Find the transfer function, G(s) = X3(s) / F(s), for the translational mechanical network without using newton law. M₁ = 8 kg|Frictionlessf(1)► X₁ (1) —-X₂ (1)1 N/moooo0000 M₂-3 kg4 N-s/mCFrictionlessਮਈ-X3(1)oooo16 N-s/m 15 N/mFrictionless

To determine: The transfer function.

Answered: Find the transfer function, G(s) =…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing at a rate of 25 gpm in a pipe and at one end of the pipe, the internal diameter is 2in and the gauge pressure is 10psig, and at the discharge end 20ft away horizontally, the water discharges into the atmosphere through a 3.5-in ID pipe. Determine the friction in ft of water?
FLUID MACHINERY A 200-mm x 150-mm x 250-mm direct-acting duplex pump delivers water at a temperature of 150oC. The piston rod diameter is 40 mm and the slip is 10%. The pump operates against a pressure of 1500 kPa. Determine a. the theoretical capacity of the pump Answer : __________________ m3/minb. the actual capacity of the pump Answer : __________________ m3/min
The tank in the form of a right-circular cone of radius 5 ft and height 23 ft standing on its end, vertex down, is leaking through a circular hole of radius 3 inches. Assume the friction coefficient to be c=0.6 and g=32ft/s2. Then, the correct equation governing the height h of the leaking water is dh/dt= _______________ If the tank is initially full , it will take it ___________ secs to empty correctly.
Friction In Pipe 1. In this experiment, you are required to measure the left and right levels (limb reading) of the manometer. Apparently, the right side is higher than the left. Explain what has actually been measured?
What work is done on a level track in bringing the velocity of a train weighing 200 tons from zero to 30 mi/hr, if the frictional resistance at any velocity is 12 lb/ton, and if the change in speed is accomplished in a length 5280 ft? If the track were a 1% upgrade, what would be the additional work to be done?
A fan can deliver a total pressure of 379 mm of water gage. The boiler requirement is 42,295 m^3/hr of standard air and the mechanical efficiency is 66%. Determine the brake power in kW.
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from Ato B is 5 cfs. a) Determine the head loss in feet in PIPE 1 and PIPE 2 b) Determine the head loss in feet in PIPE 5 c) Determine the flow in the upper branch pipe Q2 in cubic feet per second d) Determine the total head loss in feet between the inlet A and the outlet D
A pipe of 50 mm diameter and 4,5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1,25 km long and taken from a point distance of 1,5 km from reservoir A, which leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f=0.0075,and neglect minor losses.
13.71. A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3 /s of oil, sp gr 0.88, and the pressure in the smaller pipe is 265 kPa, what resultant force is exerted on the contraction, neglecting friction? Ans. 15.4 kPa.
The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Area of the plunger Calculate 1-area of the plunger 2-N0 of stroke 3_area of ram 4_area of the ram plunger 5-power required to drive the plunger
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS