find the reaction at both support
Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 80%, and a volume of…
A:
Q: Define aur vessels. Explain the advantages of air vessel in pump system.
A: Air vessels are used in the reciprocating pump. It is basically a cast iron closed chamber having an…
Q: Inside a piston cylinder is 1 kg of pure water at 25°C. The piston is 15 cm in diameter and has a…
A:
Q: explain the energy transfers and stores in heating gloves
A: given; explain the energy transfer and stores in heating gloves
Q: (3) A cylinder with a cross section S with a frictionless piston with a mass of M is fixed at the…
A: Draw the above given diagram.
Q: A full depth gear tooth of 20° pressure angle has standard addendum. Dedendum is 1.25 times of…
A: As given in question, Pressure angle = φ = 20o Module = m = 2.5 mm Addendum = a = m = 2.5 mm (For…
Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…
A: Given:nA=0.3CA=120nB=0.5CB=30
Q: QUESTION 4: NATURAL CONVECTION Two concentric spheres with diameters D₁ = 60 mm and Do = 100 mm are…
A: The process of transfer of heat which happens due to the movement of the fluid particles by means of…
Q: A 10-kg mass is attached to a spring, stretching it 0.7 m from its natural length. The mass is…
A:
Q: rate shown below, determine the principal strains Exy -Exx Eyx Eyy Eyz E Ex Egy EN -1.1 0.5 0.5 2.4…
A: solution of above problem is below:
Q: Each of the blocks shown in figure (9.14) he The rear block moves with a speed of 2 m/= Front block…
A:
Q: A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter…
A:
Q: OBD II systems use several modes of operation. List three of them.
A: There are nine Global OBDII modes. Three of them are Monitor Status and Current Data, Freeze Frame,…
Q: The 200 x 200 x 1.250-mm oak (E-12 GPa) block (2) shown is reinforced by bolting two 5x 200 x 1.250…
A:
Q: A SAE 1040 cold rolled shaft have a yield point of 70 ksi, a diameter of 60.4 mm, and with a key of…
A:
Q: An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley…
A: Given data θ=2.89 radv=29.36 m/secA=366 mm2ρ=1000 kg/m3μ=0.3 Here, v is the velocity, A is the area…
Q: Air at p = 1 atm enters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet…
A: Given data: ◆ The diameter of thin walled tube: D = 5 mm = 0.005 m ◆ The length of thin walled tube:…
Q: simply supported beam of length L and cons ed from the left end. The magnitude of maxin
A: given:y=woL4π2EIcosπxL
Q: UPVOTE will be given! Please write the complete solutions legibly. No long explanation needed.…
A:
Q: The motor draws in the cable at a rate of v = (0.05s³/2) m/s, where s is in meters. The crate has a…
A:
Q: An aircraft skin panel that is part of a commercial airline is to be made from aluminium alloy…
A:
Q: Define the drill press center pulley bearing replacement.
A: solution of above problem is below:
Q: What is the Btu/hour output of an electric heater rated at 15 kilowatts?a. 51.15 Btu/hourb. 51,150…
A: As we know that 1kW = 3412 BTU/hr The. We need to convert 15 kW to BTU/hr
Q: determine the average normal stress developed in each post when post B is heated so that its…
A:
Q: 4 Calculate the isothermal and polytropic work of a reciprocating compressor and thus deduce the…
A: given; initial volume(V1)=0.1m3initial pressure(P1)=1bar =100kpainitially…
Q: Ball A (1kg) has a velocity of +10m/s and impacts the stationary Ball B (10kg). If the Coefficient…
A:
Q: Calculate the maximum normal strain in the bar in με.
A:
Q: A general basic vibratory system consists of mass and spring. Figure Q1 shows the vibration…
A: Given : To find : -Sketch free body diagram of the system together with the action and…
Q: Part A Determine the angular velocity of the generator pulley B, measured clockwise Express your…
A: Given dataωA=90 rad/s rA=75mmrD=25mmrB=100mm
Q: segment, W is the weight of the arm of mass, m, moving the arm in abduction/adduction. If we had…
A: solution of above problem is below:
Q: 1. Steam at 5.0mpa, 410°c expands in a Rankine engine to 0.036MPa. For 60 000kg/hr of steam,…
A: Introduction: In a steam power plant, the Rankine cycle is employed to generate electricity. The…
Q: Draw the major components of a PWR and a BWR
A:
Q: A runner wants to finish a 576 m race in 68.4 seconds. He accelarates from rest and attained his…
A: Total race (DR)=576 mT=68.4 sect1=8.9 sec Need to determine the maximum constant velocity of the…
Q: Determine the magnitude of the pin force at A. Assume W = 875 lb, a = 4.3 ft, b = 3.3 ft, r = 9 in.…
A:
Q: A flange bolt coupling consists of eight 0.375” diameter bolt on a bolt circle 11” diameter, and…
A:
Q: The deflection curve for a simply supported beam of length L and constant flexural rigidity EI is…
A:
Q: A projectile is launched with a speed vo= 26.7 m/s from the floor of a 4.3-m-high tunnel as shown.…
A:
Q: Brake linings should be replaced when __ .a. linings are worn to within 1 /32 inch of a rivet headb.…
A: When brakes are exposed to wet, damp conditions, such as after a rain storm, pads may exhibit a very…
Q: What is the purpose of the internal overload protector inthe compressor motor?
A: Relays that detect overloads shield the motor, motor branch circuit, as well as motor branch circuit…
Q: As pictured below, you have a box, of unknown mass m, and push it against a spring, k = 100 N/m,…
A: Write the given data. k=100 N/mD=20 cm=0.20 m
Q: Draw a series circuit with a thermostat,a low-pressure switch, and a highpressure switch used as…
A: To draw this circuit, we have to consider the function of each component. The thermostat is used to…
Q: The figure shows a bar in equilibrium position resting on the floor at point A and on the wall at…
A:
Q: A hexagonal pyramid, base 30mm side and height 75mm long, is resting with its base on HP with one of…
A: The Pink shaded region represents the true shape of the section. The blue line represents the true…
Q: Parallel circuits are used in the airconditioning industry to __________.a. supply the correct line…
A: Most loads use line voltage as their power source. The parallel circuit allows the line voltage to…
Q: A model of a spring/mass system is 4x" + e-0.1tx = 0. Byinspection of the differential equation…
A: The given equation is 4x''+e-0.1tx=0 Now we have to find out the behavior of the system over a…
Q: Determine the maximum speed (m/s) that the cars of the roller coaster can reach along the circular…
A: Givennormal acceleration limit an=2.193gand radius of the curvature r=25m
Q: ▼ Determine the angular velocity w of the bar. Express your answer in terms of the variables 0, vo,…
A:
Q: Q5: A centrifugal pump running at 900 rpm and delivering 0.3 m³/s of water against a head of 25 m,…
A:
Q: meter with inclined tubes as shown in figure. The value gree (Take g=9 81 m/s²)
A: given:PA=20KPaPB=40KPaρw=1000kg/m3ρhg=13600kg/m3
Q: State the standard conditions for water to boil at 212°F.
A: In this problem, it is asking about the standard conditions for water to boil at 212°F.
find the reaction at both support
Step by step
Solved in 3 steps with 5 images
- The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900 lb, find the smallest possible sag hC at C.The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.The cable is loaded by an 80-lb vertical force at C and a horizonal force P at B. Determine P.
- Show that all diagonal members of the truss carry the same force, and find the magnitude of this force.Find the forces in the three cable segments and the angles 1,2, and 3.The cable of mass 1.8 kg/m is attached to a rigid support at A and passes over a smooth pulley at B. If the mass M = 40 kg is attached to the free end of the cable, find the two values of H for which the cable will be in equilibrium. (Note: The smaller value of H represents stable equilibrium.)
- The woman is trying to move the crate of weight W by pulling on the rope at the angle to the horizontal. Find the smallest possible tension that would cause the crate to slide and the corresponding angle .Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.
- Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.The cable AOB weighs 24 N/m. Determine the sag H and the maximum tension in the cable.