Answered: Find the value of strain if stress is…

Engineering

Civil Engineering

Find the value of strain if stress is 45 Mpa and modulus of elasticity 70 MPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 14CQ

See similar textbooks

Related questions

Q: Problem 03. A beam having a span of AB equal to 9m has an overhang of BC equal to 2m. It carries a…

Q: The moist unit weight of a soil at 18.32% moisture is 17.23 kN/m3. Determine the mass of water (kg),…

A: Given data of soil sample :- Unit weight of soil = 17.23 KN/m3 Moisture content (w) = 18.32% =…

Q: Determine roller support reaction

A: Given data : The value of Point load P=15 KN The value of uniformly distributed load w=25 KN/m…

Q: 000

Q: rectangular foundation is 3 m x 4m in plan is acted upon by a inclined force of 50 kN at an angle of…

Q: wing that is related to transportation engi

A: A working sketch or blueprint is one that is based on explanations. It's finished with a detailed…

Q: Two similar clay soil samples were pre-consolidated in triaxial equipment with a chamber pressure of…

Q: Eficient Eficient -. 0.98 - 0.99 charge of 0.62 Determine of contraction of 0.63. of velocity for…

Q: Discuss the influence of the water cement ratio, entrained air and cement content on concrete…

A: The ability of a structure to carry loads on its surface without cracking or deflection is known as…

Q: ht repre part las = elocity v = 6 ft/sec in the direction shown and Las acceleration components ax…

Q: Draw the axial load, shear and bending moment diagrams for the frame shown. 30 kN/m B C 3 m 5 m +…

A: We will calculate reactions and draw FBD.

Q: Water rises in a capillary tube of diameter 0.2 x 10-2m, upto a height of 1.5cm. The surface tension…

A: Given data : The value of capillary rise h=1.5 cm The value of diameter of tube d=0.2×10-2 m The…

Q: Calculate the total area required for placing the quarry tiles on the internal walls in this…

A: There are two short walls and two long walls, And there is a deduction in area in the place of the…

Q: draw shear and bending moment diagram. Show completed solution 45 AN 45 AN 71kN/m Lisat tiset

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A one-dimensional column test was conducted on a sediment sample. The column had a crosssectional…

Q: What is a rule of thumb?

A: A rule of thumb is a general or approximate way of doing something that is based upon common…

Q: 8 kN B 8 kN 20 kN m. C₁ m- 0.25 m Reaction at support A=? D 000 -0.75 m-1 m- 15 kN/m -1m-

A: Equilibrium condition in x direction and in y direction . Statically determinate beam. Moment at…

Q: Find the value of coefficient of friction if friction force is 230 N and Normal force is 800 N

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: The saturated unit weight of a soil is 19.8 kN/m³. The moisture content of the soil is 17.1%.…

A: Given data in question Saturated unit weight Water content To find out Dry unit weight

Q: The overall drag coefficient of an aircraft of weight Wand wing area S is given by Co= a +bC₂² where…

Q: 19. Determine the total active thrust, in kN/m, for a retaining wall (height 5.55 m.) with…

A: solution Given angle of internal friction φ=31°coefficient of active earth pressure…

Q: Bottom chord of truss is composed of two angle bars each having a dimension of 176 mm x 148 mm x 8.5…

A: db = 19m (dia of bolt) dh = 19 + 3 = 22mm (dia of hole) fy = 249 MPa fu = 400 MPa t (thickness) =…

Q: PROBLEM 1: The beam shown is made up of W 24 x 55 structural steel. It carries an unfactored uniform…

A: Given beam of W 24 x 55 structural steel unfactored uniform service dead load, Wd = 12.52 KN/m…

Q: I. Design a reinforced concrete beam to carry a service dead load of 15kN/m ( including its own…

A: L = number of letters of your family name = 4mP = number of letters of your family name times 20kN =…

Q: For a constant laboratory permeability test on a fine sand, the following data are given: Length of…

Q: 454 For Problems 20.17 through 20.20, use the matrix approach to solve fo the member end forces. In…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Find the value of final velocity of car U=2.5 m/s a=1 m/s2 t=3.5 s

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: 1. A baseball pitching machine "throws" baseballs with a horizontal velocity v0. Knowing that height…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness…

Q: A cantilever beam 4 m long deflects by 16 mm at its free end due to a uniformly distributed load of…

Q: 15kN A 2m 3m 25kN/m 5m 14m 4m QUE

A: Given data:

Q: Problem B Equipment Estimating Use the following information for a scraper. Actual cost (delivered)…

A: Actual cost of vehicle= $162000 Useful life = 6*1400= 8400 hrs Life of tires = 3500 hrs No of tire…

Q: The following results are obtained from a series of cone penetrometer tests. Mass of empty can, g…

Q: Given data: Maximum principal stress=38 MPa Minimum principal stress=32.5 Mpa Find maximum shear…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: (1) Determine the distance from the left support where the stirrups can be omitted using the…

A: Shear strength: - It is the strength of a material to resist shear force which acts parallel to…

Q: ОА 3 A 4 m 5 4 100 m B

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 anc wetted perimeter 12 m

Q: AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in…

Q: Differentiate Professional Engineering Cost to Construction Cost

A: Construction: - It is a term which is defined as the process in which build something.

Q: Calculate static indeterminacy of truss

A: Given data : The value of number of member in truss structure m=10 The value of joint in truss…

Q: Problem 8 A 30 cm diameter cast iron pipe conveys water at 20°C at the rate of 0.2m³/sec. head loss…

Q: A welded steel channel (Manning n = 0.015) is rectangular in cross-section, being 1.55m wide, and is…

A: what is the volumetric flowrate?

Q: Determine the right triangle side lengths, whose one angle is 45 degrees, and the hypotenuse is 5 √2…

A: The values and diagram given in the question are as follows: one angle of the right-angle triangle…

Q: A single-angle tension member, an L90 x 90 x 10, is connected to a gusset plate with 22 mm-diameter…

Q: 5. Find the net torque about point O for the two forces applied. The rod and both forces are in the…

Q: 700 lb Answers: BG= i BF = i C IVB E 6' G -6'+3' 7 F lb lb

Q: In a triaxial test for a cohesive soil sample, when the principal stresses are 483.36 kPa and 60.39…

Q: In a rectangular channel 3.5 m wide laid at a slope of 0.0036, uniform flow occurs at a depth of 2m.…

Q: A composite beam is constructed using a steel plate (10 mm x 165 mm) with two wood beams (75 mm x…

Concept explainers

Pressure and Stress

Question

Find the value of strain if stress is 45 Mpa and modulus of elasticity
70 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Determine stress and longitudinal strain
A symmetrical framework consisting of three pin-connected bars is loaded by a forceP (see figure). The angle between the inclined bars and the horizontal is a = 52°. Theaxial strain in the middle bar is measured as 0.036.Determine the tensile stress in the outer bars if they are constructed of a copper alloyhaving the following stress-strain relationship:
Show the relationship between axial stress and strain to get the axial deformation
A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curve (modulus of elasticity) is 200GPa. The bar is loadded axially until it elongates 6.5mm, and then the load is removed. How does the final length of the bar compare with its original length? (Hint: Use the concepts illustrated in figure below)
Sketch a stress versus strain graph for a material, such as mild steel, which exhibits linear elastic and plastic properties.