Find the total punching force, given that the shear stress of the material of which the 2mm thick piece is 12 mm 34 mm 200 mm made is 420 N/mm2. 100 mm 17 mm

Q: The value of shear stress in the principal plane is Resultant stress Maximum Zero O Minimum

A:

Q: Find the applied force which produce stress of 22 N/mm2 on cross sectional area of 5.98 mm2

A: Given data : Stress σ=22 N/mm2 Cross sectional area A=5.98 mm2   Required : Applied force

Q: Q:: Determine the force necessary to punch a 10 mm dia. Hole in a 20 mm thick mild steel plate, if…

A: Given data Diameter (d) = 10 mm Thickness (t) = 20 mm Shear strength = 10 MPa

Q: The state of stress in two-dimensionally stressed body at a point is as shown in Fig. Determine the…

A:

Q: Find the Force applied Stress=0.99 N/mm2 Area 4 mm2

A: Given data : Area A=4 mm2 Stress σ=0.99 N/mm2   To find : Force applied

Q: Determine the stress area in mm2 of a 1.75 - 8UNC bolt.

A:

Q: 2- Find the total change in length of the beam shown : A=200mm2 E2 = E3 = 150 GN/m² %3D 50 kN 30 kN…

A:

Q: Forces are applied as shown at point D of the steel post shown.Since the diameter of the pole is 60…

A:

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73…

A: find the maximum shear stress in the shaft.

Q: The force on a wagon wheel is F=2000 N. Find the axle diameter of the wagon wheel made of Fe50…

A: To design a machine element, we need to analyze the forces applied to the element. The forces can…

Q: Q2/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm2.

A:

Q: Transform the following 1--Bar to psi = Lbf/in2 2-Hp to kW = kN.m/s 3-\kW to hp

A: You have posted multiple questions in a single window. As per the guidelines I am able to answer…

Q: Find the value of stress Force 2.2 N Area=2 m2

A: To find :  The value of stress .  Given : The force is  F=2.2 N The Area is A=2 m2 Formula used :…

Q: Given the internal radius of the pipe is 2 cm, the external radius is 2.4 cm and the length of the…

A:

Q: Find the internal force at the cross-section G 2.Find the average of the shear units in Pin A

A:

Q: Find the force which produce stress 22 N/mm2 on cross sectional area 2 mm2

A:

Q: The ratio of yield stress to allowable stress is called the Soloct onot

A:

Q: Determine the average shear stress in the tube if the dimension a = 200 mm

A:

Q: Q1-Calculate the force needed to guillotine a sheet of metal 5 mm thick and 0.8 m wide given that…

A:

Q: 56 mm 32 mm 26 mm 66 mm 32 mm 28 inm 8 mm

A:

Q: Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of…

A: The cross-section can be drawn as:

Q: In this figure is a strut and a cable which was use to lift a body. If the strut and a cable has a…

A:

Q: Determine the shear stress (in Mpa) in the 35.29-mm-diameter pin at B that support the beam if P =…

A:

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: We are restricted to solve one question at a time. Please ask other questions in the next post.…

Q: Qi: Determine the force necessary to punch a 10 mm dia. Hole in a 20 mm thick mild steel plate, if…

A: Given data:- D = 10 mm t = 20 mm Shearing strength =10 N/mm^2

Q: Q3. Determine the inner and outer diameter of the hollow shaft which will replace a 76 mm solid…

A:

Q: ust for checking determine if true or false 1.) The cross-sectional area of a body is its total…

A:

Q: he region of safety in maximum shear stress theory contains which of the given shape *

A: The region of safety in maximum shear stress theory contains Hexagon.

Q: Q1: In the figure. Determine the FB? If EMA = 0 23.5 kN 1.5 m B 9.81 kN 2 m-

A: Given data as per question Force applied at end of the structure = 23.5 KN Force acting at mid of…

Q: 4. The rubber block seen below deforms by a distance 6 = 0.02 mm. The deformed shape is shown by the…

A: Given data:

Q: 883KN V V V V V V V V ww.cos 3mm

A: given; weight density(w)=883KN/mlength of beam(l)=500mm                                =0.5mdiameter…

Q: Question 1: Given that Tattow = 50 MPa for the rod AB and tattow = 25

A: given:shear stress for AB =50Mpashear stress for BC=25MpaT=1250N-m

Q: A 8-inch diameter rivet undergoes a shearing force of 1,712 pounds from plates. Determine the…

A:

Q: 2. For the state of plane stress given, determine the principal planes, the principal stresses and…

A: givenstress in x direction σx=100MPa   tensile stress in y direction σy=-60MPa  compressive shear…

Q: At a certain point in an elastic body direct stresses of 150 N/mm² tensile and 100 N/mm² compressive…

A: Given:σx=150N/mm2σy=-100N/mm2Principal stress, σ1=180N/mm2

Q: Find the value of P and the distance x so that the bar AB remains horizontal. Take the radius of the…

A: The 2000 N weight acting on the left rod. The force P and the distance x from A needs to be…

Q: What is the Shear Force,V?

A: To define: The shear force. Concept used: Shear force: Shear force is an internal force in any…

Q: The shaft below is subjected to the forces shown. Calculate the magnitude of the bearing forces at…

A:

Q: The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz =…

A: given; σx=120MPaσy=55MPaaσZ=-85MPaσxy=-55MPaσxz=-75MPaσyz=33MPa

Q: Given data: Force3D3 N Stress3D6 N/mm2 Find area

A: Given data : Stress=σ Force=F   To find : Area

Q: A force of 400N is applied on a area of 20m ^2 . Determine the stress generated by the force .

A: The problem is based on mechanics and can be solved as:

Q: A box is dragged across a floor by using a rope that makes an angle of 30° with the horizontal.…

A: Given Data⇒θ=30° with the horizontalTension in ropeT=50 lbf-mhorizontal distance mooved is 30 feet

Q: A 3 inches diameter solid shaft is desired to replace a hollow shaft in which the weight of hollow…

A:

Q: d the shearing stress (in MPa) experienced by a rivet of radius r=19 mm if a shear force F =389 kN…

A:

Q: case where ki= k2 = k3 = k, m m3 = m, and m2 2m.

A:

Q: Find the value of force which produce stress of 1.2 N/mm2 if cross sectional area is 0.5 mm2

A: Given data : Stress=σ Area=A   Find : Force

Q: 2. If 75 N/mm is the maximum shear stress and 50 kN-m is the torque acting on a solid shaft, then…

A: Given: Maximum shear stress τmax = 75 N/mm2 = 75000 kN/m2 Torque acting on a shaft      T = 50kN-m…

Q: 20 kips 45° 30 kips

A: for the given system of forces  To determine  the resultant force applied

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.