Find the safe axial load fo a 4.5m column. pin connected at its ends, and laterally braced about itrs weak axis at midspan A W-6X20 section will be used, having the fo lowing properties: Fy = 248 MPa A = 3790mm2 Ix = 17.232 x 105 mm4 ly = 5.536 x 10 mm What is radius of gyration with respect to bending along the strong axis?

Find the safe axial load fo a 4.5m column. pin connected at its ends, and laterally braced about itrs weak axis at midspan A W-6X20 section will be used, having the fo lowing properties: Fy = 248 MPa A = 3790mm2 Ix = 17.232 x 105 mm4 ly = 5.536 x 10 mm What is radius of gyration with respect to bending along the strong axis?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please show complete solution and drawing.Problem 1. The indeterminate frame shown below is loaded with lateral forces applied on each level.Using Factor Method, draw the approximate moment and shear diagram of the structure due to theapplied loads. Show your complete solution from the determination of girder/column factor, carry overfactor, girder/column moment factor up to computation of end-moment for each member.GIVEN: a) 45 kNb) 44 kNc) 15 kNd) 2.80 me) 3.30 mf) 3.75 mg) 3.50 m
A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 8-ϕ25 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa.Calculate the nominal axial strength of the column in kN.A. 7 047 B. 5 638C. 4 580 D. 6 342 Calculate the center to center spacing of ties for confinement.A. 200 B. 400C. 500 D. 300 Where is the plastic centroid measured from the short edge of the column?A. 200 B. 400C. 500 D. 300 Calculate the steel stress (MPa) in the middle layer of bars at balanced strain condition.A. 31.37 comp B. 43.52 compC. 31.37 tension D. 43.52 tension Calculate the nominal axial strength in kN of the column at balanced strain condition considering bending about the strong axis.A. 3,420 B. 2,500C. 2,875 D. 3,846
s shown in the sketch, an interior column AB in a steel frame carries a factored axialcompressive load, Pu = 1540 kips. The column is braced at the top and bottom and the mid-height in the perpendicular plane, and sidesway in the plane of the steel frame is allowed. Thecolumns are 12-ft long, and the columns above and below the column AB are the same size asAB. The adjacent girders are W 18×50 and are 32-ft long. Use A992 steel with Fy = 50 ksi,select the lightest W-section for the column AB. Use stiffness reduction factor where applicable.
Determine the slope of end A of the cantileveredbeam. E = 200 GPa and I = 65.0(106) mm4.
A spiral column is to carry a factored load of 1900 kN and a factored moment of 24 kN-m such that it can be analyzed as pure axial. Initially, 2.5 % steel ratio is desired. Use 16 mm main reinforcement, 10 mm spiral with 30 mm clear cover to ties, f'c = 27.6 MPa and fy=415 MPa. 1. Design the column dimensions and should be multiples of 50 mm. (in mm) 2. Number of steel reinforcements 3. Pitch or spacing of spirals in mm
A rectangular beam has b=250mm, d=330mm, fy=414,fc'=20.7MPa. Determine the the maximum design moment if the beam is singly reinforced.
A rectangular, tied column 480 mm wide along x-axis and 540 mm wide along y-axis is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 21 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only.
An axially loaded column W360 x134 hasits weak axis braced at the third points.The overall length of the column 8 m. UseA 572 grade 50 Fy=345 MPa. The columnis pinned connected at both ends.Properties: rx = 155 mm, ry = 95 mm,A = 17,105 mm2 Determine the slenderness ratio withrespect to y-axis. Determine the slenderness ratio withrespect to x-axis. Determine the critical slendernessratio. What is the nominal compressivestrength of the steel column?
The beam CBA is supported by a ball and socket support at A and two cables BD,BE as shown. It is loaded by two forces F=945 KN and P=315 KN.
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
A flitch beam is composed of two 50x300mm planks reinforced with a 12.5mm steel plate as shown. Assume that continuous lateral support is furnished by a floor system supported by the beam. Use A36 steel with an allowable bending stress of 150 MPa, Fy = 250 MPa. Es = 200,00MPa, Ew = 7692MPa, fw = 4.3 MPa. The beam is on a simple span of 4.8m and supports a uniformly distributed load of 7.3 kN/m which includes the weight of the beam. Allowable stresses for shear: Steel: fv = 0.60Fy MPa Wood: fv = 0.58 MPa Determine the following: a.) The resisting moment of the flitch beam b.) The applied moment to the flitch beam c.) The shear capacity of the flitch beam
A 550mmx800mm column reinforced with 12 pcs of D20mm (3 bars each on outer ends). The column carries an ultimate load of 3500kN at an eccentricity 325mm. Assuming concrete strength and steel strength to be 25MPa and 420MPa respectively. Take clear cover to be 40mm and diameter of ties to be 10mm. Determine the balanced compression depth, mm. Determine the balanced moment, kN-m. What is the design strength, kN.