Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at 200 degrees Celsius being 1/420 per oC and resistance at 420 oC being 200 ohms. 1. Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at200 degrees Celsius being 1/420 per °C and resistance at 420 °C being 200 ohms.

1. It is given that: R1=200 ΩT1=420°CT2=500°CT=0°Cα=1420/°C

Answered: Find the resistance of a conductor at…

Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at 200 degrees Celsius being 1/420 per °C and resistance at 420 °C being 200 ohms.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter10: Using Wire Tables And Determining Conductor Sizes

Section: Chapter Questions

Problem 10PP: Determine the ohms-per-mil-foot of an aluminum conductor located in an area with a temperature of...

See similar textbooks

Related questions

Q: In the circuit shown, determine the following: The equivalent reactance and its nature (inductive o...

Q: Determine the thermal voltage in mv for a silicon diode at a temperature of 20 degrees centigrade. (...

A: In this question, Find the thermal voltage if temperature T= 20°C We know Boltzmann constant K= 1...

Q: 2. What is the process of converting a signal from a given rate to a different rate? a) Sampling b) ...

Q: 3.. A coil of 1000 turns is uniformly wound on a ring of non-magnetic material, the mean diameter be...

A: self inductance of the coil = number of turns2×permebility×area of the coremean length of the core. ...

Q: 2. How much is the inductance of a coil that induces 500 V when the current changes at the rate of 5...

A: We need to find out inductance for given coil .

Q: An electric kettle working at 220 V heats upto 2 liters of water from 20 °C to 100 °C in 2 minutes. ...

Q: Determine the noise current for a diode with a forward bias of 45.15 mA over a 100 kHz bandwidth. a....

A: For a diode - The forward bias current is,IFD=45.15mAThe bandwidth is,BW=100kHz

Q: With a neat logic diagram and shifting table, explain the shifting of given bit stream 1011001 enter...

Q: Find the approximate increase by the use of differential, In the volume of the sphere if the redius ...

A: Given,Rinitial=2R'(final)=2.05Change in radius dR=0.05 ∆R=0.05

Q: shunt-wound motor runs at 600 r.p.m from a 230 V supply when taking a line current of 50 A. its arma...

A: In this question we will solve questions related to DC shunt wound motor ....In first part we will f...

Q: Using Y-∆ or ∆-Y transformation, determine the equivalent resistance and total current

A: In this question, Determine the equivalent resistance and total current using Y-∆ or ∆-Y transformat...

Q: Determine the value of the resistance R in the circuit shown. 5 ko 10 ko 25 V+ ib 4 ip R |0.5 mA

Q: Determine the thermal noise voltage for a component operating at -60 °C having a bandwidth of 50 kHz...

Q: Find the power absorbed by the dependent source in the circuit shown. Assume I=2 A, R1=9 Ohms, and R...

Q: Enumerate and explain briefly the three basic types of alternating current circuits.

Q: 2 v, ww I5V

Q: The expected value of the voltage across a resistor is 102V. However, measurement yields a value of ...

Q: Two resistors 5 kN and 20 k2 are at 27°C. total noise voltage for the parallel combination? what is ...

Q: 3. Determine the voltage across R2 for the first and second diode approximations. Diode: Si, r = 10 ...

A: Solve the problem

Q: KVL 06 What is the total current (1) flowing through the below circ I V2 5ko 1 ko 10 V 15 V 4 kQ V3 ...

A: Given,

Q: For a given circuit, L=0.500 H, R=10.0 2, C = 250 µF, and E = 100 sin 100xt. Find the equation relat...

A: L=0.5H R=10Ω C=250ΩE=100 sin 100πtLdIdt+1C∫I dt+RI=EI=dqdtL d2qdt2+1C×q+Rdqdt=E0.5 d2qdt2+1250×10-6...

Q: circulating pump consumes 450 W for 24 hr a day. a. Determine the energy consumed for a one-year pe...

A: In this question , power consumed by circulating pump is given for some time period....We have to fi...

Q: Use superposition to find the voltage v in the circuit shown. ЗА 10Ω ww www + V - 40 V 10 Ω 2V,

A: In this question we will find voltage across 8 ohm using superposition theorem.... Superperposition ...

Q: LO the score) Electric Potential 1. How much work does the electric field do in moving a proton from...

Q: 93) for the ceisreit shown in fig(3)., determine the current in 502 resistor refuerce dinection show...

A: The given circuit is shown below:

Q: 2Ke 60pF {2 00&

Q: 11 To increase the voltage in the system, :the modules are connected in (ähäi 2) .Series .Parallel

A: Given, To increase the voltage of the system, the modules are connected in ____.

Q: Find thevenin's equivalent with respect to terminal "ab

A: This question belongs to electrical circuit theory . It is based on the concept of Thevenin's theore...

Q: 1. Three impedances of 10453.13°N are connected in delta to a three-phase, CBA system with an affect...

Q: 6. What is the electric potential 15.0 cm from a 4µC point charge? tiel diatonoo of 15 cm What is th...

A: As per our company guidelines we are supposed to answer only first question kindly repost other ques...

Q: 4.a. What's the typically acceptable maximum BER value in a multimode fiber? A. 10–7 B. 10–6 C. 10–9...

A: Answer 4(a), The typically acceptable maximum BER value in a multimode fiber is 10-9. This value is ...

Q: 4. Find the branch current analysis at the circuit shwon in figure below. a I R3310 N R1 ils, 2 E, 1...

A: Branch current analysis means I am using kirchoff current law(KCL).

Q: The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculat...

A: We have given; The plates of thickness 1.5mm diameter =3.0mm stress in the plates is limited to 15 ...

Q: 2. What is the process of converting a signal from a given rate to a different rate? a) Sampling b) ...

A: Option - C is the correct answer for the above question. I have provided explanation below. Please ...

Q: Grinding Force Desired DOC Force K¸(Rs+1) Machine Stiffness 1 2 Deflection ms + bs + k Control Filte...

A: Given

Q: Determine the current (in mA) through the Silicon diode.

A: Find current through the Silicon diode We are know that Silicon diode drop voltage=0.7 Volt Germani...

Q: Bidirectional shift register can be used to perform multiple operations. Design a 4-bit bidirectiona...

A: Solution:- AD-FF gives output same as input upon giving a clock pulse. Here, P3, P2, P1,P0 - Parall...

Q: Power rating of a motor drawing a current of 40 A at 400 V is?

Q: A generating station has a demand of 25 MW, a load factor of 60%, then the average demand will be:

A: Given: A generating station has, Maximum demand = 25 MW Load factor = 60 % Average demand =?

Q: 3. Using KVL method, find the current supplied by 12 V battery. R3$120 10 V E," 12 V Figure 4

Q: Power rating of a motor drawing a current of 40 A at 400 V is?

A: Given: A motor drawing a current, I = 40 A At voltage, V = 400 V

Q: What is the characteristic time constant for a 6 mH inductor in series with a 3 Q resistor?

A: Given a series RL circuit having, Resistance, R=3 Ω Inductance, L=6 mH

Q: 2. Draw and explain the difference between clipper circuit and clamper circuit output waveform

Q: Q4 // Write the Boolean algebra laws for OR gates?

A: OR gate - A two input OR gate will give you a logic 1 output if EITHER or BOTH of its input are at l...

Q: Write a Boolean expression for the output of the logic circuit. #1: z=1 z #2: z=xy+w #3: z=xy+y+w #4...

A: Given: Logic circuit,

Q: 4.8.1 In the circuit shown in the image below, if V1 = 4.7 V and R1 = 5.2 Q, according to the superp...

A: This question belongs to circuit theory . It is based on the concept of super position theorem . In ...

Q: Fill in the blanks: 12 V Si GaAs 4.7 k2 Vo= V, 1 decimal Which diode is OFF? Si or GaAs

Q: A coil of wire of resistace 50 ohm is embeded in a block of ice. What is the amount of ice melted in...

Q: We would like to sample the signal x (t) = cos(4rt). What is the smallest frequency, in Hz, that cou...

A: This question belongs to communication system . It is based on the concept of sampling frequency for...

Q: When the load impedance is equal to the characteristic impedance of the transmission lines, then the...

A: Solve the problem

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at 200 degrees Celsius being 1/420 per oC and resistance at 420 oC being 200 ohms.

1. Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at
200 degrees Celsius being 1/420 per °C and resistance at 420 °C being 200 ohms.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the ohms-per-mil-foot of an aluminum conductor located in an area with a temperature of 104F (40C). Use the NEC to determine the ampacity of the following conductors.
One thousand circular mils or 1 kcmil is sometimes designated by the abbreviation MCM75C. Data for commercial bare-aluminum electrical conductors lists a 60 Hz resistance of 0.0080 ohm per kilometer at for a 793-MCM AAC conductor. Determine the cross-sectional conducting area of this conductor in square meters. Find the 60 Hz resistance of this conductor in ohms per kilometer at 50C.
Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All strands have the same radius r.
The resistance of a cylindrical brass conductor has a resistance of 0.00108 ohm with 0.5 cm diameter and 3 m long. Determine the resistance of a cylindrical conductor of the same material at the same temperature, and having a diameter of 0.25 cm and a length of 8 m
The resistance of a cylindrical brass conductor, 0,5 cm diameter and 3 m long, is 0.0108 ohm. Determine resistance of a cylindrical conductor of the same material at the same temperature, and having a diameter of 0.25 cm and a length of 8 m.
Compute the resistance of a conductor whose resistivity is 20.54 ohm-CM per foot with circularc ross-sectional area of 38 mm2a nd length of 5,000 meters. If the conductor is drawn until its resistance becomes 10 ohms, what will be its new length?
Compute the resistance of a conductor whose resistivity is 20.54 ohm-CM per foot with circularcross-sectional area of 38 mm2 and length of 5km. If the conductor is drawn until its resistance becomes 10 ohms, what will be its new length?
A lead conductor is 5cm in length and 8 sq. cm in cross-sectional area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of leads is 22x10^-8 Ω-m.
A solid cylindrical aluminum conductor 25 km long has an area of 336,400 circular mils. Obtain the conductor resistance at 20C and 50C. Find the AC resistance per Km of the cable at 50C. Assume a skin-effect correction factor of 1.02 at 50 Hz. The resistivity of aluminum at 20C is 2.8x10-8 Ωm
A lead conductor is 5cm in length and 8 sq. cm in cross-sectioned area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of lead is 22x10^-8 Ω-m.
Compute the resistance of a conductor whose resistivity is 20.54 ohm-CM per foot with circularcross-sectional area of 38 mm2 and length of 5,000 meters. If the conductor is drawn until its resistance becomes 10 ohms, what will be its new length?
The diameter of a cylindrical conductor A is 6.0 mm, and its length is 2.0m. The diameter and length of a cylindrical conductor B of the same material as A are 3.0 mm and 1.0 m. The resistance of conductor B is 0.02 ohm. Determine resistance of conductor A, its temperature being the same as that of B.