Answered: Find the resultant shear stress at…

Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the weld is 10mm. Also show shear stresses on the weld. 300 100 150 20 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse…

Q: A rectangular plate (0 =22") is formed by welding two triangular plates shown in figure. The plate…

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: Consider the figure shown below: Ay - 300 mm The undeformed length of the bar is 300 mm. It is…

A: Given is Length of the bar = 300 mm

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: fF=6 kN as in the figure. Find the maximum normal stress occurring in section (a-b). Sh ne stress…

A: Answer is given below

Q: The figure shows the stresses at a point. Determine the principal stresses and the maximum shear…

Q: For the state of plane stress shown in Figure-1. below; a) Draw Mohr's circle, b) Find the maximum…

A: Given Data: The stress in the x-direction is, σx=-20 MPa. The stress in the y-direction is, σy=90…

Q: In figure below, the shear force (Q) is equal to 150 kN. What is the shear stress (t) at the neutral…

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

Q: The point A in the following plot represents: A or 0.5 -180 -90 90 180° -0.50, Graph of normal &…

Q: cross section at the wall is shown, with points of interest A, B, C, and D. Evaluate the potentially…

Q: Find the stress in each cord for the system shown in fig. below, if the cross section ?area of each…

Q: The state of plane stress at a point is represented by the element shown in the figure. в, - 200 Мра…

A: note: Mohr's circle is used to calculated the principle stresses

Q: As shown in the figure, the forces P1 and P2 are applied to the end A of the rod AB welded to the…

Q: shear stress in t

A: Given data sigma x = -100 MPa sigma y = 0 sigma xy = 0 required normal stress at 300 shear stress…

Q: For the top (level n-n) of the web in Figure Q1.12 the shear stress due to a shear force V in the…

A: Given: Find the First moment of the area above n-n about the neutral axis.

Q: Find the minimum principal stress for the stress case given in the figure.

Q: 950 MPa 70 MPa 210 MPa 60

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Introduction: The load-bearing capability of a weld relates to how much load it can withstand before…

Q: Find the normal stress value on the new x-axis obtained by turning 53° clockwise of the stressed…

Q: Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the…

Q: The screw of the clamp exerts a compressive force of 500 N on the wooden blocks. The cross section…

Q: QUESTION 15 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is…

Q: Mohr's circle for an element is shown below. If each grid is 15 MPa then the maximum shear stress…

A: Mohr's circle is a two-dimensional graphical depiction of the Cauchy stress tensor transformation…

Q: Find the major principal stress, average normal stress and maximum shear stress for the following…

A: From the given Mohr's circle σx=80 MPaσy=-20 MPa

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

A: Given data θ=21° Compressive stress=2.9 Mpa. Tensile stress=19 Mpa.To determine The normal…

Q: 3. Represent the stress state at point A on the web of the beam in terms of the principal stresses…

Q: Q2/ According to the figure below find the size of the weld. Take permissible shear stress for the…

Q: if the cross-section shown in the figure has a shear stress of 300psi at point P( located 0.25 in…

A: Find the shear force. Given :- shear stress at point P is 300 psi.

Q: The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given…

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

Q: 14 ksi C ):- Draw the Mohr's Circle of the stress element shown in figure. Find:- 12 B 20ksi A 1)…

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

Q: * The state of plane stress at a point is represented on the element shown in the figure. The…

A: GIven σx=10MPaσy=30Mpaτ=20MPa

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

Q: find the normal stress and shear stress in the plane C in the element subjected to stress seen in…

Q: according to the given and show them on the stress element.

Q: By using Mohr's circle on the element subjected to stresses in the figure; a) Find the principal…

A: GIVEN :-σx=-210 MPaσy=950 MPaζxy=70 MPaSOLUTION :-finding the center of Mohr's circle,Center:…

Q: THE MAGNITUDE OF THE LOAD ( F= kN) WILL BE THE SUMMATION OF ALL THE NUMBERS IN YOUR STUDENT NUMBER.…

A: In this question, the first step is to find the components of the applied on the point of…

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

A: GIVEN: σx=-2.3 MPa σy=13 MPa θ=23° TO FIND: The normal stress and Shear stress on the weld plane.

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

Q: 1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: A vertical pipe column with an outside diameter of D=114 mm and inside diameter of d=102 mm supports…

Q: Q2) Look at the Mohr Circle and find (the scale is 1 cm-10 MPa) 1. Normal and shear stress at points…

A: Since we only solve upto three subparts at a time, we will solve the first three. Please specify the…

Q: If the wood joint shown in the figure has width of 200 mm, determine the average shear stress…

Q: The cross-section of the beam is rectangular everywhere, and the size of the cross-section is given…

A: Given width of beam w=50mmhieght of the beam h=100mm

Q: Q#2: Explain the absolute maximum shear stress. Construct Tresca's hexagon by explaining all the…

A: Given data To explain the absolute maximum shear stress and construct by Tresca’s hexagon by…

Question

Find the resultant shear stress at point
A & C for the weldment shown in the
figure. Leg size of the weld is 10mm.
Also show shear stresses on the weld.
-300
100
B
G,
150
20 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the resultant force at the support A?
Show that the normal stress in case of an annular fillet weld subjected to bending is given by σ=5.66M/πsd² Where M = Bending moment; s = Weld size and d = Diameter of cylindrical element welded to flat surface.
The state of stress at a point in a member is shown on the element. Suppose that σx = -50 MPa , σy = -120 MPaMPa , τxy = -30 MPa . Determine the shear stress component acting on the plane AB. Tx`y`=?
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
The shaft is used to transmit 30 hp while turning at 600 rpm. Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in.
find the average shear stress on the section of the inclined member if we were to cut it horizontally.
The state of stress at a point in a member is shown on the element. Suppose that σx = -50MPa , σy = -120MPa , τxy = -30 MPa . Determine the normal stress component acting on the plane AB. σx′=?
find the stress at point A and point B
Find normal stresses and shear stress at the given inclination ..using mohr circle
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.