voltages vc and VR, + VR2 and the current iC at t = 100ms. Plot the waveforms obtained in the previous on the same time axis for each voltage and for current.

Find the mathematical expression for the voltage across the capacitor from the previous figure, if the switch is set to position 1 at t=0s. Calculate the voltage vc in t=10ms. Repeat the previous for ic and VR,- Find the mathematical expression for the voltages vc and VR, and the current ie if the switch is set to position 2 at t=30ms (Assume that the leakage resistance across capacitor =o0ohms) Find the mathematical expression for the voltages Ve and (VR, + VR2) and for the current ic, if the switch is set to position 3 at t=48 ms. Find the voltages vc and VR, + VR2 and the current iC at t = 100ms. Plot the waveforms obtained in the previous on the same time axis for each voltage and for current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is a Linear Circuit? Simply we can say that the linear circuit is an electric circuit (Links to an external site.) and the parameters of this circuit are resistance, capacitance, inductance and etc are constant. Or we can say the parameters of the circuits are not changed with respect to the voltage and current is called the linear circuit. What is a Non-Linear Circuit? The non-linear circuit is also an electric circuit and the parameters of this circuit differ with respect to the current and the voltage. Or in the electric circuit, the parameters like waveforms, resistance, inductance and etc are not constant is called as Non- linear circuit. Question: Is it possible to apply superposition theorem to nonlinear circuit? If yes, why? and if no, why?
An 8 μF capacitor is a 200 V DC in series with a 0.5 MΩ resistorlinked to the source. According to this;a) τ =?b) Initial value of charging currentc) The time required for the voltage at the capacitor ends to become 160 V.d) 4 s after connecting to the source, i =? and Vc =? Calculate the values.
For the circuit shown in the figure, in which the capacitor is initially fully discharged. If the source voltage V is 17 Volts, the capacitance of capacitor C is 24 mF; and the values of the resistors in Ω are: R1 = 2250 , R2 = 1071 , R3 = 2455 , R4 = 1199 and R5 = 1043 Determine the voltage across the capacitor in Volts after 15 minutes have elapsed since the circuit is energized. ..
16. Consider a simple RC circuit which has a resistor of 2 ohm and capacitor of 3F. If the initial voltage is 12V then find the charge q(t) is expression. 17. Suppose we have a RC circuit with an alternating voltage V(t) = V_{m} * cos(5t) If the initial voltage is 4V and the resistor has a resistance of 8 ohm and the capacitor is of capacitance 2F then find the charge for the circuit ?
You measure the capacitanceC1of a capacitor by doing thefollowing: First connect capacitorsC1andC2in series to a power sup-ply that provides a voltageVthat can be varied. The capacitance ofC2is known to be3.00mF. Then vary the applied voltageV, and for eachvalue ofVmeasure the voltageV2acrossC2. After plotting your data asV2versusV, you find that the data fall close to a straight line that hasslope 0.650. What is the capacitanceC1?
An RC circuit includes a basic switch. In position "a", the battery, resistor and capacitor are connected in series, and the capacitor charges. In position "b", the battery is replaced with a short, and the capacitor will discharge. Two voltmeters and an ammeter have been added to the circuit. A) Enter an expression for the charge as a function of time. B) What is the maximum value of the current after the switch is closed? C) Enter an expression for the current as a function of time. Your answer must explicitly reference the maximum current, Imax, that was determined in the previous step. D) Enter an expression for the voltage measured across the resistor, VR, as a function of time. E) Enter an expression for the voltage measured across the capacitor, VC, as a function of time. F) Add an expression for the sum of the voltages across the resistor and the capacitor as a function of time, VR + VC
A circuit consists of switches that open or close at t=0, resistances, dc sources, and a single energy storage element, either an inductance or a capacitance. We wish to solve for a current or a voltage x(t) as a function of time for t≥0. Write the general form for the solution. How is each unknown in the solution determined?
Suppose that at t=0, we connect an uncharged 10{μF capacitor to a charging circuitconsisting of a 2500-V voltage source in series with a 2{MΩ resistance. At t=40s, the capacitoris disconnected from the charging circuit and connected in parallel with a 5{MΩ resistor.Determine the voltage across the capacitor at t=40 s and at t=100 s. (Hint: You may find itconvenient to redefine the time variable to be t′=t−40 for the discharge interval so that thedischarge starts at t′=0.)
An RC circuit has an emf of 100 volts, a resistance of 5 ohms, a capacitance of 0.02 farad, and an initial charge on the capacitor of 5 coulombs. Find (a) an expression for the charge on the capacitor at any time t and (b) the current in the circuit at any time t.
In the circuit shown in Figure 1, find the values of R and C such that the steady-state voltage across the capacitance and the time constant of the response for t> 0 are -10V and 20 seconds respectively. Place all the details of your design.
For the circuit in the figure, initially the switch S is closed in (b), until the capacitor is charged; then the switch goes to point (a) so that the battery is disconnected and the capacitor, resistor and inductor are connected in series. Once S is connected at point (a), find a) the angular frequency of oscillation for the series circuit b) write the equation for the charge on the capacitor as a function of time with the respective values of Qmax, angular frequency Wd and time T c) make the Q(t) graph showing explicitly the envelope of the exponential decay (Hint: use geogebra or an application of your choice to obtain a graph).
For the following circuit, do the following:a) Write the mathematical expressions for the voltage VC, VR1 and IC if the switch is on theposition 1.b) Find the voltage VC, VR1 and IC if the switch changes to a position 2 at t = 100ms.c) Determine the discharge time of the capacitor.d) Draw the charge and discharge waveforms.