Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt drive. Determine the length of flat belt, and the contact angle between belt and smaller pulley. Also determine the horse power. If the large pulley turns with speed (200 rpm) and the tension force in tight side is (1000 N), coefficient of friction u=0.25

Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt drive. Determine the length of flat belt, and the contact angle between belt and smaller pulley. Also determine the horse power. If the large pulley turns with speed (200 rpm) and the tension force in tight side is (1000 N), coefficient of friction u=0.25

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included angle of 40°, and density 1400kg/m 3 The angle of lap is 130° on the smaller wheel, the coefficient of friction is 0.4 and the maximum force allowed in the belt is 500N. Calculate the initial belt tension and reason for this.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
The block type handbrake shown in the figure has a width of 49 mm and an average friction coefficient of 0.32. Calculate the maximum pressure and braking moment on the lug to ensure the expectation of a thrust force of 483 N in the system with the reverse direction of the clock hand.
The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.