Find whether block A is moving up or down the plane in the figure below for the given data: Weight of block A = 300 N Weight of block B = 600 N The coefficient of static friction between plane AB and block A is 0.2 The coefficient of static friction between plane BC and block B is 0.25 Assume pulley as smooth. 60

Find whether block A is moving up or down the plane in the figure below for the given data: Weight of block A = 300 N Weight of block B = 600 N The coefficient of static friction between plane AB and block A is 0.2 The coefficient of static friction between plane BC and block B is 0.25 Assume pulley as smooth. 60

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.49P

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
In the figure, a flexible belt runs from A over the compound pulley B & back over P to a 200-N weight. The coefficient of friction is 1/π between the belt & the compound pulley P. Find the maximum weight W that can be supported w/out rotating the pulley P or slipping the belt on the pulley P.
The drum shown in the figure below has a weight of 100 N and rests on the floor for which the coefficient of static friction is 0.6. Assume tipping and determine the smallest value of P required for impending motion in N Assume sliding and determine the smallest value of P required for impending motion in N.
Find the least value of P required to cause the system of blocks shown in the figure to have impending motion to the left. The coefficient of friction under each block is 0.20.
In the figure shown the weights of the blocks are WA = 100 lb and WB =25 lb. Between all of the contacting surfaces, the coefficient of kinetic friction is 0.30. What F is necessary to move B to the left at a constant velocity?
PROBLEM: To prevent a box from sliding down an inclined plane, student A pushes on the box in the direction parallel to the incline, just hard enough to hold the box stationary. In an identical situation, student B pushes on the box horizontally. If the weight of the box w= 20.0 N, the angle made by the incline with the horizontal θ=25o, and the coefficient of static friction µs=0.16, who has the easier job?
A wedge assembly, composed of wedges X and Y, is designed to lift crate W whose weight is 1345 N, as shown in the figure below. What will be the maximum force P that can be applied before movement begins if the coefficient of friction for all surfaces of contact is 0.0875? Draw all necessary free-body diagrams and indicate the direction of impending motion.