Mark all that apply Find the voltage across the capacitors under dc conditions10 Ω50 Ω70 ΩwwwC₁20Ω60 V1/2C2 Capacitor behaves as an open under DC conditionsCapacitor behaves as an short under DC conditionsv1 is the same as the voltage across the 70 ohm resistorv1 is NOT the same as the voltage across the 70 ohm resistorCurrent through the 50 ohms resistor is NOT zeroCurrent through the 50 ohms resistor is zeroCurrent through the 10 ohms resistor is 0.2ACurrent through the 10 ohms resistor is 0.6ACurrent through the 10 ohms resistor is 0.8ACurrent through the 10 ohms resistor is 1.6Av2=48Vv2=24Vv2=12Vv2=6VV1=4Vv1=15Vv1=42V

Answered: Find the voltage across the capacitors…

Engineering

Electrical Engineering

Find the voltage across the capacitors under dc conditions 10 Ω 50 Ω 70 Ω |_ + Μ 201 60 V ΜΕ C2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Related questions

Q: 1) For the circuit below determine the Thevenin equivalent circuit for the portion of the circuit…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: For the circuit shown in figure below, determine the magnitude and phase of the current / relative…

Q: Before you start using the unfamiliar Dimmer PPQQ2020 you decided to make an experiment with the…

A: Given: Before you start using the unfamiliar Dimmer PPQQ2020 you decided to make experiment with the…

Q: The following direct-current measurements were made on the two-port network shown in (Figure 1).…

Q: Find Rin(emitter), Ay, A₁, and A,, for the unloaded amplifier in Figure 6-57.

A: The required parameters can be calculated by using the DC and AC analysis of the amplifier circuit.

Q: The supply voltage of the op amp in the circuit is 16 V. If R₁ = 2,5000, assign a resistance value…

Q: Under steady-state DC conditions, find the current across the 2 ohms resistor

A: Under DC condition the inductor can be replaced with short circuit and capacitor can be replaced…

Q: 2.94 For a 3.6°, 2-o bipolar stepper motor, the stepping rate is 200 steps/second. The rotational…

A: Given,For a 2-ϕ bipolar stepper motor,β=3.6°.f=200 steps/second.

Q: The following data is provided for a switching power pole. Drain voltage V₁ = 10V Drain current ID…

A: Given Data: Drain voltage VD=10 V Drain current ID=5 A Switch resistance RDS_ON=25 mΩ Switch…

Q: r²+²+ -10-3 For the signals studied in problem 6-3 above, we can approximate the bandwidth of the…

A: Assumption for the message signal ωc=2π×10-7 rad/sec Kf=104π Kp=25π fc=10 MHz From the waveform,…

Q: Write four titles of projects, two of which are capital and two are without capital

A: We need to write four titles of projects, two of which are capital and two are without capital.

Q: A typical triac * O Conducts when not triggered None of these Conducts when not triggered in both…

Q: certain type of printer can print 50 pages in 3 minutes. How many pages can 4 printers of the same…

A: We need to find out total number of pages that given printer can print.

Q: Given the following impedances: X1-j0.15 X2-j0.15 XO=j0.2 Find: 1) Three phase fault 2) Single Line…

Q: Analyze the behavior of the biased series clipper using the ideal diode model and fill-up the table…

A: it is asked to analyze the behavior of given series clipper

Q: -2 A A light bulb input energy it's out put energy energy and heat. If cut part the efficiency 15…

Q: 2. Discuss Scheduling considerations. of tasks with Precedence

A: Note: We are authorized to answer one question at a time, since you have not mentioned which…

Q: 5. Write out the input-output equation for the system. x[n] w[n] 2 1 Z-¹ w[n- 1] y[n]

Q: Figure 2.0: A Two Poles-One Zero Circuit (b) Step 2: Assume that the Op-Amp circuit in Figure 2.0 is…

A: The given circuit diagram is shown below,

Q: A 400V, 3 –phase, 4 wire, star –connected system supplies three resistive loads of 18kW, 21kW and…

Q: Consider a situation where a point charge q is located at the height of h above con- ducting ground.…

A: In this question we need to find the force acting on charge and it's direction

Q: A finite line charge located at (0, y, 0)m, where a≤y≤b , has a line charge density of ρL = ycosy…

A: Given,At (0, y, 0)m, a finite line charge is located.where a≤y≤b.The line charge density…

Q: Find the SSE for a unit step and unit ramp functions of the following

A: Given: A control system, To find: Steady state error for unit step and unit ramp functions.

Q: Explain the prime mover in diesel plant and it's energy conversion

A: Given: Explain the prime mover in diesel plant and it's energy conversion.

Q: Problem #4) Given the following (steady-state) AC circuit: Is V = 120/0° volts Vs 10-j10 Ohms j10…

A: In this question We need to determine the all unknown parameters. We know Current in the impedance…

Q: a. b. C. Please find y[n] = x[n] * h[n] with following x[n] and h[n]. x[n] = 8[n] + 28[n − 1] + 38[n…

Q: Draw the sign given below for the range n € [-20,20]

A: In give problem we need to draw a graph for n vs x(n) we have n belongs to (-20 to 20) and x(n)=…

Q: For the following first-order system, G(s) = 11/(s+19) Let: τ - time constant tr - rise time ts -…

Q: View Policies Current Attempt in Progress The drawing shows three different resistors in two…

A: We need to find out the current and voltage for given circuit.

Q: Question#1 Using Mesh analysis find the mesh currents 11 and 12 and VI as phasors (amplitude and…

A: For the given circuit, R=2 ΩXL=1 ΩXC=2 Ω Where XL and XC are reactance of inductor and capacitor. It…

Q: Exercise 3: Consider the circuit shown below, where B₁-B2=200. Answer the following: a) What is the…

A: The required parameters can be calculated by using the DC and AC analysis of the multistage…

Q: *2.52 For the circuit shown in Fig. 2.116, find the equivalent resistance. All resistors are 1. Req…

Q: is(t) = A₁ · cos (1000t + 7) + A₂ · cos (2000t -) Assume the system is in steady state. Find the…

Q: Vio C₁ w 1 ΜΩ 2.7 ΚΩ 3.83 ΚΩ 16 V Μ Ca C I Vo

A: I have written this solution as handwritten solution. Hope you find the solution clear.

Q: B. step. Convert the decimal number (48.375) 10 to binary. Show your work step by

A: In this question we need to convert the given decimal numbers into binary

Q: 2. A series RL circuit has voltage and current equations of e = 141.42 sin 2n30t + 141.42 sin 2n90t…

A: For series RL ckt..impedance Z=R+jXL .. Where R is resistance and XL is inductive reactance..

Q: What is the efficiency of a transformer coupled class A amplifier for a supply of 12 V and output of…

A: Given- Transformer coupled class A amplifier- Supply = 12 V, Output of V (peak) = 12 V, To Find- The…

Q: Q2. (a) In an experiment on a piece of nichrome wire of 95.1 cm length and 0.21 mm diameter, the…

A: Q2. For the question 2 all questions are different from one another. The answers for all sub parts…

Q: Problem 1 (P 6.3-2): Find v, and i, for the circuit of Figure P 6.3-2. 12 V 3 kn m 2 k 1 kn 4 kn…

Q: The single-line diagram of a small power system is shown in Fig. 1. The corresponding reactance…

A: A single line diagram is a diagram representing the circuit components and their symbols and how the…

Q: A toroidal air cored coil with 1000 turns has a mean diameter of 50 cm, radius of each turn being 3…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: Discuss thermal ionization of donors and acceptors in the extrinsic semiconductors and hence find…

A: We need to discuss thermal ionization of donors and acceptors in the extrinsic semiconductors and w…

Q: An audio signal having the highest frequency of fM = 15 kHz is input to a 16-bit A/D counter type…

Q: What are the advantages of parallel operation ofalternators ?

A: Parallel Operation of Alternators :- Electric power systems are interconnected for economic and…

Q: what is the name of the first circuit (on the lift)? what is the name of the second circuit (on the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Applying the mesh analysis method, for the resolution of the following circuit, determine: a) The…

Q: Several components on a computer's motherboard are connected through parallel electrical conducting…

A: We need to explain components on a computer's motherboard are connected through parallel electrical…

Q: In your first job as an engineer, you propose to use the following system: 20洄洄洄洄洄洄洄洄 23 34 4th 5th…

A: According to the question, for the given system as shown below We need to redraw the circuit…

Q: Determine the resulting Thévenin equivalent for Circuit 1 by calculating the Voc (using Voltage…

A: The thevenin's voltage can be calculated by using the nodal analysis, the norton's current can be…

Q: The voltage source is 5+6sin(377t) V. What is the reading of the voltmeter at the AC scale setting?…

A: We need to find out reading of given AC voltmeter .

Question

Mark all that apply

Find the voltage across the capacitors under dc conditions
10 Ω
50 Ω
70 Ω
www
C₁
20Ω
60 V
1/2
C2

Capacitor behaves as an open under DC conditions
Capacitor behaves as an short under DC conditions
v1 is the same as the voltage across the 70 ohm resistor
v1 is NOT the same as the voltage across the 70 ohm resistor
Current through the 50 ohms resistor is NOT zero
Current through the 50 ohms resistor is zero
Current through the 10 ohms resistor is 0.2A
Current through the 10 ohms resistor is 0.6A
Current through the 10 ohms resistor is 0.8A
Current through the 10 ohms resistor is 1.6A
v2=48V
v2=24V
v2=12V
v2=6V
V1=4V
v1=15V
v1=42V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
Two capacitors having values of 80 F and 60 F are connected in series. What is the total capacitance?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
List the five capacitor replacement rules.