FLUID MECHANICS-WATER HAMMER: A valve at the end of a gasoline pipeline is rapidly closed (assume instantaneously). If the gasoline velocity was initially 12m/s, what will be the water hammer pressure rise? The bulk modulus of the gasoline is 715 MPa, and the density of the gasoline is 680 kg/m3.

FLUID MECHANICS-WATER HAMMER: A valve at the end of a gasoline pipeline is rapidly closed (assume instantaneously). If the gasoline velocity was initially 12m/s, what will be the water hammer pressure rise? The bulk modulus of the gasoline is 715 MPa, and the density of the gasoline is 680 kg/m3.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Related questions

Q: With the schematic diagram of a pump, tanks, and piping determine the following: 1) The velocity of…

A: Given, Pump and pipe system

Q: A cylindrical object 82mm diameter, 155mm height and a mass of 611g, is placed in the tank, which…

Q: 15m SAE 30 ol Water 25m Oiive ol 29m Mercury 04m

Q: A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5…

Q: Consider a steam turbine power plant operating near critical pressure, as shown in Fig. below. As a…

A: Given:- T1=700 C P1=P4=15MPa P2=P3=20kPa To find:- a) Isentropic Turbine efficiency b) Pump work…

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

Q: F= 5 kN F = 8 kN 45° 60 F What should be the value of F3 and F4 in kN so that the system is in…

A: To find value of force F3 and F4

Q: Subject: Fluid Mechanics/Hydraulics 1.) What is the specific weight of air in N/m3 at 442 kPa…

Q: A nozzle of inner radius 1.06 mm is connected to a hose of inner radius 9.05 mm. The nozzle shoots…

Q: Q1.A. A square block of (250 mm) side and weighing (1.1 kN) on an edge slides down an incline on a…

A: This question is related to the Fluid Mechanics.

Q: 11. A liquid flowss through two similar pipes 1 and 2. If the ratio of their flow velocities v1 : v2…

A: Head loss is directly proportional to the square of velocity.

Q: SAE 30 oil 15m Water 2-5m Olive oil 29m Mercury 04m

Q: 2.) A liquid having a Reynolds number of 1500 flows thru a 200-mm diameter pipe, 220m long. The head…

Q: A hydraulic jack contains 2.0 litres of oil as the working fluid. The compressibility of the oil is…

A: Given, Volume of oil(V) = 2ltr=2×10^-3 m^ compressibility (B)= 1.98×10^-10/pa Pressure (p)…

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

Q: oil of viscosity 9 poise is flowing through a horizontal pipe of 60 mm diameter. the flow is…

A: Given data; Viscosity of oil = u = 9poise Diameter of pipe=D = 60mm Pressure drop = 1800kN/m² Length…

Q: Meriam red oil, SG=0.827 P2.32 Water A 18 cm H 35 cm B Mercury

A: Given data:- The PB-PA=89.5 kPa=89500 Pa The specific weight of water is, Wwater=9790 N/m3 The…

Q: A hydraulic jack contains 2.0 litres of oil as the working fluid. The compressibility of the oil is…

A: Finding out absolute decrease in the volume of the oil.

Q: An oil of density 892 kg/m³ is flowing in a pipe having an internal diameter 5cm. This pipe is…

Q: At a given point in the high-speed flow over an airplane wing, the local Mach number, pressure and…

A: Given Local Mach number = 0.7 Pressure = 0.9atm Temperature = 250K To find, po,To,p*,T* and a*

Q: a) Determine the dynamic viscosity of the lubricating oil that must be placed in the space between…

A: The values and diagram given in the question are as follows: Diameter of the inner cylinder(di)=11…

Q: A sealed vertical cylinder 1.2m in diameter and 3m high is filled with gasoline whose density is 740…

A: Given data:

Q: 200 cm 20 cm 60 cm 3. The cylinder in the figure is to be placed in fresh water. The top potion of…

A: To find Specific weight of cylinder?

Q: 10. A beaker is filled with a liquid of density p1 up to a certain height. A is a point, h m…

A: Given, Density of liquid 1 = ρ1 Density of liquid 2 = ρ2 Depth of point A before, replacing the…

Q: The head of water over an orifice of diameter 100.mm is 10 m. The water coming out from orifice is…

Q: If a natural gas has a specific gravity of 0.60 relative to air at 14.70-psi-abs and 68 degrees…

Q: 24. A mercury barometer at the base of a mountain reads 736 mm. At the same time, another barometer…

A: Note : According to our company's guidelines we are allowed to solve 1st 3 questions only. Let A be…

Q: 2. Calculate the actual work done on the 200 g mass using W = mgh. Be careful to use only the change…

A: The given data is: Mass=200 g The work done, W=mgh The work done to raise the mass to the C…

Q: Calculate the location of the center of pressure, Lp, to in m to the nearest 1000th. Fluid: Orange…

A: NOTE : as per our guidelines we are supposed to answer only one question. Kindly repost the another…

Q: If the atmospheric pressure is 101.30 kPa and the absolute pressure at the bottom of the tank as…

Q: An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per…

A: Given; Diameter of nozzle=5"=5×0.0254m=0.127m Velocity of water flowing out = 5m/s Rate at which…

Q: A container of natural gas is measured at Time 1: T1=10oC, p1=100 kPa and at Time 2: T2=10oC, p2=200…

A: Given: At time 1, The temperate T1 is 10 oC. The pressure p1 is 100 kPa. At time 2, The temperate T2…

Q: Diameter of the cylindrical tank = 4m Diameter of circular orifice = 10 cm Cv = 0.98 Cc = 0.61…

A: Experiments studied the influence of flow velocity and flow rate as well as different deviation…

Q: A cylindrical object 84mm diameter, 158mm height and a mass of 589g, is placed in the tank, which…

A: To determine the height of the cylinder that floats above the oil. Given, Diameter of the cylinder…

Q: oil of viscosity 9 poise is flowing through a horizontal pipe of 60 mm diameter. the flow is…

A: To find :- Velocity of flow of oil V

Q: If benzene flows through the pipe line showed in the figure 3, and its velocity where is the benzene…

A: Using continuity equation :vAAA=vBAB8π4(6)2=vBπ4(4)2vB=18fpsso,

Q: What is the pressure in Kpa 1.20 m below the surface of a liquid of sp. gr. 1.20 if the gas pressure…

Q: A flocculation tank contains 1800 m³ of water, which is mixed using paddles at an average velocity…

A: Given data in question Volume Velocity gradient Temperature Dynamic viscosity To find out…

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

A: Volume of water in container=1m3 It is required to determine the change in volume of water when a…

Q: A cylinder glass tubing 2.8 cm. inside diameter and 90 cm long with one end closed is immersed…

A: Given:- The inside diameter of a cylinder glass tubing = 2.8 cm The length of the cylinder = 90 cm…

Q: A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419x10-3 Kg/m-s is…

A: step 1-

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

Q: An initially empty tank on Earth is being filled with water so that the height of the water in the…

Q: A closed tank containing 2 layers of fluids is discharging its contents through an orifice as shown…

A: step 1-

Q: Oil flows thru a 50 mm diameter pipe having a head loss of 12 m. The length of the pipe is 120 m.…

A: Given, Diameter of pipe (D) = 50mm Head loss (hL) = 12m Length of the pipe (L) = 120m Reynolds…

Q: - A certain gas a value of R = .18896 KJ/kg°K and K = 1.288. Calculate the value of Cp and Cv.

Q: Given the bulk modulus of water B2.1x10 Pa2.1 GPa, What increase in pressure needs to be applied to…

Q: A cylindrical tank with a diameter of 80 cm is partially filled with SAE 10W oil (ρ = 870 kg/m3). If…

A: V = mρ where ; m = mass of oil in tank = 340 kg ρ = 870 kg/m3 V = 340870 = 0.391 m3

Q: Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter…

A: GIven diameter of disk d=5 cm =0.05 m amd height h=1 cm =0.01 m velocity du=30cm/4…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

FLUID MECHANICS-WATER HAMMER:

A valve at the end of a gasoline pipeline is rapidly closed (assume instantaneously). If the gasoline velocity was initially 12m/s, what will be the water hammer pressure rise? The bulk modulus of the gasoline is 715 MPa, and the density of the gasoline is 680 kg/m³.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
Obtain the values of vapor pressures of alcohol, water, and glycerin at a room temperature of 20 C.
Consider a rectangular plate of width B = 1m (measured in the direction normal to the plane of this sheet) and negligible thickness, which separates two fluids of densities ρ and ρw. A mass of density ρs is supported by an inextensible rope that passes through a pulley connected to one end of the plate. Consider that ρ = 1.59ρw and ρs = 2.40ρw, where ρw = 1000 kg/m3. Determine the volume that this mass must have for the system to remain in equilibrium, as shown in the figure.
Fluid Mechanics Last Fall, researchers using an unmanned submarine discovered a coral reef at the unprecenented depth of 1/2 mile. The density of seawater at the surface of the ocean is 1025kg/m3 and the bulk modulus of elasticty of seawater is 2.34*109 Pa. A volume of air is taken downward to the coral reef. Assuming an absolute air pressure at the ocean surface of 1 atm, and that the air taken to the reef behaves as an isothermal gas. Find the pressure of the air at that depth. Find the fractional change in denisity and volume of the air at that depth.
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 Nper cubic meter enters the bottom of the tank with a uniform velocity of—assume values with decimals between 3 to 4 m per second—enters thestack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack. Please add the figure , thank you!
the reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. if the tank is 30 cm. deep, and is contaminated with 3.42 cm. of water at the bottom, how many meters of air remains at the top when the gage indicates "FULL"? use weight of: gasoline = 6.62 kN/m^3; air = 14.67 N/m^3. the tank is closed.
Oil flows thru a 50 mm diameter pipe having a head loss of 12 m. The length of the pipe is 120 m. long. If the oil has a Reynold's Number equal to 1600; a. compute the velocity of the oil flowing in the pipe. (unit of the answer is in m/s) b. what is the equivalent viscosity in stokes? (unit of the answer is in stokes)
The system in Figure 2-5 is at 20oC. If atmospheric pressure is 101.03 kPa and the absolute pressure at the bottom of the tank is 231.3 kPa, what is the specific gravity of olive oil? Note: density of water=9.79 kN/m3 (specific gravity SAE oil is 0.89, h SAE oil is 1.5m, h water is 2.5m, H olive oil is 2.9m, h mercury is 0.4m, specific gravity mercury is 13.6 ) and use g=9.79m/s2. a) 1.39 b) 1.29 c) 1.49 d) 1.59 e) none of the above
In a falling ball viscometer, a steel ball 1.2 mm in diameter is allowed to fall freely in a heavy oil having s= 0.802. The Steel specific weight is 77 kN/m3. If the ball observed to fall 250 mm in 10.4 seconds, calculate the viscosity of the oil?
An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per second. At the same time, receiving a fluid at a rate of 265 US Gal per minute. At a certain point, the tank is considered to be quarter full . Find the (a) water level and the (b) mass change in the tank 15 minutes later. Given: tank diameter = 10 ft tank height = 20 ft