Question 7The charge entering the positive terminal of an element isq = 5 sin 4nt mCwhile the voltage across the element (plus to minus) isv = 3 cos 4nt VFind the power delivered to the element at t = 0.1 s. Express your answer in mW and round to two (2) decimal places.

Answered: Image /qna-images/answer/3c17300e-0805-42fb-800f-e21245f010b2.jpg

Answered: Find the power delivered to the element…

Engineering

Electrical Engineering

Find the power delivered to the element at t = 0.1 s. Express your answer in mW and round to two (2) decimal place %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q3) For a 20 A, 230 V energymeter, the number of revolutions per kWh is 480. on test at full load,…

A: In this question we will find error in energy meter reading and will also find that meter is running…

Q: A cell has emf 1.54 V when it is in series with 10 resistance; the reading of the voltmeter…

A: When no current in thee circuit the value of emf and terminal voltage are equal. The emf value…

Q: Determine the currentį in the circuit below. 2 cos 101 V 1F = 1 H ll

Q: Three light bulbs L1 = 18 W, L 2= 7 W, L 3= 29 W, are connected to a 14 V battery as shown in Figure…

Q: 1000 Ω www R ig ( ↑ 160 nF 100 mH For the circuit shown above, what is the average power supplied by…

A: Here we do calculations for the given single phase AC circuit.

Q: 1000 Ω W R m ig 160 nF 100 mH ?For the circuit shown above, what is the average power supplied by…

Q: The charge entering a certain element is shown below. Find the current at t = 12 ms. | = Blank 1 A…

A: We need to find out current for given charge distribution

Q: Find i in the circuit v voltage Vs = 50 cos 200

Q: 2) The voltage across an element and the current through it are given by : v(t) = 4t3 + 2t2 +1 V %3D…

A: Current through the above resistor is given by :- i(t) = ddt(4t3+2t2+1) = (12t2+4t) mA This is…

Q: The charge flowing in a circuit element is plotted in the following figure. The plot for current…

A: Resistance opposes the flow of current. By ohm's Law resistance is given as R=VI Current is rate of…

Q: • The power absorbed by the 10-kN resistor in the following circuit is 3.6 mW. Determine the voltage…

Q: Determine the current in the loop of 12ohms, 0.1vx, 12 ohms. (Express your answer in milli (103))

Q: zero O b. 202 Oc. 52 If a simple wire is connected across the two terminals of a resistance, the…

Q: Find the power delivered to the element in Example 1.5 at t = 5 ms if the current remains the same…

A: sol: (a) consider the current in an element is i =5cos60πtA. consider the voltage across the…

Q: 4. The charge entering a certain element is shown below. Find the current at (a) t = 1 sec and (b) t…

A: From the current definition

Q: 2) The voltage across an element and the current through it are given by : v(t) = 4t3+ 2t2 +1V…

A: From the basics of network

Q: 2. Explain the difference of power and energy.

A: IMPORTANCE OF OHMS LAW: Ohm’s law is vitally necessary to describing electrical circuits as a…

Q: Q3) The meter constant of 5A, 220 V, d.c. watt-hour meter is 3275 revolutions per kwh. In a test run…

Q: The current shown here is applied to a 10H inductor. Calculate the power at 2.5 seconds. Express…

A: Consider slope between 2 sec and 3 sec ,because we need to calculate the power at time instant…

Q: 14.) Find the value of power dissipated if a voltage v = 240 sin (30t + Tt/4) is applied to a…

A: Power dissipation in a resistor: The power dissipates in the resister in the form the heat and the…

Q: Find power dissipated in all elements 120 v. ww ww 60 V 122 24 V

A: Since you have asked multiple questions and not specified which one to answer I will answer the…

Q: The current shown here is applied to a 7 H inductor. Calculate the power at 2.5 seconds. Express…

Q: Q3) For a 20 A, 230 V energymeter, the number of revolutions per kWh is 480. If on test at full…

A: In this question energy meter is given...We have to find out error in measurement of energy....Also…

Q: 36. A stove element draws 15 A when connected to 230 V line. How long does it take to consume one…

A: we need to find out time t.

Q: Find the power delivered to a resistor at t=3 ms if the current entering the resistor is i=5 cos…

A: Power delivered to a resistor can be defined as the product of the current flowing through the…

Q: 14.) Find the value of power dissipated if a voltage v = 240 sin (30t + Tt/4) is applied to a…

Q: Find i in the circuit when the source voltage Vs = 50 cos 200t volts. %3D

Q: If wind was blowing 10 m/s, what is the max. power that can be generated from the wind hitting the…

A: Given: Speed of wind, v=10 m/s Blade length, r=30 m Assume turbine at sea level.

Q: Conservation of energy requires that the sum of the power absorbed by all of the elements in a…

Q: 1.31 The current waveform as shown below, is applied in a pure resistor of 10 2. What is the power…

A: Given current waveform,

Q: 15.) Find the value of power dissipated in a 43-ohm resistor if the applied voltage is v = 250 sin…

Q: 2) The voltage across an element and the current through it are given by: v(t) = 4t3+ 2t2 +1V %3D…

A: The expression for current and voltage across an element is given. v(t)=4t3+2t2+1 Vi(t) = 24t2 + 8t…

Q: An industrial load is known to be inductive and consumes 90 KW. The ammeter reading is 260 A ms, and…

A: Given: V=480 v I=260A P=90kw

Q: The following equations describe an electric circuit: -I, (220 N) + 5.80 V – I, (370 N) = 0 +I, (370…

A: Given equations, -220I1+5.8-370I2=0370I2+150I3-3.1=0I1+I3-I2=0 By rearranging,…

Q: 12 v (V), 12 - 8 12 16 20 t (ks) i (A) 24 16 8- 12 16 20 t (ks) The voltage and current at the…

A: Given graph for voltage an current:

Q: In a hot wire ammeter the current flowing through the resistance of 10 Q is given by 1 = 3 + 2 sin…

A: Given equation, I=3+2 sin 300t A

Q: 3. If the current flowing through an element is given by 3t A, 0<t<6 s 16A, 6<t < 10 s -12A, 10 <t<…

A: The solution is given below

Q: 10 n 12 V Answer the following questions when V1 = 8 volt The mesh current I, = Amp Power supplied…

A: We need to find out current and power for given circuit

Q: if the power consumption is 1200 kwh the DC power in kw, is: Use pv module with 300w power output,…

A: if the power consumption is 1200Kwh the DC power in Kwp is: use PV module with 300w power output and…

Q: 8 v (V) 12 8 4 4 8 12 16 1 (ks) i (A) 24 16 8 4 12 16 20 t (ks) The voltage and current at the…

A: We know area under the power (VI) curve is the total energy transferred.

Q: Samson washes his long dark locks every day. He spends half an hour each day drying his hair with an…

A: The consumer uses the dryer for 0.5 hr per day. In a week the number of hours the dryer is used is…

Q: Which of the following is the CORRECT formula fo 19. X = 2TL X = 2nfL X = 2nf X = nfL a. %3D b. %3D…

A: The inductive reactance is the reactance offered by the coil to the flow of current. The inductive…

Q: Q4: The figure shows the power consumption of a certain household in 1 day. Calculate: a) the total…

Q: Problem 3 A water jet consumes "3X50"W for 126 hours a week. What is the energy consumed (kWh) for a…

Q: 3. If the current flowing through an element is given by 3t A, 0<ts 6 s 16A, 6<t< 10 s -12A, 10 <t <…

A: Given, The current flowing through an element is given by, it=3t A, 0≤t≤6 s16 A,…

Q: Find the power delivered to an element at t=2 s if the current entering its positive terminal is…

A: Given, i(t)=2cosπtv(t)=12i(t)t=2 s

Q: f you exert 2 N for a distance of 1 meter, in 3 sec, you will deliver a power of a. 1/3 W b. 2/3 W…

A: Given data, Force is given F = 2 N Distance is given d = 1 m Time is given t = 3 sec

Q: HW 1: How much current, i, is drawn by an electrical device with resistance 15 N at 110 V?

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: 1000 Ω ig R www O 160 nF 100 mH For the circuit shown above, what is the average power supplied by…

A: Given data : ig=7cos5000t A Given circuit can be redraw :

Q: Compute the power absorbed or supplied by each component of the circuit. Prove your answer using the…

Concept explainers

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1) The charge entering the positive terminal of an element is q = 5 sin 4πt, mC while the voltage across the element (plus to minus) is v = 3 cos 4πt, V. a. Find the power delivered to the element at s. b. Calculate the energy delivered to the element between 0 and 0.6 s
The charge entering the positive terminal of an element is q = 6 sin(4πt) mC, while the voltage across the element (plus to minus) is v = 6 cos(4πt) V. Calculate the energy delivered to the element between 0 and 0.6 s. in mJ
SITUATION NO. 1 - A specific circuit element has a charge of q = 10e^(2t ) coulomb and a voltage across it of v = 10e^(-t) volts. (Note : t is time in seconds) 1. Find the current that passes through the given circuit element at t = 1 second * 137.78 A 147.78 A 157.78 A 167. 78 A 2. Find the power dissipated in the circuit element at t = 1 second. * 271.83 W 281.83 W 291.83 W 301.83 W 3. Find the energy absorbed by the circuit element from t = 0 to t = 1 second * 171.83 J 181.83 J 191.83 J 201.83 J
1.8 The power delivered to an element is p = 12 sin 4t W and the voltage is v = 4 sin 2t V. Find the current entering the positive terminal and the charge delivered to the element between 0 and π/4 sec.
A voltage of v(t) = 2 cos(2π 49 t) volts is applied across the 48-ohm resistor. Find the total charge, in microcoulombs, traveling through the resistor in a duration of 2.49 seconds if the initial charge in the resistor is 9 microcoulombs.
Ohm's law describes the relation of energy and power dissipated by an element. Select one: True False
A copper wire has a diameter 5mm and length 8 cm with a conductivity 5x107 S/m. If an electric field of 3 mV/m is applied between end points what is the value of power density in the wire ? Lütfen birini seçin: a. 350 J/m3 b. 450 J/m3 c. 500 J/m3 d. 300 J/m3 e. 400 J/m3
A small glass bead has been charged to + 60.0 nC . A small metal ball bearing 1.40 cmcm above the bead feels a 1.90×10−2 N downward electric force. What is the charge on the ball bearing? Express your answer with the appropriate units.
The current entering the upper terminal is i=24 cos 4000t A Assume the charge at the upper terminal is zero at the instant the currentis passing through its maximum value. Find the expression for q(t).
Use the following values: ZR=8 Ohms ZL=30j Ohms Write the final answer to at least 5 significant figures.
A copper conductor wire with a total length of 100ft is used in a 15 amp common household circuit has a resistance of 1.62 ohms/1000ft. If the circuit is fully loaded, determine the heat produced by the conductor? (Hint 1W = 3.413Btu/hr) a. 124.40 Btu/hr b. 99.83 Btu/hr c. 8.29 Btu/hr d. 177.50 Btu/hr
A certain electrical element draws the current i(t) = 119 cos 4t A at avoltage v(t) = 119 cos 4t V. Find the energy absorbed by the element in2 s. Put an illustration figute with compelte solutions, step by step, kindly handwritten it. THank you!