Firefighters are holding a nozzle at the end of a hose while trying to extinguish a fire. The nozzle inlet and exit diameters are 15 cm and 6 cm, respectively and the water flow rate is 5 m'/min. If the inlet pressure is 4 bar absolute, Semin (a) Determine the average water inlet velocity in m/s ( (b) Determine the average water exit velocity in m/s (b) By neglecting the body and friction force across the nozzle, find the horizontal resistance force required of the firefighters to hold the nozzle in kN. (: (c) Fill the table below' )

Firefighters are holding a nozzle at the end of a hose while trying to extinguish a fire. The nozzle inlet and exit diameters are 15 cm and 6 cm, respectively and the water flow rate is 5 m'/min. If the inlet pressure is 4 bar absolute, Semin (a) Determine the average water inlet velocity in m/s ( (b) Determine the average water exit velocity in m/s (b) By neglecting the body and friction force across the nozzle, find the horizontal resistance force required of the firefighters to hold the nozzle in kN. (: (c) Fill the table below' )

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. Determine the work done per unit weight of water, in Newton-Meter per Newton.
A jet of water, issuing from sharp-edged vertical orifice under a constant head of 60 cm , has the horizontal and vertical coordinates measured from vena contracta at a certain point as 10. cm and 0.45 cm respevtively. Find Cc if Cd= 0.60.include your free body diagrama.0.612 b.0.962 c.0.98 d.0.623
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees. B. Determine the Outlet Vane Angle, in degrees. C. Determine the work done per unit weight of water, in Newton-Meter per Newton.
Water enters a two-armed lawn sprinkler along a vertical axis at a rate of 60 L/s and leaves the sprinkler nozzles as 2-cm diameter jets at a 30°angle, determine the rotational speed in RPM of the sprinkler.
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
A 5 cm diameter of water jet strikes a flat plate which held normal to the direction of the water jet and with velocity 3.1617 m/s. Find the work done/s (in Nm/s) (answer in one decimal place) by the jet when the plate is moving with a velocity of 2m/s away from the jet along the same line.
A 5-cm-diameter horizontal jet of water, with velocity 30 m/s, strikes the tip of a horizontal cone, which deflects the water by 60° from its original direction. How much force is required to hold the cone against the water stream?
A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine the elevation in meters, above the water sump level, to which the jet would reach. Neglect all losses. a.24.04 b.0.10 c.20.31 d.0.52
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
A fluid moves in a steady flow manner between two sections in a flow line. At the entrance section A1 = 1m², V1= 0.5 m/s, P1= 4kgm/m³. At the exit section: A2 = 0.2m², V2= 0.20m³/kgm. Calculate the mass flow rate in kg/s and the speed at section 2 in m/s.
Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long horizontal section with a 90° elbow at the exit to force the water to be discharged downward, as shown, in the vertical direction. Water discharges to atmospheric air at a velocity of 5 m/s, and the mass of the pipe section when filled with water is 17 kg per meter length. Determine the moment acting at the intersection of the vertical and horizontal sections of the pipe (point A). What would your answer be if the flow were discharged upward instead of downward?